• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.3
• /
• pp.149-158
• /
• 2005

This paper describes design, fabrication, and application of the silicon based temperature controllable micro reactor. In order to achieve fast temperature variation and low energy consumption, reaction chamber of the micro reactor was thermally isolated by etching the highly conductive silicon around the reaction chamber. Compared with the model not having thermally isolated structure, the thermally isolated micro reactor showed enhanced thermal performances such as fast temperature variation and low energy consumption. The performance enhancements of the micro reactor due to etched holes were verified by thermal experiment and numerical analysis. Regarding to 42 percents reduction of the thermal mass achieved by the etched holes, approximately 4 times faster thermal variation and 5 times smaller energy consumption were acquired. The total size of the fabricated micro reactor was $37{\times}30{\times}1mm^{3}$. Microchannel and reaction chamber were formed on the silicon substrate. The openings of channel and chamber were covered by the glass substrate. The Pt electrodes for heater and sensor are fabricated on the backside of silicon substrate below the reaction chamber. The dimension of channel cross section was $200{\times}100{\mu}m^{2}$. The volume of reaction chamber was $4{\mu}l$. The temperature of the micro reactor was controlled and measured simultaneously with NI DAQ PCI-MIO-16E-l board and LabVIEW program. Finally, the fabricated micro reactor and the temperature control system were applied to the thermal denaturation and the trypsin digestion of protein. BSA(bovine serum albumin) was chosen for the test sample. It was successfully shown that BSA was successfully denatured at $75^{\circ}C$ for 1 min and digested by trypsin at $37^{\circ}C$ for 10 min.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.26 no.4
• /
• pp.225-243
• /
• 2014

As the economic matters are involved, applying the WEC, which is used for controlling waves as well as utilizing the wave energy on existing breakwater, is preferred rather than installing exclusive WEC. This study examines the OWC mounted on a pressurized air chamber floating breakwater regarding the functionality of both breakwater and wave-power generation. In order to verify the performance as a WEC, the velocity of air flow from pressurized air chamber to WEC has to be evaluated properly. Therefore, numerical simulation was implemented based on BEM from linear velocity potential theory as well as Boyle's law with the state equation to analyze pressurized air flow. The validity of the obtained values can be determined by comparing the previous results from numerical analysis and empirically obtained values of different shapes. In the actual numerical analysis, properties of wave deformation around OWC system mounted on fixed type and floating type breakwaters, motions of the structure with air flow velocities are investigated. Since, the wind power generating system can be hybridized on the structure, it is expected to be applied on complex power generation system which generates both wind and wave power energy.

• Korean Journal of Heritage: History & Science
• /
• v.47 no.2
• /
• pp.68-84
• /
• 2014

The royal tombs of Baekje(백제), after the transfer of the capital to the Geumgang(riv)(금강) basin, changed to Songsanri(송산리) style(stone chamber) ${\rightarrow}$ Southern dynastic(남조) style(brick chamber) ${\rightarrow}$ Neungsanri(능산리) style(stone chamber). The most special feature of this process is the change of the ceiling structure. The ceiling had been changed from dome(Songsanri style) ${\rightarrow}$ tunnel ceiling(transition period of brick tombs and Neungsanri style) ${\rightarrow}$ a roof style(is Neungsanri style of three imitate type, trapezoid, triangle, flattened ceiling). The most special feature among this process is Neungsanri style(stone chamber), created especially in Baekje. The royal tombs of Baekje didn't lay stress on the mound, so the mound is not noticeable. It is result that they more stressed on basin of the boundary than showed off individual tomb, and this is count as an element of China Southern dynasty. Boundary of the royal tomb of Baekje, after the transfer of the capital to south, were changed from royal family's boundary to single independent's. Those are Songsanri's and Neungsanri's, these are the pair tombs(쌍릉) of Iksan(익산). That is influence of the Southern dynasty, reflect the theory of divination based on topography completely, this is influence of the China Sui(수) and the early Tang(당) dynasty's system of boundary of the royal tomb. Besides the royal tomb, they also buried a closely related person, in the boundary of the royal tomb. And facilities for memorial ceremony were existed too. An altar was equipped in Songsanri's boundary of the royal tomb, it was seen a kind of character of a sanctuary for progenitor. Neungsanri's boundary of the royal tomb were equipped with an open-aired altar that performed memorial ceremony about communal royal tombs, and also equipped a temple, was needed to pray for the happiness of the dead. This structure and arrangement are very similar to Seoakdong(서악동) of Silla(신라).

• Journal of Electrical Engineering and Technology
• /
• v.6 no.4
• /
• pp.551-555
• /
• 2011

The Crab label tag with a loop matching feed and a modified dipole antenna structure was proposed. The antenna impedance is conjugated easily to a radio frequency identification IC chip impedance by a loop matching feed. The reading range of the crab structure tag is 0.9-1.0 m from the upper side of the formula milk can lid. The fabricated label tag size is $44.0{\times}44.0mm^2$. The operating frequency at -3 dB return loss is 861.0-929.0 MHz, and the maximum reading range at the anechoic chamber is 1.5 m.

• Journal of Mechanical Science and Technology
• /
• v.19 no.3
• /
• pp.894-904
• /
• 2005

The flow structure inside the intake head greatly affects the working efficiency of a vacuum cleaner such as suction power and aero-acoustic noise. In this study, the flow inside intake heads of a vacuum cleaner was investigated using qualitative flow visualization and quantitative PIV (Particle Image Velocimetry) techniques. The aerodynamic power, suction efficiency and noise level of the intake heads were also measured. In order to improve the performance of the vacuum cleaner, inner structure of the flow paths of the intake head, such as trench height and shape of connection chamber were modified. The flow structures of modified intake heads were compared with that of the original intake head. The aero-acoustic noise caused by flow separation was reduced and the suction efficiency was also changed due to flow path modification of intake head. In this paper, the variations of flow fields for different intake heads are presented and discussed together with results of aerodynamic power, suction efficiency and noise level.

• Journal of the Korean Society for Railway
• /
• v.11 no.1
• /
• pp.1-6
• /
• 2008

Sound transmission characteristics are investigated on the test specimen for the railway vehicle's floor section. Transmission loss on the honeycomb structure has been examined experimentally with the reverberation chamber. Predicted transmission loss values using NASTRAN, AUTOSEA2, are compared with measured Haloes and the effect of resonance on the transmission loss is identified. Transmission loss of different shapes of honeycomb structure are predicted.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.71-77
• /
• 2010

As a hybrid model of continuum motion description which combines the advantages of classical kinematical descriptions i.e. Lagrangian and Eulerian description, the ALE (Arbitrary Lagrangian Eulerian) description is adopted for the simulation of a fluid-structure interaction of solid propellant rocket interior. The fluid-structure interaction phenomenon with the deformation of solid domain during the simulation. The developed solver is applied flow and propellant structure. The computed results show complex flow physics in the combustion chamber and the behavior of a solid propellant deformation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.171-172
• /
• 2006

Most existing studies for stress analysis of teeth have employed small number of teeth, and used big element size using F-E models. Therefore, the results are not accuracy enough for showing the internal stress variation. 15 males' and 13 females' mandibular first premolar are employed for internal structure's study of teeth and small element size for a FE model are used. According to these processes, stress distribution of internal parts of teeth are well shown, and the stresses are varied a lot between enamel layer and dentine layer, but there is little variation on pulp chamber.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.19-26
• /
• 2002

The objective of this study is to examine a DI(Direct Injection) gasoline spray development process under different ambient pressures using PIV(Particle Image Velocimetry). fuel spray experiments were performed within a constant volume chamber. The spray structure, velocity maps, velocity and vorticity contours were obtained to investigate its spray characteristics. It was found that higher ambient pressure has a significant effect on radial growth of the spray. The position which has a maximum velocity moved from the spray edge to the spray center as ambient pressure was increased. Higher ambient pressure moved a maximum vorticity position upward of the spray.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.760-766
• /
• 2006

In this paper, we present a wideband patch antenna with folded and shorted structure for 5 GHz WLAN(Wireless Local Area Network). The proposed antenna used folded and shorted structure in the rectangular patch for miniaturization and wide frequency bandwidth. The antenna was designed by using 3D simulation program, HFSS(High Frequency Structure Simulator) software of the Ansoft company and the implemented antenna was measured by using HP 8720c network analyzer and far field measurement chamber. Simulation result on the return loss shows fairly good characteristic of at least 13.41dB in whole frequency range of interests, and the 10dB bandwidth is 1,523MHz which shows wide bandwidth characteristic. And the simulated maximum gain of the proposed antenna is 6.57 dBi at 5.825GHz. Measured result for the 10dB bandwidth of the implemented folded and shorted structure antenna is 1,377 MHz. Measured maximum gain of the implemented antenna is 6.87dBi at 5.775GHz. Measured results for the implemented antenna showed applicable performances for the 5 GHz WLAN.