• Transactions on Electrical and Electronic Materials
• /
• 제10권1호
• /
• pp.5-8
• /
• 2009

The reliability of multilayer ceramic capacitor with active thin dielectric layer was investigated by highly accelerated life test at various stress condition. The distribution of multilayer ceramic capacitor failure times is plotted as a function of time from Weibull distribution function. According to the test result, voltage acceleration factor is obtained from 2.24 to 2.96. The acceleration by temperature is much higher than other values of active thick dielectric layer. It is clear that median time to failure is affected by the stress voltage for high volumetric efficiency ceramic capacitors with active thin dielectric layer. The degradation under stress of voltage involves electromigration and accumulation of oxygen vacancy at Ni electrode interface of cathode.

• 한국세라믹학회지
• /
• 제37권3호
• /
• pp.263-270
• /
• 2000

The Pt/copper oxide/n-Si electrodes were fabricated by depositing copper oxide thin film of 500${\AA}$ and very thin Pt layer on the n-type (100) Si substrate. hotoelectrochemical properties and stability profiles of the electrodes were investigated as a function of deposition time of Pt layer. As the deposition time of Pt layer increased up to 10 seconds, the photocurrent and quantum efficiency were increased and then decreased with further depositing time. The better cell stability was observed for the electrode with longer deposition time. The improvements in above photoelectrochemical properties indicate that Pt layer acts as a catalyst layer at electrode/electrolyte interface as well as a protective layer. The decreasing tendency of the photocurrent and efficiency for the electrode with Pt layer deposited above 20 seconds was explained as an increases in probbility of electron-hole pair recombination and also the absorbing photon loss at electrode surface due to the excessive thickness of Pt layer. The results were confirmed by impedance spectroscopy, mutiple cycle voltammograms and microstructural analyses.

• Bulletin of the Korean Chemical Society
• /
• 제20권8호
• /
• pp.869-874
• /
• 1999

In this paper, electrochemical techniques are used to investigate hydrothermal-electrochemically formation of barium titanate (BT) ceramic films. For comparison, the electrochemical behaviors of anodic titanium oxide films formed in alkaline solution were also investigated both at room temperature and in hydrothermal condition at 150.0 ℃. Film structure and morphology were identified by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Titanium oxide films produced at different potentials exhibit different film morphology. The breakdown of titanium oxide films anodic growth on Ti electrode plays an important roles in the formation of BT films. BT films can grow on anodic oxide/metal substrate interface by short-circuit path, and the dissolution-precipitation processes on the ceramic film/solution interface control the film structure and morphology. Based upon the current experimental results and our previous work, extensively schematic proce-dures are proposed to model the mechanism of ceramic film formation by hydrothermal-electrochemical method.

• 한국세라믹학회지
• /
• 제50권2호
• /
• pp.163-167
• /
• 2013

A modified two-point impedance spectroscopy technique exploits the geometric constriction between an electrolyte and a cathode with an emphasis on semispherical-shaped electrolytes. The spatial limitation in the electrolyte/electrode interface leads to local amplification of the electrochemical reaction occurring in the corresponding electrolyte/electrode region. The modified impedance spectroscopy was applied to electrical monitoring of a YSZ ($Y_2O_3$-stabilized $ZrO_2$)/SSC ($Sm_{0.5}Sr_{0.5}CoO_3$) system. The resolved bulk and interfacial component was numerically analyzed in combination with an equivalent circuit model. The effectiveness of the "spreading resistance" concept is validated by analysis of the electrode polarization in the cathode materials of solid oxide fuel cells.

• 한국세라믹학회지
• /
• 제44권12호
• /
• pp.727-732
• /
• 2007

In order to fabricate a highly performing cathode for low-temperature type solid oxide fuel cells working at below $700^{\circ}C$, electrode microstructure control and electrode polarization measurement were performed with an electronic conductor, $La_{0.8}Sr_{0.2}MnO_3$ (LSM) and a mixed conductor, $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$(LSCF). For both cathode materials, when $Sm_{0.2}Ce_{0.8}O_2$ (SDC) buffer layer was formed between the cathode and yttria-stabilized zirconia (YSZ) electrolyte, interfacial reaction products were effectively prevented at the high temperature of cathode sintering and the electrode polarization was also reduced. Moreover, cathode polarization was greatly reduced by applying the SDC sol-gel coating on the cathode pore surface, which can increase triple phase boundary from the electrolyte interface to the electrode surface. For the LSCF cathode with the SDC buffer layer and modified by the SDC sol-gel coating on the cathode pore surface, the cathode resistance was as low as 0.11 ${\Omega}{\cdot}cm^2$ measured at $700^{\circ}C$ in air atmosphere.

• 세라미스트
• /
• 제22권4호
• /
• pp.402-416
• /
• 2019

The development of next-generation secondary batteries, including lithium-ion batteries (LIB), requires performance enhancements such as high energy/high power density, low cost, long life, and excellent safety. The discovery of new materials with such requirements is a challenging and time-consuming process with great difficulty. To pursue this challenging endeavor, it is pivotal to understand the structure and interface of electrode materials in a multiscale level at the atomic, molecular, macro-scale during charging / discharging. In this regard, various advanced material characterization tools, including the first-principle calculation, high-resolution electron microscopy, and synchrotron-based X-ray techniques, have been actively employed to understand the charge storage- and degradation-mechanisms of various electrode materials. In this article, we introduce and review recent advances in in-situ synchrotron-based x-ray techniques to study electrode materials for LIBs during thermal degradation and charging/discharging. We show that the fundamental understanding of the structure and interface of the battery materials gained through these advanced in-situ investigations provides valuable insight into designing next-generation electrode materials with significantly improved performance in terms of high energy/high power density, low cost, long life, and excellent safety.

• 한국세라믹학회지
• /
• 제31권8호
• /
• pp.869-873
• /
• 1994

Electrical properties of each interfacial layers on semiconducting ceramics have been analized and evaluated by complex impedance resonance method as functions of ambient temperatures and applied voltages. From the analytical results, it can be observed that the interfacial layers in a semiconducting ceramics vary individually with the ambient temperature and then this influence the total properties. Also, it has been confirmed that the applied voltage on semiconducting ceramics affect mainly the electrode interface, and thus the resistance and capacitance decrease due to the variation of potential barrier layers.

• 세라미스트
• /
• 제9권6호
• /
• pp.24-29
• /
• 2006

Electron beam physical vapor deposition (EB-PVD) process has currently been applied to thermal barrier coatings (TBCs) for aircraft engines. Due to unique columnar structure, EB-PVD TBCs have advantages in resistances to thermal shock and thermal cycle for their applications, compared to films prepared by plasma spray By the EB-PVD equipment, we successfully obtained yttria-stabilized zirconia (YSZ) layer which has columnar and feather like structure including a large amount of nano size pores and gaps. The EB-PVD technique has been developed for coating functional perovskite type oxides such as (La, Sr)MnO3. Electrode properties have been improved by interface and structural control.

• 한국세라믹학회지
• /
• 제36권2호
• /
• pp.172-177
• /
• 1999

흑연 및 카본재료는 알칼리 금속을 intercalation/de-intercalation 시킬수 있는 특성을 지니고 있으며, 또한 Li-intercalated carbon의 화학 potential이 Li 금속에 가까운 낮은 값을 지닌 특성으로 리튬 이차전지의 anode 전극재료로서 널리 쓰일 가능성이 매우 크다. 본 연구에서는 카본재료 중 mesocarbon microbeads (MCMB)를 리튬 이차전지의 anode 전극재료로 사용하여 전지반응을 수행하고, 전극의 충.방 전 특성과 전극계면 반응특성에 대하여 연구하였다. 즉, Li/carbon(MCMB) 전지 cell를 제작하고 전해질과 전극계면에서 일어나는 전기화학 반응특성을 충.방 전 시험, Potentionat/Galvanostat 시험, FT-IR 분석, XRD 및 SED 분석에 의하여 고찰하였다. 전지반응이 진행되면서 전극과 전해질 계면에서 고체상태의 부동태 막 (passivation film)이 형성되었으며, 일단 형성된 막은 전해질 내에 용해되지 않고 충.방 전 횟수가 증가하면서 두께가 증가되었다. 또한, 이러한 전극 계면에서 형성된 부동태 막과 중전용량과의 관계에 대하여 고찰하였다.

• 세라미스트
• /
• 제22권2호
• /
• pp.170-181
• /
• 2019

All-solid-state batteries have received increasing attention because of their high safety aspect and high energy and power densities. However, the inferior solid-solid interfaces between solid electrolyte and active materials in electrode, which cause high interfacial resistance, reduce ion and electron transfer rate and limit battery performance. Recently, spark plasma sintering is emerging as a promising technique for fabricating solid electrolytes and composite-electrodes. Herein, this paper focuses on the overview of spark plasma sintering to fabricate solid electrolytes and composite-electrodes for all-solid-state batteries. In the end, future opportunities and challenges associated with SPS technique for all-solid-state batteries are described.