• 한국세라믹학회지
• /
• 제30권3호
• /
• pp.215-221
• /
• 1993

The Hydroxyapatite powders were prepared by Wet-direct and Hydrothermal synthesis using Ca(NO3)2.4H2O and (NH4)2.HPO4.Stoichiometric and good cristalline HAp powders were obtained 9$0^{\circ}C$ by wet-direct process. The aspect ratio of HAp powders prepared by hydrothermal synthesis was increased with increasing synthetic temperature. The HAp particles obtained at 20$0^{\circ}C$ for 10hr were needle shaped ultra fine crystals, about 100nm in size. Small amount of TCP was obtained above 80$0^{\circ}C$ after heat-treatment of hydrothermally synthesized HAp but good crystalline HAp phase was maintained up to 120$0^{\circ}C$ as the primary phase.

• 공업화학
• /
• 제16권3호
• /
• pp.305-311
• /
• 2005

열플라즈마 공정은 고온, 고활성, 초급냉 등의 탁월한 특징을 갖고 있으며, 다양한 분야에 적용되고 있다. 본 총설에서는 열플라즈마 공정의 특징과 초미립 분말의 제조를 위한 시스템의 구성을 기술한다. 여기에는 금속, 세라믹, 복합 초미립 분말이 포함되며, 공정의 개발을 위하여 요구되는 핵심기술에 대하여 논의한다. 저자 등은 열플라즈마를 이용하여 다양한 형태의 고품질 초미립 분말을 제조하는 공정의 가능성을 제시하고자 하였다.

• 한국세라믹학회지
• /
• 제29권9호
• /
• pp.681-688
• /
• 1992

Ultrafine Si3N4 and Si3N4+SiC mixed powders were synthesized through thermal plasma chemical vapor deposition(CVD) using a hybrid plasma, which was characterized by the supersposition of a radio-frequency plasma and arc jet. The reactant SiCl4 was injected into an arc jet and completely decomposed in a hybrid plasma, and the second reactant CH4 and/or NH3 mixed with H2 were injected into the tail flame through double stage ring slits. In the case of ultrafine Si3N4 powder synthesis, reaction efficiency increased significantly by double stage injection compared to single stage one, although crystallizing behaviors depended upon injection speed of reactive quenching gas (NH3+N2) and injection method. For the preparation of Si2N4+SiC mixed powders, N/C composition ratio could be controlled by regulating the injection speed of NH3 and/or CH4 reactant and H2 quenching gas mixtures as well as by adjusting the reaction space.

• 한국세라믹학회지
• /
• 제28권7호
• /
• pp.568-576
• /
• 1991

The powder characterization and sintering behavior of alkoxide-derived alumina powders prepared by esterification were investigated. The dried powders were calcined at 700$^{\circ}C$, 900$^{\circ}C$, 1080$^{\circ}C$, 1170$^{\circ}C$ for 1 h. and the resulting crystalline forms were amorphous, {{{{ gamma }} phase, {{{{ theta }}+{{{{ alpha }} phase, and {{{{ alpha }} phase, respectively. The sinterability was best in the case of being calcined at 1170$^{\circ}C$. It was most effective to disperse sintering additive in the initial stage from which acetate was formed. At 1600$^{\circ}C$ for 4 h, 98.5% of relative density was obtained when MgO and Fe2O3 were simultaneously doped, and dense sintered body whose density was near theoretical value was obtained when heating schedule was controlled.

• 한국세라믹학회지
• /
• 제24권6호
• /
• pp.593-601
• /
• 1987

A thermodynamic model to predict the stability of the water-in-oil type emulsion and the size of the droplets in stable emulsions was developed. Using this model, the effects of various factors government the droplet size in the metal salt solution-kerosene-span 80 system for the preparation of Al2O3-ZrO2 composite powders were investigated. It was shown that the given emulsion systems were thermodynamically unstable in every case but could be kinetically meta stable. When radius ofthe droplet was below nm, the increase in entropy change due to the configurational contribution of small droplets dominated the total free energy change for emulsification. The optimum conditions under which smaller deoplet was obtained were proposed and the validity of the model was proved with diameters of the droplet and composite powders experimentally determined.

• 한국세라믹학회지
• /
• 제34권11호
• /
• pp.1159-1164
• /
• 1997

Magnetite(Fe3O4) powders were synthesized through glycothermal reaction by using crystalline $\alpha$-FeOOH as precursor and ethyleanne glycol as solvent. The phase, morphology and particle size of synthesized powders were characterized by XRD and an SEM. When only ethylene glycol was used as solvent, the phase was transformed from $\alpha$-FeOOH to $\alpha$-Fe2O3 and finally Fe3O4 at 27$0^{\circ}C$ for 6hr without morphological change. But by addition of water, Fe3O4 powders were synthesized at 23$0^{\circ}C$ for 3hr through solution-recrystalization process. As the content of water addition increased, the particle shape changed from sphere to octahedron and the partcle size increased. When the excess amount of water added, residual $\alpha$-FeOOH or $\alpha$-Fe2O3 was recrystalized.

• 한국세라믹학회지
• /
• 제30권2호
• /
• pp.115-122
• /
• 1993

Transparent Al2O3 and TiO2 clear sols prepared by hydrolysis and subsequent peptization were mixed into wet gel. EDS analysis for this gel showed that wet gel was extremely homogeneous in chemical composition. Calcination of the wet gel at 120$0^{\circ}C$ for 50 minutes resulted in Al2O3-TiO2 nanocomposite powders where TiO2 particles of 101~102 nanometer were dispersed in the Al2O3 matrix. Both powders were sintered for 4 hours in the temperature range over 1500~1$650^{\circ}C$ with and without 5wt% MgO sintering aid. Among these sintered bodies, nanocomposite powder compacts sintered at 1$650^{\circ}C$ for 4 hours with 5wt% MgO showed the most dense structure with the grain size under 5${\mu}{\textrm}{m}$ and highest relative density of 98.2%.

• 한국세라믹학회지
• /
• 제30권2호
• /
• pp.123-130
• /
• 1993

Dispersed type Al2O3-SiC composite powders were synthesized from Al-isopropoxide (Al(i-OC3H7)3) and Si(OC2H5)4 precursors by hydrolysis of mixed alkoxides and carbothermal reaction method. The characteristics of the synthesized (dispersed type) Al2O3-SiC composite powders were investigated using XRD, SEM, TEM, BET and particle size analyzer. Carbothermal reaction to produce Al2O3-SiC composite was completed in 10h at 135$0^{\circ}C$ on 3~4㎤/s (0.21~0.28cm/s) of H2 flow rate and about 1/1 of carbon/oxides(=SiO2＋Al2O3) molar ratio. The synthesized powders were observed to have the mean particle size range of 0.4~1.26${\mu}{\textrm}{m}$ and showed finer particle size with increasing SiC content.

• 한국세라믹학회지
• /
• 제35권7호
• /
• pp.653-658
• /
• 1998

Zirconia coated NiO powders were prepared by the thermal hydrolysis of $Zro(NO_3)_2$.$6H_2O$ in a mixed solvent of alcohol and water. Amorphous zirconium hydroxide was uniformly coated on the surface of NiO powder with the thickness of 20nm. The $ZrO_2$ coating layer was crystallized to tetragonal $ZrO_2$ with the size of 40-60nm at $900^{\circ}C$. The coated NiO powder containing 15 vol% $ZrO_2$ was found to have a similar isoelectric point to that of the $ZrO_2$ The grain growth inhibition effect of the coated powders was superior to the mechanically mixed powders.

• 한국세라믹학회지
• /
• 제35권7호
• /
• pp.749-756
• /
• 1998

TiC-Ni and TiC-Ni-Mo cermet powders were produced by Self-propagating High temperature Synthesis (SHS) process. The cooling rate of synthesized powders were controlled by using the V-shaped copper jig and the carbide size decreased with increasing the cooling rate I. e decreasing the width of copper jig Round shape carbide particles were produced after SHS reaction in TiC-Ni as well as TiC-Ni-Mo powders. Local segregation of Mo rich phases was observed in SHS powder of TiC-Ni-Mo and the uneven dis-triobution of Mo promoted the faster growth rate of carbide particles during sintering compared to the same composition specimen with commercial TiC powder. Howogeneous microstructure of TiC-Ni-Mo cermet was obtained when the elemental Mo powder was mixed with the SHS powder of TiC-Ni.