• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.869-870
• /
• 2013

• Journal of the Korean Ceramic Society
• /
• v.52 no.1
• /
• pp.41-47
• /
• 2015

Celadon shards from Gangjin and Buan were analyzed for their color, chemistry and microstructures. They exhibited similar chromatic characteristics in a $CIEL^*a^*b^*$ analysis. All of the glazes assessed showed comparable compositional areas, while the bodies from Gangjin shards had higher $RO_2$ concentrations. A high degree of similarity was also noted in the microstructures of the glaze and bodies from both regions. Anorthite crystals appeared in the glaze layer, and phase separation behavior developed around these crystals. This may have been caused by the glaze chemistry and the sintering process given the lengthy heating and cooling time. A Raman analysis indicated higher isolated $SiO_4$ unit ($Q_0$) values for the Buan samples. This can stem from the higher firing temperature or the longer sintering process.

• Journal of the Korean Ceramic Society
• /
• v.53 no.5
• /
• pp.506-510
• /
• 2016

The eutectic melt of BaO-CuO flux is known to be a potential sintering aid for $Ba(Zr,Y)O_3$ (BZY) electrolyte for proton-conducting ceramic fuel cells (PCFCs). A density of BZY higher than 97% of theoretical density can be achieved via sintering at $1300^{\circ}C$ for 2 h using a flux composed of 28 mol% BaO and 72 mol% CuO. In the present study, chemical and structural evolution of BaO-CuO flux throughout the sintering process was investigated. An intermediate holding step at $1100^{\circ}C$ leads to formation of various impurity compounds such as $BaCuO_{1.977}$, $Ba_{0.92}Cu_{1.06}O_{2.28}$ and $Cu_{16}O_{14.15}$, which exhibit significantly larger unit cell volumes than the matrix. The presence of such secondary compounds with large lattice mismatch can potentially lead to mechanical failure. On the other hand, direct heating to the final sintering temperature produced CuO and $Cu_2O$ as secondary phases, whose unit cell volumes are close to that of the matrix. Therefore, the final composition of the flux is strongly affected by the thermal history, and a proper sintering schedule should be used to obtain the desired properties of the final product.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.822-828
• /
• 2002

Fabrication and electrical characterization of R. F. High-power unit capacitors were investigated to study on condition of fabrication processing for R. F. High-power unit capacitor and electrical characteristics according to addition of $ZrO_2$. The unit capacitors were fabricated using tape casting. The optimum mixture ratio of dielectrics and mixing binder for the slurry fabrication was 57.5∼60.0: 42.5∼40.0 wt%. The slurry viscosity was 4000∼5000 cps and casting state of green tape fabricated using these slurry was excellent. Optimum stacking was made by 200 kg/$cm^2$ pressure with 80$^{\circ}C$ heating. $ZrO_2$ was added to improve the electrical characteristics of unit capacitor, especially breakdown characteristics. The dielectric constant and loss factor of the unit condenser having different $ZrO_2$ amounts was not changed in the addition range of 1 to 5 wt%. Also, dielectric constant was not changed in the frequency range of 10 to 500 kHz. It was found that characteristics of resistance voltage was improved through the formation of $CaZrO_3$ and the reduction of particle size as about 3wt% $ZrO_2$ was added.

• The Korean Journal of Ceramics
• /
• v.1 no.1
• /
• pp.40-44
• /
• 1995

Ethylammonium-layered aluminosilicates intercalates were prepared by ion exchange reaction between the layered silicates with different layer changes density of 0.32∼0.41 e per unit formula and ethylammonium chloride. A kinetic study on the thermal deintercalation of the ethylammonium-layered silicate intercalates was carried out by range of 350℃ to 480℃ (heating rate of 10℃/min). Based on the Ozawa's method, the activation energies of the thermal deintercalation reaction were estimated as 171.2∼133.0 kJ/mol, which increase linearly with the layer charge densities.

• Tribology and Lubricants
• /
• v.22 no.6
• /
• pp.314-319
• /
• 2006

In this paper, the friction and wear characteristics of contact type sealing unit far a water turbine have been presented. The sealing unit for a small hydropower generation is to stop a leakage of circulating water from an outside of an impeller to an inside of a rolling bearing. The friction heating between a seal ring and a seal seat may radically increase a surface temperature in which increase a power loss and wear on the rubbing surface. The surface wear strongly affect to the seal life of a mechanical face seal. In this study, the hardness of a stainless steel in which is a heat-treated is 892.8 in Victors hardness and the hardness of silicone carbide of SiC is 714.1 in Victors hardness. The surface hardness of a heat-treated stainless steel is 25% high compared with that of a ceramic material of SiC. The contact modes of rubbing surfaces are a dry friction, a water film friction and a mixed friction that is contaminated by a dust, silt, and moistures, etc. These two factors of a contact rubbing modes and a material property are very important parameters on the tribological performance such as a friction and wear between a seal ring and a seal seat in primary sealing unit. The experimental result shows that the surface hardness of a seal material is very important on the friction coefficient and a wear volume. Thus, the results recommend higher hardness of a seal material, which may reduce a friction loss and increase a wear life of primary seal components.