• Geomechanics and Engineering
• /
• 제15권4호
• /
• pp.987-995
• /
• 2018

In this study, a relationship between small-strain shear modulus ($G_{max}$) and overconsolidation ratio (OCR) based on shear wave velocity ($V_S$) measurement was established to identify the stress history of centrifuge model ground. A centrifuge test was conducted in various centrifugal acceleration levels including loading and unloading sequences to cause various stress histories on centrifuge model ground. The $V_S$ and vertical effective stress were measured at each level of acceleration. Then, a sensitivity analysis was conducted using testing data to ensure the suitability of OCR function for the tested cohesionless soils and found that OCR can be estimated based on $V_S$ measurements irrespective of normally-consolidated or overconsolidated loading conditions. Finally, the developed $G_{max}$-OCR relationship was applied to centrifuge models constructed and tested under various induced stress-history conditions. Through a series of tests, it was concluded that the induced stress history on centrifuge model by compaction, g-level variation, and past overburden load can be analysed quantitatively, and it is convinced that the OCR evaluation technique will contribute to better interpret the centrifuge test results.

• 한국전산구조공학회논문집
• /
• 제29권1호
• /
• pp.1-8
• /
• 2016

본 논문에서는 원심식 대형 압축기 구동용 모터 베이스 프레임의 구조해석 및 콘크리트 타설에 따른 구조안전성 평가를 수행하였다. 먼저 모터 베이스 프레임에 적용되는 네 가지 하중조건에 따른 구조해석을 진행하고 최대 비틀림 에너지 이론 및 Mohr-Coulomb 이론을 통하여 구조안전성을 평가하였다. 구조해석 결과에서 취약한 구조안전성을 나타낸 연결부 등의 불연속적인 부분에서 발생하는 국부응력에 대하여 ASME VIII Div. 2에 따른 구조안전성 평가를 적용함으로써 좀 더 합리적으로 구조안전성 평가를 수행할 수 있었다. 또한, 모터 베이스 프레임 내부에 콘크리트 타설 및 미타설에 따른 구조해석 및 ASME 구조안전성 평가를 통하여 모터 베이스 프레임의 구조안전성을 정량적으로 비교하여 콘크리트 타설로 인한 구조 안전성의 향상을 확인하였다.

• BMB Reports
• /
• 제48권5호
• /
• pp.289-294
• /
• 2015

Caesalpinia sappan is a well-distributed plant that is cultivated in Southeast Asia, Africa, and the Americas. C. sappan has been used in Asian folk medicine and its extract has been shown to have pharmacological effects. Two homoisoflavonoids, sappanol and brazilin, were isolated from C. sappan by using centrifugal partition chromatography (CPC), and tested for protective effects against retinal cell death. The isolated homoisoflavonoids produced approximately 20-fold inhibition of N-retinylidene-N-retinyl-ethanolamine (A2E) photooxidation in a dose-dependent manner. Of the 2 compounds, brazilin showed better inhibition (197.93 ± 1.59 μM of IC₅₀). Cell viability tests and PI/Hoechst 33342 double staining method indicated that compared to the negative control, sappanol significantly attenuated H₂O₂-induced retinal death. The compounds significantly blunted the up-regulation of intracellular reactive oxygen species (ROS), and sappanol inhibited lipid peroxidation in a concentration-dependent manner. Thus, both compounds represent potential antioxidant treatments for retinal diseases. [BMB Reports 2015; 48(5): 289-294]

• 한국유체기계학회 논문집
• /
• 제19권2호
• /
• pp.21-26
• /
• 2016

The objective of present study is to assess the performance of the first stage compressor in a total 3-stage 5000 HP-level turbo compressor. CFD commercial code, CFX has been used to predict three-dimensional flow characteristics inside of the impeller. Shear Stress Transport (SST) model has been used to simulate turbulent flows through Reynolds-averaged Navier-Stokes (RANS) equations. Grid dependency has been also checked to get optimal grid distribution. Numerical results have been compared with the experimental test results to elucidate performance characteristics of the present compressor. In addition, flow characteristics of the impeller only have been studied for various blade configurations. Angular offset in leading edge of the blade has been selected for the optimal blade design. Performance characteristics in region of low mass flow rate and high pressure ratio between the impeller entrance and exit have been investigated for the selection of optimal blade design. Also, flow instability such as stall phenomena has been studied and anti-stall characteristics have been checked for various blade configurations in the operational window.

• 한국정밀공학회지
• /
• 제34권2호
• /
• pp.101-106
• /
• 2017

The chemical mechanical planarization (CMP) process combines the chemical effect of slurry with the mechanical effect of abrasive (slurry)-wafer-pads The slurry delivery system has a notable effect on polishing results, because the slurry distribution is changed by the supply method. Thus, the investigation of slurry pumps and nozzles with regard to the slurry delivery system becomes important. This paper investigated the effect of a centrifugal slurry pump on a spray nozzle system in terms of uniform slurry supply under a rotating copper (Cu) wafer, based on experimental results and computational fluid dynamics (CFD). In conventional tools, the slurry is unevenly and discontinuously supplied to the pad, due to a pulsed flow caused by the peristaltic pump and distributed in a narrow area by the tube nozzle. Adopting the proposed slurry delivery system provides a higher uniformity and lowered shear stress than usual methods. Therefore, the newly developed slurry delivery system can improve the CMP performance.

• 한국가스학회지
• /
• 제14권6호
• /
• pp.44-50
• /
• 2010

내진 평가에서 동적 해석이 필요한 원심펌프에 대하여, 시간 이력 해석에 비해 간편한 스펙트럼 해석을 이용하여, 진동 응답을 산출하였다. 유한요소법에 의하여 모드 해석을 하였으며, 모드 해석 결과에 입각하여 스펙트럼 해석을 수행하였다. 스펙트럼 해석에 의해 구해진 진동 응답은 시간 이력 해석의 결과보다 보수적으로 산출되어 안전하게 설계할 수 있음을 알 수 있었다. 본 연구에서의 펌프는 IEEE 344-1987에서 요구되는 조건에 따라 내진 구조 건전성이 평가 되었다. 각 부재의 최대 응력은 허용 응력이하로 산출되었으며, 펌프는 주어진 지진 입력에 대하여 요구되는 안전 조건을 구비하고 있음이 판명되었다.

• 한국소음진동공학회논문집
• /
• 제18권9호
• /
• pp.937-942
• /
• 2008

이 논문은 건설이 완료된 700MW급 발전소의 시운전 기간 중 주 급수펌프 임펠러에서 반복적으로 발생된 웨어링 이탈 및 고착, 슈라우드 손상 그리고 축 절단 등의 절손이 부분부하 조건에서 증폭되는 압력맥동과 연관이 있는 것으로 규명되었다.

• 한국정밀공학회지
• /
• 제21권8호
• /
• pp.97-105
• /
• 2004

The vertical roller mill is the important machine grinding and mixing various crude materials in the manufacturing process of portland cement. Table liner is one of grinding elements of vertical roller mill and is subjected to the cyclic bending stress by rollers and the centrifugal force by rotation of table. It demands $4{\times}10^7$ expense of life but has $4{\times}10^6~-8{\times}10^6$ cycle. It fractures at the edge of grinding path of outside roller The repair expense fur it amounts to 30% of total maintenance of vertical roller mill. Therefore, this study shows the fracture mechanism of table liner of vertical roller mill using HDM and fatigue analysis

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.489-493
• /
• 2000

Turbine blade has trouble of cracking at root region. Fracture surface of blade root is surveyed by SEM and AFM to clear relation between fracture mechanical parameter and surface parameter (striation width and surface roughness). Service stress is predicted by maximum height roughness $R_{max}$, on fractured surface and stress analysis on turbine blade. It is to thought that turbine blade is fractured by abnormal condition such as incorrect fittings between pin and pin hole but isn't fractured by normal service conditions such as steam pressure, centrifugal force and torsional force.

• 한국소음진동공학회논문집
• /
• 제16권9호
• /
• pp.982-989
• /
• 2006

The centrifugal force acting on a rotating disk creates the in-plane loads in radial and circumferential directions. Application of fiber reinforced composite materials to the rotating disk can satisfy the demand for the increment of its rotating speed. However, the existing researches have been confined to lamina disks. This paper deals with the stress and vibration analysis of rotating laminated composite disks. The maximum strain theory for failure criterion is applied to determine the strength of the laminate disk from which the maximum allowable speed is obtained. Dynamic equation is formulated in order to calculate the natural frequency and critical speed for rotating laminated disks. The Galerkin method is applied to obtain the series solution. The numerical results are given for the cross-ply laminated composite disks.