• The Journal of Engineering Geology
• /
• v.28 no.1
• /
• pp.61-67
• /
• 2018

Grouting is reinforcement or cutoff method which uses the hardening agent which is typically represented by portland cement and injected into the ground or the structure. When mixing the cement in powder form with water, the particles tend to cohere each other. Once they cohered, the particle size tends to become larger while injection efficiency becomes lower. This study, in a bid to reduce the cohesion of cement, the screen was set inside the grout mixer so that the cement particles are separated while vibrating them. To validate the effect of vibration screen, comparison test was conducted by using ordinary portland cement, slag cement and micro cement. Viscosity test, bleeding test and grain-size analysis indicated that the characteristics varied significantly after passing through the vibration filter. It is expected that the vibration filter installed inside the grout mixer will reduce the cement cohesion when mixing with water.

• International Journal of Highway Engineering
• /
• v.18 no.6
• /
• pp.105-113
• /
• 2016

OBJECTIVES : This study is to develop the optimum mixing proportions for cement concrete pavement with using recycled aggregates. METHODS : The mixture varied recycled coarse aggregates content from 50 % to 100 % to replace the natural coarse aggregates by weight. Tests for fundamental properties as a cement concrete pavement were conducted before and after hardening of the concrete. RESULTS : It was found that the variation in the amount of the recycled aggregate affected the compressive and flexural strength development, as well as the chloride ion penetration resistance. As the amount of the recycled aggregate content increased the compressive and flexural strength and the resistance to chloride ion penetration decreased. However, the resistance to freeze-thaw reaction was affected significantly. In addition, the gradation of the aggregate became worse and hence so did the coarseness factor as the recycled aggregate amount increased. CONCLUSIONS : The fundamental properties of the concrete with recycled aggregate does not seem to be appropriate when the recycled aggregate quality is not guaranteed up to a some level and its replacement ratio is over 50%. The optimized gradation of the aggregates should also be sought when the recycled aggregate is used for the cement concrete pavement materials.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.542-546
• /
• 2001

Converter slag has some compositional similarities to portland cement. But it has no hydration properties due to it's quite high concentrations of FeO(20-35%), MnO(4-6.5%). So it is needed to reduce the concentrations of iron and manganese of converter slag to use as cement additives by enhancing it's hydration properties. In this study, converter slag was modified it's composition by mixing of silica, alumina and quenched BF slag and reduced in induction furnace and quenched in running water. The hydraulic properties and structures of modified and quenched converter slag are significantly changed depend on the amount and kinds of additives. The addition of alumina up to 10% and BFQ slag up to 20% by weight on converter slag was effective to enhance the hydraulic properties of modified and quenched slag. The addition of reduced and quenched converter slag up to 20% by weight in replacement of portland cement in mixing of concrete mortar were shown higher compressive strength than 100% cement concrete mortar.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.225-226
• /
• 2021

Recently, environmental problems have emerged as a major issue all over the world due to an increase in carbon dioxide(CO₂). The amount of CO₂ generated during cement production accounts for 6% to 8% of domestic CO₂ emissions and a solution to reduce CO₂ emissions the construction industry is trying to use mineral admixtures to reduce cement. Since digestion has no firing process the advantage of it is that there is no air pollution to occur. In this study, we studied the compressive strength of binary non-cement mortar containing rice husk powder extracted from digestion by the ratio of 10%, 20%, 30%, 40%. As a result, the table flow was increased when the mixing rate of rice husk powder extracted from digestion was higher, and the highest compressive strength was shown when the rice husk powder extracted from digestion mixing rate was 10%.

• Journal of the Korean GEO-environmental Society
• /
• v.5 no.2
• /
• pp.15-21
• /
• 2004

This study is to develop simple solidifying agent to improve loose sand ground by admixing or injecting. This paper studied the optimum mixing ratio of micro cement, bentonite, chemistry admixture, plasticizer, accelerator for the optimum fluidity and strength. The optimum mixing ratio of micro cement and bentonite is 70% : 20%, the optimum ratio of the weight of rapid solidifying agent to the weight of total improved soil is about 8%, the optimum curing period is five days.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.5
• /
• pp.11-18
• /
• 2007

A laboratory investigation was conducted to characterize the flexural fatigue behavior of high performance fiber reinforced cement mortar. Five specimens for statics flexural test and fourteen specimens for the flexural fatigue test were made based on the fiber mixing ratio. Static flexural tests were firstly performed to obtain magnitudes of static failure loads and stress levels before flexural fatigue tests. The flexural fatigue behaviors were investigated based on the stress level and fiber mixing ratio. Also, the equations for the interrelation of the flexural fatigue stress levels with the number at loading cycle were proposed.

• Elastomers and Composites
• /
• v.34 no.5
• /
• pp.414-422
• /
• 1999

SBR, polyurethane and epoxy latex were separately blended with ethylene-vinyl acetate(EVA) emulsion In $0{\sim}50%$. EVA emulsion was not reacted with latexes in liquid phase and mixtures had good stroage stability. The viscosity of cement mixtures was elevated to 20,000cps in $0.5{\sim}2.0$ hours by mixing. The mixtures mixed with pigment represented high viscosity and showed higher viscosity as time goes by. Mixtures had higher hardness with mixing SBR than mixing epoxy or urethane. The hardness was suddenly increased over cement content 30%. showed pencil hardness $H{\sim}2H$ in $50{\sim}60%$. The increase of hardness in high solids was depended upon not only the condensation of latexs but also the coagulation and adhesion of cement particle.

• International Journal of Concrete Structures and Materials
• /
• v.2 no.2
• /
• pp.161-167
• /
• 2008

Optimization of concrete mixing system is very important for the production of quality mixture of concrete and requires very complicated, specialized knowledge as there are a variety of variables that influence the result. One of the methods of optimizing the concrete mixing system is to minimize the volume of cement paste which, in turn, means maximizing the volume of aggregate. The purpose of this study is to determine the minimum volume of cement paste used in the design of concrete mixture and to design the optimum concrete mixing system based on the fluidity of mortar and concrete. In determining the minimum volume of cement paste, experiments of mortar and concrete were performed based on their workability, material segregation and bleeding. Type of aggregate, granularity distribution and sand percentage were used as test parameters and measurements were taken of the distribution of granularity, usage of HRWRA, minimum volume of paste and drying shrinkage and compressive strength of concrete.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.1294-1300
• /
• 2009

Recently, excavations in highly congest urban area have been increased. For the excavations conducted in extremely narrow spaces, we have been developing a novel soil reinforcement system of temporary retaining walls by using deep cement mixing method. The developing method installs largerdiameter ($\Phi$=300~500mm) and shorter reinforcement blocks than previous reinforcement system for mobilizing friction with soils, therefore it has advantages of not only shortening the length of reinforcement system but also reducing the amount of reinforcement. In this study, we performed a numerical analysis of the new reinforcement system by using a commercial finite element program, and evaluated the behavior of the reinforced retaining wall system under various conditions of the length, the diameter, the spacing, and the angle of the reinforcement system.

• Journal of Powder Materials
• /
• v.27 no.6
• /
• pp.468-476
• /
• 2020

The bone cement used for vertebroplasty must be sufficiently injectable. The introduction of granules reduces the amount of liquid required for liquefaction, implying that higher fluidity is achieved with the same amount of liquid. By employing β-tricalcium phosphate granules with an average diameter of 50 ㎛, changes in injectability are observed based on the paste preparation route and granular fraction. To obtain acceptable injectability, phase separation must be suppressed during injection, and sufficient capillary pressure to combine powder and liquid must work evenly throughout the paste. To achieve this, the granules should be evenly distributed. Reduced injection rates are observed for dry mixing and excessive granular content, owing to phase separation. All these correspond to conditions under which the clustered granules weakened the capillary pressure. The injected ratio of the paste formed by wet mixing displayed an inverted U-type shift with the granular fraction. The mixture of granules and powder resulted in an increase in the solid volume fraction, and a decrease in the liquid limit. This resulted in the enhancement of the liquidity, owing to the added liquid. It is inferred that the addition of granules improves the injectability, provided that the capillary pressure in the paste is maintained.