• Proceedings of the Korea Concrete Institute Conference
• /
• 1991.10a
• /
• pp.99-106
• /
• 1991

Result of an experimental study on the manufacture, the mechanical properties and waterightness of pitch-based carbon fiber reinforced fly ash.cement composites are presented in this paper. The carbon fiber reinforced fly ash.cement composites using early strength cement, silica powder and a small amount of stylene butadiene rubber latex are prepared with carbon fiber, foaming agents and mixing conditions. As a result, the mechanical and plysical properties such as compresive, tensile and flectural strengths, watertightness and cement composites are improved by using a small amount of stylene butadiene rubber latex.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.275-280
• /
• 2002

To study of high volume fly -ash concrete replace cement and fine aggregate together. Proportion consideration economy cost and performance improve replacement high volume fly-ash. Experimentation study of high-strength which cement about fly-ash replacement maximum 50%Flash concrete tested slump, air contest, setting and Hardening concrete tested day of age 1, 3, 7, 28, 91 compression strength in underwater curing. Purpose of study is consultation materials in field that variety of fly ash replacement concrete mix proportion comparison and valuation.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.671-674
• /
• 1999

With increasing content of granulated blase furnace slag in cement, the content of capillary pores in the mortar decreases and later age strength of the concrete. Therefore, this provides greater reserves study is carried out to estimate frost resistance of high-strength concrete specimens with water cement ratios using blast-furnace slag. 1. Blast furnace concrete is comparatively more good frost resistance than normal concrete. 2. As the blast furnace slag increases, the quantity of pores with a radius of more than 30nanometer decreses.

• Journal of the Korean Ceramic Society
• /
• v.25 no.5
• /
• pp.455-464
• /
• 1988

Concrete used for radwaste container should have excellent properties such as mechanical strength, water-tightness, durability, etc. In order to improve such properties of ordinary portland cement concrete, superplasticizer, steel fiber, and/or epoxy resin were added to ordinary portland cement concrete respectively. Various concrete specimens were prepared and the physical properties of each concrete specimen were tested. From the experimental results, the properties of steel fiber and epoxy resin reinforced concrete were proved to be better qualified than others for low-and intermediate-level radwaste container.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2001.10a
• /
• pp.193-197
• /
• 2001

The growth in concrete structures repair has prompted major efforts to develop high early strength concrete. The internal or external restraint of thermal shrinkage movements could thus generate tensile stresses in concrete structures if it is used rapid setting repair concrete. Restrained shrinkage and thermal stresses could produce microcracks in concrete which increase its permeability and accelerate its long-term deterioration under weathering and load effects. This study aims at evaluation and increase of the engineering properties of high early strength concrete using regulated set cement.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.401-407
• /
• 1997

Objectives of this study is to investigate experimentally the behaviors of high strength concrete columns made with Belite cement by comparing with those of normal concrete columns. For the Belite high strength concrete columns and normal concrete columns having different core sizes, lateral reinforcement ratios and spacings, the experiment are performed and the behaviors of the columns like the confining effect are analyzed and discussed.

• Journal of the Korea Concrete Institute
• /
• v.14 no.5
• /
• pp.742-749
• /
• 2002

This study was performed to clarify the formation procedure of continuous voids in cellular concrete, and to examine the effect of a foaming agent on the manufacture of cellular concrete with continuous voids. By the experiments, it was determined that cellular concrete to be formed with continuous voids is influenced by temperature, viscosity and flowability of cement paste, and stability of air voids, and is formed in accordance with cohesion of air voids. It was also found that separate voids are formed at an added amount of air voids corresponding to 2 ％ or less of the amount of cement, whereas an antifoaming phenomenon occurs when the added amount of air voids exceeds 9 ％ of the amount of cement. In products with respective cement fineness of 3,000, 6,000, and 8,000㎠/g, a higher compressive strength was exhibited at a higher cement fineness. The continuous void ratio depending on a variation in fineness was 38 ％, 52 ％, and 22 ％ in those products, respectively. That is, a highest continuous void ratio was exhibited at a cement fineness of 6,000㎠/g. When the water-cement ratio was reduced from 45％ to 25％, the compressive strength of the cellular concrete was increased from 15 kgf/㎠ to 20 kgf/㎠ Thus, the reduction in water-cement ratio was effective in achieving an increase in strength without any variation in the specific gravity of the cellular concrete.

• Journal of the Korea Concrete Institute
• /
• v.18 no.6 s.96
• /
• pp.769-776
• /
• 2006

Recently, owing to the development of industry and the improvement of building techniques, concrete structures are becoming larger and higher. In hardening of these large connote structures, the heat of hydration gives rise to considerable thermal stress depending on the size and environmental condition of concrete, which might cause thermal cracking. Especially, the crack may cause severe damage to the safety and the durability of concrete structure. This study investigates the thermal properties of concrete according to several binder conditions, such as OPC, Belite rich cement(BRC), slag cement(SC), blast furnace slag(B) added cement fly ash(F) added cement and blast-furnace-slag and fly ash added cement. As a result of this study, the properly of concrete is most better BRC than others, and fly ash(25%) added cement and BFS(35%)-fly ash(15%) added cement gets superior effect in the control of heat hydration. But synthetically considered properties of concrete, workablity, strength heat hydration, etc, it is more effective to use mineral admixture. Especially, to be used Blast Furnace slag is more effective.

• Journal of the Korea Concrete Institute
• /
• v.20 no.6
• /
• pp.797-807
• /
• 2008

For this study, the semi-adiabatic temperature rising test is accomplished by using ternary system cement (OPC, BFS, FA) reducing temperature crack. Two tests are conducted; one is for the paste test, and the other is for the concrete test. As the results of paste tests, using fly ash is better to reduce hydration temperature than doing blast furnace slag. In the case of the paste mixed ternary system cement, the more fly ash is mixed and the less blast furnace slag is used, the lower the temperature is. The less the mixture ratio of blast furnace slag is and the more the mixture ratio of fly ash is, the later the temperature rising velocity and descending velocity are. Besides, the temperature is lower if water/binder ratio is high. The use of ternary system cement has the retardation effect of temperature rising because the time to reach the maximum temperature is in the order of OPC100, binary system cement, and ternary system cement. From the test, the maximum temperature of concrete used ternary system cement is $8{\sim}11^{\circ}C$ lower than that of concrete used OPC100. Moreover, temperatures rising velocity and descending velocity of ternary system cement range $47{\sim}51%$ and $37{\sim}42%$ compared with OPC100. The specimen of concrete shows remarkable low internal temperature and slow temperature rising velocity and descending velocity compared with the specimen of paste because it is that temperature loss of concrete is much more than paste specimen according to aggregates.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.3
• /
• pp.89-96
• /
• 2013

Now-a-days, a manhole adopted since the late 1990s and produced using the polymer concrete has widely used due to the various benefits. While entering the High oil prices times, however, and with the price increase of the petrochemical materials, the cost of manufacture of polymer concrete was elevated and the resulting polymer concrete's weakness is being put on. Accordingly, the development of economic cement concrete manholes, which can replace the outstanding bending strength of manhole made of high-price polymer concrete, has been required. In this study, based on the cement technology of fast hardening armorphous calcium aluminate (ACA), by minimizing the amount of cement using the industrial byproducts, to develop the eco-friendly high-toughness concrete manhole, which can reduce $CO_2$ reduction, was intended. As the results, the cement concrete manhole, which economic, eco-friend, and meeting the performance requirements, was developed.