• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.58.1-58.1
• /
• 2010

Stainless Steel의 유연한 기판을 사용하여 ZnO:Al/Ag의 후면전극에서 Ag 증착 실험조건 변화를 통해서 light trapping을 개선한 n-i-p 구조의 플렉서블 미세결정질 실리콘 박막 태양전지를 제작하였다. 실험 방법으로 마그네트론 스퍼터를 사용하여 Stainless Steel 기판 위에 ZnO:Al/Ag를 증착하여 후면전극으로 사용되는 back reflector를 제작하였으며 그 위에 미세결정질 실리콘 박막을 증착하였다. Back reflector에서 Ag 박막의 증착 온도가 증가할수록 표면결정 성장으로 roughness가 증가하여 반사도를 증가하였다. 또한, Ag 박막 증착 두께와 압력 변화에 따른 광학적 특성변화를 Atomic Force Microscope(AFM), Scanning Electron Microscopy(SEM),UV-visible-nIR spectrometry로 조사하여 최적의 조건을 찾았으며 개선된 back reflector의 특성이 n-i-p 구조의 플렉서블 미세결정질 실리콘 박막 태양전지에 적용하여 light trapping의 증가가 태양전지에서 광학적인 특성 변화 및 효율 향상에 영향을 주는지 Photo IV와 EQE(External Quantum Efficiency)를 통하여 조사하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.594-594
• /
• 2012

Al doped ZnO (AZO) thin films were deposited on textured glass substrate by magnetron sputtering method. Also, AZO films on textured glass were etched by hydrochloric acid (HCl). Average thickness of etched AZO films are 90 nm. We observed morphology of AZO film by AFM with various etchant concentration and etching time. Etched AZO films have low resistivity and high haze. The surface RMS roughness of AZO film was increased from 53.8 nm to 84.5 nm. The haze ratio was also enhanced in above 700 nm of wavelength due to light trapping effect was increased by rough AZO surface. The etched AZO films on textured glass are applicable to fabricate solar cell.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.9
• /
• pp.634-640
• /
• 1999

Resonance radiation trapping has a great influence on the characteristics of vacuum ultraviolet(VUV) photon emissions in AC PDP cell. We calculate the spatial andspectral distributions of VUV photons, which are radiated by excited Xe in AC PDP cell by Monte Carlo method. Especially a dip in the spectrum at center frequency is discovered both in simulation and in experiment. We give a physical explanation of this phenomenon by the concept of frequency-dependent mean free path of VUV photons.

• Proceedings of the PSK Conference
• /
• 2003.10b
• /
• pp.160.3-161
• /
• 2003

Aldehyde and active form of free oxygen produced in alcohol metabolism in liver are the cause of liver cell damage. The main system of alcohol metabolism is composed of alcohol dehydrogenase(ADH), aldehyde dehydrogenase(ALDH) and cytochrome P4502E1. Alcohol dehydrogenase is reversible in alcohol metabolism. To block the backward reaction and enhance alcohol oxidation, acetaldehyde trapping agents were assayed. The assay was carried out by measuring decreasing NADH at 340nm, using acetaldcehyde and NADH as substrate and coenzyme respectively. (omitted)

• Current Photovoltaic Research
• /
• v.4 no.3
• /
• pp.119-123
• /
• 2016

We discussed various cover glass substrates available for photovoltaic (PV) modules, and investigated the fabrication methods of light trapping structures for the efficiency enhancement of PV modules: wet and dry etching or laser and direct patternings. We also introduced the analysis of haze at etched glass surfaces as a function of wavelength and also presented a anti-reflection coating technology for PV module.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.3
• /
• pp.19-24
• /
• 2019

In this study, the Ag nano-dots structure was applied to the textured wafer surface to improve the light trapping effect of crystalline silicon solar cell. The Ag nano-dots structure was formed by the annealing of Ag thin film. Ag thin film deposition was performed using a thermal evaporator. The effect of light trapping was compared and analyzed through light reflectance measurements. The optimization process of the Ag nano-dots structure was made by varying the thickness of Ag thin film, the annealing temperature and time. The thickness of Ag thin films was in the range of 5 ~ 20 nm. The annealing temperature was in the range of 450~650℃ and the annealing time was in the range of 30 ~ 60 minutes. As a result, the light reflectance of 10 nm Ag thin film annealed at 650℃ for 30 minutes showed the lowest value of about 9.67%. This is a value that is about 3.37% lower than the light reflectance of the sample that has undergone only the texturing process. Finally, the change of the light reflectance by the HF treatment of the sample on which the Ag nano-dots structure was formed was investigated. The HF treatment time was in the range of 0 ~ 120 seconds. As a result, the light reflectance decreased by about 0.41% due to the HF treatment for 75 seconds.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.4
• /
• pp.12-17
• /
• 2019

In this study, the Ag nano-dots structure and silicon nitride film were applied to the textured wafer surface to improve the light trapping effect of mono-crystalline silicon solar cell. Ag nano-dots structure was formed by performing a heat treatment for 30 minutes at 650℃ after the deposition of 10nm Ag thin film. Ag thin film deposition was performed using a thermal evaporator. The silicon nitride film was deposited by a Hot-wire chemical vapor deposition. The effect of light trapping was compared and analyzed through light reflectance measurements. Experimental results showed that the reflectivity increased by 0.5 ~ 1% under all nitride thickness conditions when Ag nano-dots structure was formed before nitride film deposition. In addition, when the Ag nano-dots structure is formed after deposition of the silicon nitride film, the reflectance is increased in the nitride film condition of 70 nm or more. When the HF treatment was performed for 60 seconds to improve the Ag nano-dot structure, the overall reflectance was improved, and the reflectance was 0.15% lower than that of the silicon nitride film-only sample at 90 nm silicon nitride film condition.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.90.2-90.2
• /
• 2010

The crystalline silicon solar cells have been optical losses. but it can be reduced using light trapping by texture structure and anti-reflection coating. The high reflective index of crystalline silicon at solar wavelengths(400nm~1000nm) creates large reflection losses that must be compensated for by applying anti-reflection coating. In this study, the use of porous silicon(PSi) as an active material in a solar cell to take advantage of light trapping and blue-harvesting photoluminescence effect. Porous silicon is form by anodization and can be obtained in an electrolyte with hydrofluoric. We expect our research can results approaching to lower than 10% of several reflectance by porous silicon solar cells.

• Current Photovoltaic Research
• /
• v.5 no.3
• /
• pp.75-82
• /
• 2017

High efficiency thin film solar cells require an absorber layer with high absorption and low defect, a transparent conductive oxide (TCO) film with high transmittance of over 80% and a high conductivity. Furthermore, light can be captured through the glass substrate and sent to the light absorbing layer to improve the efficiency. In this paper, morphology formation on the surface of glass substrate was investigated by using HF, mainly classified as random etching and periodic etching. We discussed about the etch mechanism, etch rate and hard mask materials, and periodic light trapping structure.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.65-69
• /
• 2017

This paper presents a Technology-CAD (TCAD) simulation of the characteristics of crystalline Si pillar array solar cells. The junction depth and the surface concentration of the solar cells were optimized to obtain the targeted sheet resistance of the emitter region. The diffusion model was determined by calibrating the emitter doping profile of the microscale silicon pillars. The dimension parameters determining the pillar shape, such as width, height, and spacing were varied within a simulation window from ${\sim}2{\mu}m$ to $5{\mu}m$. The simulation showed that increasing pillar width (or diameter) and spacing resulted in the decrease of current density due to surface area loss, light trapping loss, and high reflectance. Although increasing pillar height might improve the chances of light trapping, the recombination loss due to the increase in the carrier's transfer length canceled out the positive effect to the photo-generation component of the current. The silicon pillars were experimentally formed by photoresist patterning and electroless etching. The laboratory results of a fabricated Si pillar solar cell showed the efficiency and the fill factor to be close to the simulation results.