• Journal of the Korean Electrochemical Society
• /
• v.12 no.4
• /
• pp.342-348
• /
• 2009

Zn/Air secondary batteries are high energy density type and environment-friendly. Also, they have safer properties than batteries of other type by low manufacturing cost and using the electrolyte solution. But, they have a weak concerning large output discharge. Oxygen evolution reaction(OER) and oxgen reduction reaction(ORR) in aqueous solution make a result of a decrease of cell efficiency and life span. Therefore, to minimize the voltage drop from between OCV and charge/discharge voltage is key point. The problem should be solved through developing catalysts of high efficiency. In this study, we synthesized $Pr_{1-x}(Sr,\;Ca)_x\;CoO_3$ powders by citric method and then measured physical characteristics of each powder by XRD, SEM, TGA etc. We examined its electrochemical properties by the cathodic polarization, anodic polarization and cyclic voltammogram. We achieved results that new catalysts showed better performances than existing $La_{1-x}Sr_xCoO_3$, $La_{1-x}Ca_xCoO_3$, ect. catalysts prepared in our lab.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.40 no.7
• /
• pp.1025-1031
• /
• 2011

The objective of this study was to compare the performances of conventional microbiological media used in isolation of Shigella spp. from foods. Total of six selective media, including MacConkey agar (MAC), Salmonella Shigella agar (SSA), desoxycholate citrate agar (DCA), xylose lysine desoxycholate agar (XLD), hektoen enteric agar (HEA), and CHROMagar, were tested. MAC showed almost the same colony numbers as compared to tryptic soy agar (TSA) while DCA showed significantly lower colony numbers when cultivated Shigella spp. was counted in each medium. In a food recovery test with beef, pork and shrimp, S. sonnei recovered well on CHROMagar (p<0.05). With lettuce and cabbage, S. sonnei displayed significantly significant recovery (p<0.05) on SSA in comparison with other selective media. Heat-injured cells recovered well on MAC and SSA. In a specificity test using Enterobacteriaceae strains, HEA was identified as having the highest specificity among the tested media. However, Morganella spp. could not be differentiated from Shigella spp. on any of the tested selective media. Shigella spp. precluded the possibility of isolation from foods by a single 'best' selective medium. Consequently, a combination of complementary selective media or selection of appropriate media according to cell conditions must be considered for comprehensive isolation.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.149-152
• /
• 2012

$Cu(In,Ga)Se_2$ (CIGS) is one of the most promising photovoltaic materials because of large conversion efficiency which has been achieved with an optimum Ga/(In+Ga) composition in $CuIn_{1-x}Ga_xSe_2$ (X~0.3). The Ga/(In+Ga) content is important to determine band gap, solar cell performances and carrier behaviors at grain boundary (GB). Effects of Ga/(In+Ga) content on physical properties of the CIGS layers have been extensively studied. In previous research, it is reported that GB is not recombination center of CIGS thin-film solar cells. However, GB recombination and electron-hole pair behavior studies are still lacking, especially influence of with different X on CIGS thin-films. We obtained the GB surface potential, local current and I-V characteristic of different X (00.7 while X~0.3 showed higher potential than 100 mV on GBs. Higher potential on GBs appears positive band bending. It can decrease recombination loss because of carrier separation. Therefore, we suggest recombination and electron-hole behaviors at GBs depending on composition of X.

• Journal of the Korean Ceramic Society
• /
• v.43 no.6 s.289
• /
• pp.369-375
• /
• 2006

[ $(Ba_{0.5}Sr_{0.5})_{0.99}Co_{x}Fe_{1-x}O_{3-{\delta}}$ ] [x=0.8, 0.2](BSCF) powders were synthesized by a Glycine-Nitrate Process (GNP) and the electrochemical performance of the BSCF cathode on a scandia stabilized zirconia, $[(Sc_{2}O_3)_{0.11}(ZrO_2)_{0.89}]-1Al_{2}O_3$ was investigated. In order to prevent unfavorable solid-state reactions between the cathode and zirconia electrolyte, a GDC ($Gd_{0.1}Ce_{0.9}O_{2-{delta}}$) buffer layer was applied on ScSZ. The BSCF (x = 0.8) cathode formed on GDC(Buffer)/ScSZ(Disk) showed poor electrochemical property, because the BSCF cathode layer peeled off after the heat-treatment. On the other hand, there were no delamination or peel off between the BSCF and GDC buffer layer, and the BSCF (x = 0.2) cathode exhibited fairly good electrochemical performances. It was considered that the observed phenomenon was associated with the thermal expansion mismatch between the cathode and buffer layer. The ohmic resistance of the double layer cathode was slightly lower than that of the single layer BSCF cathode due to the incorporation of platinum particle into the BSCF second layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.490.2-490.2
• /
• 2014

Since the general solar cells accept sun light at the front side, excluding the electrode area, electrons move from the emitter to the front electrode and start to collect at the grid edge. Thus the edge of gridline can be important for electrical properties of screen-printed silicon solar cells. In this study, the improvement of electrical properties in screen-printed crystalline silicon solar cells by contact treatment of grid edge was investigated. The samples with $60{\Omega}/{\square}$ and $70{\Omega}/{\square}$ emitter were prepared. After front side of samples was deposited by SiNx commercial Ag paste and Al paste were printed at front side and rear side respectively. Each sample was co-fired between $670^{\circ}C$ and $780^{\circ}C$ in the rapid thermal processing (RTP). After the firing process, the cells were dipped in 2.5% hydrofluoric acid (HF) at room temperature for various times under 60 seconds and then rinsed in deionized water. (This is called "contact treatment") After dipping in HF for a certain period, the samples from each firing condition were compared by measurement. Cell performances were measured by Suns-Voc, solar simulator, the transfer length method and a field emission scanning electron microscope. According to HF treatment, once the thin glass layer at the grid edge was etched, the current transport was changed from tunneling via Ag colloids in the glass layer to direct transport via Ag colloids between the Ag bulk and the emitter. Thus, the transfer length as well as the specific contact resistance decreased. For more details a model of the current path was proposed to explain the effect of HF treatment at the edge of the Ag grid. It is expected that HF treatment may help to improve the contact of high sheet-resistance emitter as well as the contact of a high specific contact resistance.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.4C
• /
• pp.341-348
• /
• 2009

In this paper, we propose a grouping technique for the SDD(Synchronous Digital Duplexing) based on OFDMA(Orthogonal Frequency Division Multiple Access). The SDD has advantages of increasing data efficiency and flexibility of resource since SDD can transmit uplink signals and downlink signals simultaneously by using mutual time information and mutual channel information, obtained during mutual ranging process. However, the SDD has a disadvantage of requiring additional CS to maintain orthogonality of OFDMA symbols when the sum of mutual time difference and mutual channel length between AP(access point) and SS(subscriber station) or among SSs are larger than CP length. In order to minimize the length of CS for the case of requiring additional CS in SDD, we proposes a grouping technique which controls transmit timing and receive timing of AP and SS in a cell by classifying them into groups. Performances of the proposed grouping technique are evaluated by computer simulation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.478-478
• /
• 2012

Recently, there are many researches in order to increase the deposition rate (D/R) and improve film uniformity and quality in the deposition of microcrystalline silicon thin film. These two factors are the most important issues in the fabrication of the thin film solar cell, and for the purpose of that, several process conditions, including the large area electrode (more than 1.1 X 1.3 (m2)), higher pressure (1 ~ 10 (Torr)), and very high frequency regime (VHF, 40 ~ 100 (MHz)), have been needed. But, in the case of large-area capacitively coupled discharges (CCP) driven at frequencies higher than the usual RF (13.56 (MHz)) frequency, the standing wave and skin effects should be the critical problems for obtaining the good plasma uniformity, and the ion damage on the thin film layer due to the high voltage between the substrate and the bulk plasma might cause the defects which degrade the film quality. In this study, we will propose the new concept of the large-area multi-electrode (a new multi-electrode concept for the large-area plasma source), which consists of a series of electrodes and grounds arranged by turns. The experimental results with this new electrode showed the processing performances of high D/R (1 ~ 2 (nm/sec)), controllable crystallinity (~70% and controllable), and good uniformity (less than 10%) at the conditions of the relatively high frequency of 40 MHz in the large-area electrode of 280 X 540 mm2. And, we also observed the SEM images of the deposited thin film at the conditions of peeling, normal microcrystalline, and powder formation, and discussed the mechanisms of the crystal formation and voids generation in the film in order to try the enhancement of the film quality compared to the cases of normal VHF capacitive discharges. Also, we will discuss the relation between the processing parameters (including gap length between electrode and substrate, operating pressure) and the processing results (D/R and crystallinity) with the process condition map for ${\mu}c$-Si:H formation at a fixed input power and gas flow rate. Finally, we will discuss the potential of the multi-electrode of the 3.5G-class large-area plasma processing (650 X 550 (mm2) to the possibility of the expansion of the new electrode concept to 8G class large-area plasma processing and the additional issues in order to improve the process efficiency.

• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1192-1199
• /
• 1999

The morphology changes of cadmium hydroxide into ${\gamma}$ phase by eletrolytes were carried out to improve the high rate charge and discharge efficiency of pasted cadmium electrodes. KOH solutions with different concentrations of NaOH were used as eletrolytes. It was found that the utilization of active material of cadmium electrode was the best in an electrolyte with 1.82 M NaOH. The amount of ${\gamma}-Cd(OH)_2$ increased in proportion to the concentration of NaOH. The surface area measurement showed that an active material which contained mainly ${\gamma}-Cd(OH)_2$ had a higher specific surface area than an active material of ${\beta}-Cd(OH)_2$. In a sealed cell, the discharge capacity was improved at high rate charge and discharge (1.0 C, 2.0 C) by using an electrolyte with NaOH. Furthermore, these improved performances were maintained up to 500 cycles at 1.0 C rate charge and discharge cycles.

• Applied Chemistry for Engineering
• /
• v.19 no.4
• /
• pp.407-412
• /
• 2008

As an activation procedure, in this study, the oxidation treatment of needle cokes with a dilute nitric acid and sodium chlorate $(NaClO_3)$, combined with heat treatment, was attempted. The structures of acid-treated and pyrolyzed coke were examined with XRD, FESEM, elemental analyzer, BET, and Raman spectroscopy. The behavior of double layer capacitance was investigated with the analysis of charge and discharge. The structure of needle coke treated with acid was revealed to a single phase of (001) diffraction peak after 24 h. On the other hand, thecoke oxidized by heat treatment was reduced to a graphite structure of (002) at $300^{\circ}C$. The distorted graphene layer structure, derived from the process of oxidation and reduction of the inter-layer, makes the pores by the electric field activation at the first charge, and generates the double layer capacitance from the second charge. The cell using pyrolyzed coke with 24 h acid treatment and $300^{\circ}C$ heat treatment exhibited the maximum capacitance per weight and volume of 33 F/g and 30 F/mL at the two-electrode system in the potential range of 0~2.5 V.

• Journal of Animal Science and Technology
• /
• v.53 no.2
• /
• pp.139-146
• /
• 2011

This study was carried out to investigated astaxanthin producing "Xanthophyllomyces dendrohous" on growth performances and meat quality in ducks. A total of 450 ducks (cheribery) were allotted into 3 groups. The three groups were control (commercial feed), treatment 1 (0.1% feed additives), and treatment 2 (0.2% feed additives). Each group had 3 replicates. Viable cell number of "Xanthophyllomyces dendrohous" is $1.0{\times}10^8$ cfu/g. Growth performance carried out during 39 days. Average weight gain was significantly higher (p<0.05) in treatment 2 than that of control. Feed conversion was significantly lower (p<0.05) in treatment 1 and 2 than that of control. The results of nutrients composition analysis of duck meat showed that treatment 1 and 2 had significantly lower (p<0.05) fat and cholesterol levels. Water holding capacity showed significantly higher (p<0.05) value than that of control. Both treatment groups showed lower (p<0.05) value than control in drip loss and shear force. Control showed higher unsaturated fatty acids(palmitic acid, stearic acid) content than treatment 1 and 2. Treatment 1 and 2 showed significantly lower (p<0.05) saturated fatty acids (oleic acid, linoleic acid) levels than control. These results suggested that the supplementation of feed additives containing "Xanthophyllomyces dendrohous" might be used effectively for inproving productivity and meat quality of ducks.