• Transactions of the Korean hydrogen and new energy society
• /
• v.13 no.3
• /
• pp.224-232
• /
• 2002

CdS-$TiO_2$ nano-composite sol was prepared by the sol-gel method in organic solvents at room temperature and further hydrothermal treatment at various temperatures to control the physical properties of the primary particles. Again, CdS-$TiO_2$ composite particulate films were made by casting CdS-$TiO_2$ sols onto $F:SnO_2$ conducting glass and then heat-treatment at $400^{\circ}C$. Physical properties of these 61ms were further controlled by the surface treatment with $TiCl_4$, aqueous solution. The photo currents and hydrogen production rates measured under the experimental conditions varied according to the $CdS/[CdS+TiO_2]$ mole ratio and the mixed-sol preparation method. For $CdS-TiO_2$ composite sols prepared in IPA, CdS particles were homogeneously surrounded by $TiO_2$ particles. Also, the surface treatment with $TiCl_4$ aqueous solution caused a considerable improvement in the photocatalytic activity, probably as a result of close contacts between the primary particles by the etching effect of $TiCl_4$. It was found that the photoelectrochemical performance of these particulate films could be effectively enhanced by this approach.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1996.11a
• /
• pp.105-105
• /
• 1996

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.75-77
• /
• 1987

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.519-521
• /
• 1987

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2008.05a
• /
• pp.28.2-28.2
• /
• 2008

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.11a
• /
• pp.49-54
• /
• 1992

Devices of ITO/CdS/CdTe/Te/Al were prepared by Electron-Beam deposition under a vacuum of $7{\times}10^{-6}$[torr]. Optical, Electrical, Structural and Photovoltaic properties of thin film CdS/CdTe at substrate. temperature 300~500[$^{\circ}C$] were also investigated, The structure of CdTe films deposited was of the zincblende type a preferential orientation of the (111) plane parallel to the substrate, the CdTe dark resistivity was about $10^6[{\Omega}cm]$. The conversion, efficiency of the cell increased with increasing substrate temperature. The best-fabricated Cell was a conversion efficiency of 9.1[%].

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.101-102
• /
• 2005

Cadmium telluride (CdTe) films have been prepared on Coming 7059 glass, molybdemium (Mo), and polyimide (PI) substrates by r.f. magnetron sputtering technique. The influence of the sputter pressure on the structural and optical properties of these films was evaluated. In addition, a comparison of the properties of the films deposited on different substrates was performed.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.2
• /
• pp.183-191
• /
• 1990

Polycrystalline CdS film have been prepared by coating a slurry constiting of CdS, CdCl2, various amount of InCl3 and propylene glycol on glass substrate and by sintering in a nitrogen atmosphere, and their sintering behaviors, electrical properties and optical properties have been investigated. As the amount of InCl3 increases, the enhancing effect of CdCl2 on sistering decreses resulting in a sharp decrease in optical transmittance and an increase in electrical resistivity. The carrier concentration is almost independent of InCl3 added due to the occurrence of chlorine doping and to the compensating effect of indium dopant. Microstructure an optical properties of CdS film, which contain CdCl2 and InCl3 before sintering, can be improved by sintering in a sealed boat.

• Korean Journal of Materials Research
• /
• v.9 no.2
• /
• pp.173-180
• /
• 1999

Thermally evaporated ZnTe films were investigated as a back contact material for CdS/CdTe solar cells. Two deposition methods, coevaporation and double-layer methods, were used for Cu doping in ZnTe films. ZnTe layers (0.2$\mu\textrm{m}$ thick) were deposited either on glass or on CdS/CdTe substrates without intentional heating of the substrates. Post-deposition annealing was performed at 200,300 and $400^{\circ}C$ for 3,6 and 9 minutes, respectively. Band gap of 2.2eV was measured for both undoped and doped films and a slight change in the shape of absorption spectra was observed in Cu-doped samples after annealing at $400^{\circ}C$. The resistivity of as-deposited ZnTe decreased from 10\ulcorner~10\ulcornerΩcm down to 10\ulcornerΩcm as Cu concentration increased from 0 to 14 at.%. There was not a noticeable change in less of annealing temperature up to $300^{\circ}C$ whereas films annealed at $400^{\circ}C$ revealed hexagonal (101) orientations as well. Some of Cu-doped ZnTe revealed x-ray diffraction (XRD) peaks related with Cu\ulcornerTe(x=1.75~2). Grain growth was observed from about 20nm in as-deposited films to 50nm after annealing at $400^{\circ}C$ by scanning electron microscopy (SEM). Cu distribution in ZnTe films was not uniform according to Auger electron spectroscopy (AES) measurements.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.456-456
• /
• 2008

In the past few years, the deposition and characterization of cadmium sulfide semiconducting thin films has received a considerable amount of interest due to their potential application in the area of electronic and opto-electronic devices fabrications. Polycrystalline CdS thin films posses good optical transmittance, wide band-gap and electrical properties makes it as one of the ideal material for their application to solar cell fabrication. Cadmium sulfate thin films were deposited by the chemical bath deposition method using tartaric acid and triethanolamine as a complexing agent. Deposition parameters such as pH, temperature, deposition time and concentration of the reactant species were optimized so as to obtain reflecting, good adherent uniform thin films on the glass substrate. Reaction mechanism of the thin film formation is also reported. The crystallographic structure and the crystallite size were studied by the X-ray diffraction pattern. The optical band-gap of deposited film is identified by measuring the transmittance in the visible region. Temperature dependence of resistivity confirmed the semiconducting behavior of the film. Scanning electron micrographs (SEM) showed the presence of grain particles of size 50 nm.