• Special Issue of the Society of Naval Architects of Korea
• /
• 2005.06a
• /
• pp.44-50
• /
• 2005

Since a cavitation pattern in model scale can be different from that in full scale, it has been highly demanded to measure a fluctuating pressure induced by propeller in full scale. For the verification of the cavitation test for 105K lanker in the large cavitation tunnel in Samsung Ship Model Basin(SSMB), an effective pressure fluctuation measurement system was developed and a series of full scale measurements was carried out. These results were compared with those of cavitation tests in SSMB. The measured results in full scale gave good agreements to those in model tests. The fluctuating pressure at $2^{nd}$ blade frequency in full scale seems to be highly dependent upon tip loading.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.791-796
• /
• 2000

The cavitation-induced fluctuating pressure of the container ship named "Sydney Express" is measured in Samsung Large Cavitation Tunnel(SCAT). In the measurements, a complete ship model is employed. The effects of thrust coefficient and cavitation number on cavity pattern and cavitation-induced fluctuating pressure were investigated experimentally. It is demonstrated that the fluctuating pressure coefficient is very sensitive to the cavitation number. The results of cavitation and pressure fluctuations are compared with those of ITTC and HSVA, which shows fairly good agreement. It is exhibited that the removal of rudder can significantly change the loading condition of a propeller, and can reduce the fluctuating pressure coefficient almost by half.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.11a
• /
• pp.185-187
• /
• 2009

A density based method with homogeneous cavitation model to investigate cavitation-bubble collapsing behavior is proposed and applied to bubble-shock interaction problems. By applying this method, cylindrical bubbles located in the liquid and incident liquid shock wave are computed. Bubble collapsing behavior, shock-bubble interaction and shock transmission/reflection pattern are investigated.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.32 no.3
• /
• pp.302-309
• /
• 1996

Cavitation erosion-corrosion implies damage to materials due to the shock pressure or shock wave that results when bubbles form and collapse at a metal surface within a liquid. If the liquids corrosive to the material, a condition typically encountered in industry, the component materials may suffer serious damage by a combination of mechanical and electrochemical attack. To suppress cavitation erosion as well as cavitation erosion-corrosion to hydraulic equipments, innovations such as the improvement in the geometric design of the equipment or the selection of suitably resistant construction materials are necessary. This study was tested by using the piezoelectric vibrator with 20kHz, 24${\mu}$m for cavitation generation. And also, the vibratory cavitation erosion-corrosion tests on commercial mild steel SS41were carried out. We carefully observed the erosion pattern and surface photography. The geometrical mechanism of pit growth, which is to be likely these processing; shallow typelongrightarrowundercut typelongrightarrowwide shallow type.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.3
• /
• pp.363-371
• /
• 2003

This study is mainly concerned with phenomenon of cavitation-erosion on the several materials and corrosive liquids which were applied with vibrator(suggested by ASTM G 32, 20KHz, 50$mu extrm{m}$). The maximum erosion rate by cavitation erosion in both of distilled water and sea water appeared to be proportioned to their hardness and tensile strength. Cavitation weight loss and rate of cast iron in sea water condition were greater(approximately 3 times) than that in distilled water condition, however in case of stainless steel and brass the cavitation weight loss of composite materials were not so different in both of their conditions. Cavitation weight loss of composite materials were shown as below on this test, Duratough DL : Weight loss in sea-water condition were greater (approximately 2.3 times) than it's distilled water condition. The main tendency of cavitation erosion for metals appeared that small damaged holes causing by cavitation erosion was observed with radial pattern. On the other hand, the tendency for composites appeared that small damaged holes were observed randomly.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.227-233
• /
• 1999

This study is mainly concerned with phenomenon of cavitation-erosion on the several materials and corrosive liquids which were applied with vibrator (suggested by ASTM G-32, 20KHZ, 24{$mu}m$).The main results obtained are summarized as follows ; (1) The maximum erosion rate by cavitation erosion in both of fresh-water and sea-water appeared to be proportioned to their hardness and tensile strength. (2) Cavitation weight loss and rate of cast iron in sea-water condition were greater (approximately 3 times) than that in distilled-water condition, however in case of stainless and brass the cavitation weight loss and their rates were not so different in both of their conditions. (3) Cavitation weight loss of composite materials were shown as below on this test, DuraTough DL : Weight loss in sea-water condition were greater (approximately 2.3 times) than it's fresh-water condition. (4) As the result of observation with digital camea of specimens, the main tendency of cavitation erosion for metals, was that small damaged holes causing by cavitation e개sion was appeared with radial pattern, and composites materials was that small damaged holes were appeared randomly.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.383-390
• /
• 2008

Flow pattern of cavitation around a plano-convex foil, whose shape is similar to the inducer impeller of the turbo-pumps in the liquid fuel rocket engine, was observed by using a cryogenic cavitation tunnel of blowdown type for visualization. Working fluids were liquid nitrogen and hot water. The parameter range to be varied was between 20 and 60mm for channel width, 20 and 60mm for foil chord, -1.8 and 13.2 for cavitation number, 3.7 and 19.5m/sec for averaged inlet velocity, $8.5{\times}10^4$ and $1.5{\times}10^6$ for Reynolds number, -8 and $8^{\circ}$ for angle of attack, respectively. Especially at positive angle of attack, namely, convex surface being downstream, the whole cavity or a part of the cavity on the foil surface departs periodically. Periodic cavitation occurs only in case of smaller cavitation size than twice foil chord. Cavitation thickness and length in 20mm wide channel are larger than those in 60mm due to the wall confinement effect. Therefore, periodic cavitation in 60mm wide channel easily occurs than that in 20mm. These results suggest that the periodic cavitation is controlled by not only the hydrodynamic effect of vortex shedding but also the channel wall confinement effect.

• The Journal of the Acoustical Society of Korea
• /
• v.40 no.1
• /
• pp.38-45
• /
• 2021

In this study, changes in cavitation pattern and noise by air injection were investigated experimentally in a cavitation tunnel. Air injection system that can control the location and the amount of air was manufactured and installed in an elliptic wing that exhibits similar characteristics to those of a propeller blade. Various types of cavitation were simulated on the hydrofoil by adjusting the test conditions in the cavitation tunnel, and the changes in cavitation pattern and noise according to air injection were experimentally analyzed. It was shown that the noise characteristics varied depending on the position and the amount of air injection. This means that in order to apply the air injection technology to the propeller, it is necessary to optimize the air injection location and the amount of injection according to the cavitation characteristics.

• International Journal of Fluid Machinery and Systems
• /
• v.3 no.2
• /
• pp.137-149
• /
• 2010

The purpose of the present research is to suppress cavitation instabilities by using a circumferential groove. The circumferential groove was designed based on CFD so that the tip leakage vortex is trapped by the groove and does not interact with the next blade. Experimental results show that the groove can suppress rotating cavitation, asymmetric cavitation and cavitation surge. However, weak instabilities with higher frequency could not be suppressed by the groove. From the analysis of pressure pattern similar to that for rotor-stator interaction, it was found that the higher frequency components are caused by the interaction of backflow vortices with the inducer blades.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.4
• /
• pp.61-70
• /
• 2007

Numerical analysis of three dimensional incompressible turbulent flows in LNG marine high pressure drop control valves was carried out by using the CFD-ACE from ESI-Group. In this study, flow characteristics of control valves with complex flow fields including cavitation effect were investigated. Simulation was performed on five models of control valve that had different orifice diameters of anti-trim and the size of valve. Comparing newly designed control valves for controling the occurrence of cavitation with the conventional valve, new valves showed a improved flow pattern with almost no cavitation.