• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1256-1257
• /
• 2008

Dye-Sensitized Solar Cell(DSSC) is a new type of solar cell by using photocatalytic properties of $TiO_2$. The size and shape of $TiO_2$ particle are two of important parameters that are related to the characteristics of DSSC. And these can be changed by controlling $TiO_2$ sintering conditions especially temperature. The particles of $TiO_2$ are classified anatase and rutile. Anatase particles are created at low sintering temperature and rutile particles are created at high sintering temperature. Anatase particles have advantages such as increased surfaces that cause more attached dye molecules, and fast electron transportation. And rutile particles have advatages such as more efficient light scattering. Therefore, we studied characteristics of DSSC in this paper as $TiO_2$ sintering temperature is varied. As a result, we found that characteristics of DSSC are very good in the case that anatase and rutile particles are together and this sintering temperature is 450$^{\circ}C$.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.387-390
• /
• 2008

This study investigated the influence of electric facilities damaged by dusts and domestic regulations. Its contents included the around circumstance of electric facilities, regulations concerned with the dust, the actual conditions at the scene, the characteristics of dusts and so on. At the set-up the electric facilities, the around circumstances are bad in summer that highly temperature and many moisture. Besides, elements that are judged the corrosive vapours of the large quantity are detected at the sampled dusts. As the results, if dusts covered with electric facilities, It will be a cause for the electric accidents. From the analyzed data of the actual conditions and the sampled dusts, electric facilities maintenance for the viewpoint of the safety can be possible.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.4
• /
• pp.76-82
• /
• 2017

The cylinder liner of a diesel engine is commonly made of gray cast iron. However, this cylinder liner can be damaged by the cavitation phenomenon in wet conditions. This cavitation has remained an unsolved problem until now. In this study, the cause of cavitation corrosion due to antifreeze solution was examined using a scanning electron microscope (SEM) and a 3D microscope. The necessary data to prevent the damage caused by cavitation erosion and the corrosion of gray cast iron cylinder liner was obtained. Analysis determined that the gray iron structure consists of an ${\alpha}-matrix$, flake graphite, and steadite. Cavitation erosion was initiated in the coarse flake graphite and propagated into the steadite with pitting. Under repetitive reaction conditions, the ${\alpha}-matrix$ was partially separated from the gray cast iron. This study is expected to be used as the basic data for the prevention of gray cast iron cavitation erosion and corrosion by controlling the graphite and steadite phases.

• Textile Coloration and Finishing
• /
• v.27 no.3
• /
• pp.219-227
• /
• 2015

This study aims to propose a method to reduce hair damage after investigating the following: the factors which vary depending on hair treatment conditions; the degree of hair damage in the bleached sample; and an analysis of the effects of a perm on wave formation. To determine the effects of these treatment types, hair bleach was mixed with the hair treatment, and hair damage and formation of permanent waves were examined. Using a scanning electron microscope, in addition, morphological changes were analyzed and the following results were obtained: After mixing natural powder(2.5g) and hair cream(2.5g) and bleaching the mixture, it was compared to the scale structure of untreated hair. When 5g of natural powder was mixed and bleached, a clear layer was observed among cuticle scales, showing the effects of hair treatment. Therefore, this confirms that the effects of hair treatment were most notable when grain powder was mixed with hair cream. Once hair is damaged, it is almost impossible to regain its original state. When chemical agents are used, therefore, it is important to consider the possible hair damage they cause.

• Design & Manufacturing
• /
• v.13 no.4
• /
• pp.51-56
• /
• 2019

Due to industrial development, the importance of GD&T tolerance is growing day by day. Roundness measurement means the size deviated from the ideal circle. Roundness evaluation methods include LSCI, MZCI, MCCI, and MICI. Generally, A is used a lot at industrial evaluation. In this experiment, we studied the variations in table velocity, filter values, and detector angles, which can cause errors in roundness measurements. The measurement conditions were table speeds of 10, 30 and 60 mm/s, probe angles of 10, 20 and 30 degrees and frequency filter settings of 15, 150 and 500 upr and The number of experiments was measured 30 and the average value was chosen as a representative value. The hypothesis test showed that the p-value for the frequency filter was greater than 0.05, and the experiment rejected the null hypothesis and adopted the alternative hypothesis.

• 한국연소학회:학술대회논문집
• /
• 2002.11a
• /
• pp.209-214
• /
• 2002

Computations were performed to investigate the flow, temperature and pollutants in two stage heavy-oil combustion burner. The burner geometry and flow conditions were provided by a burner company. The goal of the study is to understand combustion phenomena according to each air inlet's velocity, excessive air ratio and air temperature through CFD. Air flow rates at two inlets are adjusted by a damper inside a burner. Here, injection conditions of liquid fuel are kept constant throughout all simulations. This assumption is made in order to limit the complexity of oil combustion though it may cause some disagreement. The final goal of this research is to design a Low-NOx heavy oil combustion burner through comparison between computational study and experimental ones. Besides experiments, simulation works can give us insights into heavy oil combustion and help us design a Low NOx burner while saving time and cost. The computational study is based on k-e model, P-1 radiation model(WSGGM) and PDF, and is implemented on a commercial code, FLUENT.

• Biomolecules & Therapeutics
• /
• v.12 no.3
• /
• pp.179-184
• /
• 2004

The FimH subunit of type 1-fimbriated Escherichia coli has been determined as a major cause for urinary tract infections. In our previous study, the Adhesin/CTXA2B was expressed as soluble recombinant chimaeric protein derived from the uropathogenic Escherichia coli adhesin genetically coupled to cholera toxin A2B (CTXA2B) subunit in Escherichia coli. Since it is very important to optimize IPTG concentration and culture temperature to maximize cell growth and productivity, These optimal culture factors were determined to increase the productivity of the expressed Adhesin/CTXA2B chimaeric protein in Escherichia coli TB1 carrying pMALfimH/ctxa2b. Our data demonstrate that optimal concentration of IPTG for increased production of chimaeric protein was 0.5 mM. Additionally, culture time was 10 hours and temperature, 37${\circ}C$.

• International Journal of Precision Engineering and Manufacturing
• /
• v.5 no.4
• /
• pp.5-13
• /
• 2004

This study explains the effects of lubricant and surface treatment on the life of hot forging dies. The thermal load and thermal softening, that occur when there is contact between the hotter billet and the cooler dies in hot forging, cause wear, thermal cracking and fatigue, and plastic deformation. Because the cooling effect and low friction are essential to the long life of dies, the proper selection of lubricant and surface treatment is very important in hot forging process. The two main factors that decide friction and heat transfer conditions are lubricant and surface treatment, which are directly related to friction factor and surface heat transfer coefficient. Experiments were performed for obtaining the friction factors and the surface heat transfer coefficients in different lubricants and surface treatments. For lubrication, oil-base and water-base graphite lubricants were used, and ion-nitride and carbon-nitride were used as surface treatment conditions. The methods for estimating die service life that are suggested in this study were applied to a finisher die during the hot forging of an automobile part. The new techniques developed in this study for estimating die service life can be used to develop more feasible ways to improve die service life in the hot forging process.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.1
• /
• pp.374-395
• /
• 2017

Users quite often experience volatile channel conditions which negatively influence multimedia transmission. HTTP adaptive streaming has emerged as a new promising technology where the video quality can be adjusted to variable network conditions. Nevertheless, the new technology does not remain without drawbacks. As it has been observed, multiple video players sharing the same network link have often problems with achieving good efficiency and stability of play-out due to a mutual interference and competition among video players. Our investigation indicates that there may be another cause for under-performance of the streamed video. In an emulated environment, we implemented three algorithms of adaptive video play-out based on bandwidth or buffer assessment. As we show, traffic generated by players employing the same or similar play-out strategies is positively correlated and synchronised (clustered), whereas traffic originated from different play-out strategies shows negative or no correlations. However, when some of the parameters of the play-out strategies are randomised, the correlation and synchronisation diminish what has a positive impact on the smoothness of the traffic and on the video quality perceived by end users. Our research shows that non-correlated traffic flows generated by play-out strategies improve efficiency and stability of streamed adaptive video.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.6
• /
• pp.632-638
• /
• 2015

Many failures have been reported in gas turbine facilities owing to repeated startups and prolonged use of the turbines. In this study, the causes and mechanism of fatigue failure in the first blade of a gas turbine were analyzed using a finite element method to calculate the centrifugal force, bending force, and a modal analysis based on the stress-stiffening effect and harmonic response under the operating conditions. The results show that, fatigue damage was caused by the resonance conditions encountered, in which the first natural frequency declined along with an increase in the metal temperature of the blade. The position of the expected fatigue damage was shown to match the actual position of the cracking at the root area of the blade, which was on the concave side. In addition, the equivalence fatigue stress was observed to approach the fatigue limit.