• 대한방사선기술학회지:방사선기술과학
• /
• 제44권4호
• /
• pp.301-306
• /
• 2021

The skull has peripheral organs such as the crystalline lens and thyroid gland, which are highly radiosensitive, but the examination is performed without considering the uneven dose distribution due to the heel effect at the time of the current Skull Town's examination. However, no studies have been conducted on the exposure dose of surrounding organ tissues due to the difference in image density due to the heel effect and the non-uniformity of the dose. Using the cathode (-) and anode (+) set on the Tube to measure the scattered radiation along the Tube direction as a guide, change 30° and 37° in the cathode direction and 30° and 37° in the anode direction. It was given and investigated 5 times to obtain scattered radiation. image measurements were SNR, PSNR, RMSE, and MAE. Measurement results Measurement results of surrounding organ doses when the Tube direction was 30° and 37° The dose was low when the direction was cathodic in all organs (p<0.000). Both cathodes were higher in the image measurements(p<0.04). Continuous research may be needed for diagnostically valuable imaging and minimization of patient exposure dose.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.306-309
• /
• 2005

One of the most critical issues in sol id oxide fuel cell (SOFC)running on hydrocarbon fuels is the risk of carbon formation from the fuel gas. The simple method to reduce the risk of carbon formation from the reactions is to add steam to the fuel stream, leading to the carbon gasification react ion. However, the addition of steam to fuel is not appropriate for the auxiliary power unit (APU) and potable power generation (PPG) systems due to an increase of complexity and bulkiness. In this regard, many researchers have focused on so-called 'direct methane' operation of SOFC, which works with dry methane without coking. However, coking can be suppressed only by the operation with a high current density, which may be a drawback especially for the APU and PPG systems. The single chamber fuel cell (SC-SOFC) is a novel simplification of the conventional SOFC into which a premixed fuel/air mixture is introduced. It relies on the selectivity of the anode and cathode catalysts to generate a chemical potential gradient across the cell. Moreover it allows compact and seal-free stack design. In this study, we fabricated honeycomb type mixed-gas fuel cell (MGFC) which has advantages of stacking to the axial direction and increasing volume power density. Honeycomb-structured SOFC with four channels was prepared by dry pressing method. Two alternative channels were coated with electrolyte and cathode slurry in order to make cathodic reaction sites. We will discuss that the anode supported honeycomb type cell running on mixed gas condition.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 1999년도 추계학술발표회 초록집
• /
• pp.15-15
• /
• 1999

In chip plating, several parameters must be taken into consideration. Current density, solution concentration, pH, solution temperature, components volume, chip and media ratio, barrel geometrical shape were most likely found to have an effect to the process yields. The 3 types of barrels utilized in chip plating industry are the conventional rotating barrel. vibrational barrel (vibarrel), and the centrifugal type. Conventional rotating barrel is a close type and is commonly used. The components inside the barrel are circulated by the barrel's rotation at a horizontal axis. Process yield has known to have higher thickness deviation. The vibrational barrel is an open type which offers a wide exposure to electrolyte resulting to a stable thickness deviation. It rotates in a vertical axis coupled with multi-vibration action to facilitate mixed up and easy transportation of components, The centrifugal barrel has its plated work centrifugally compacted against the cathode ring for superior electrical contact with simultaneous rotary motion. This experiment has determined the effect of barrel vibration intensity to the plating thickness distribution. The procedures carried out in the experiment involved the overall plating process., cleaning, rinse, Nickel plating, Tin-Lead plating. Plating time was adjusted to meet the required specification. All other parameters were maintained constant. Two trials were performed to confirm the consistency of the result. The thickness data of the experiment conducted showed that the average mean value obtained from higher vibrational intensity is nearer to the standard mean. The distribution curve shown has a narrower specification limits and it has a reduced variation around the target value, Generally, intensity control in vi-barrel facilitates mixed up and easy transportation of components, However, it is desirable to maintain an optimum vibration intensity to prevent solution intrusion into the chips' internal electrode. A cathodic reaction can occur in the interface of the external and internal electrode. $2HD{\;}+{\;}e{\;}{\rightarrow}20H{\;}+{\;}H_2$ Hydrogen can penetrate into the body and create pressure which can cause cracks. At high intensity, the chip's motion becomes stronger, its contact between each other is delayed and so plating action is being controlled. However, the strong impact created by its collision can damage the external electrode's structure thereby resulting to bad plating condition. 1 lot of chip was divided into two equal partion. Each portion was loaded to the same barrel one after the other. Nickel plating and tin-lead plating was performed in the same station. Portion A maintained the normal barrel vibration intensity and portion B vibration intensity was increased two steps higher. All other parameters, current, solution condition were maintained constant. Generally, plating method find procedures were carried out in a best way to maintained the best plating condition. After plating, samples were taken out from each portion. molded and polished. Plating thickness was investigated for both. To check consistency of results. 2nd trial was done now using different lot of another characteristics.

• Restorative Dentistry and Endodontics
• /
• 제13권2호
• /
• pp.221-235
• /
• 1988

The purpose of this study was to observe characteristic properties through the polarization curves and EMPA images from 4 different types of amalgam obtained by using the potentiostats (EG & G PARC) & EPMA (Jeol JSM-35), to investigate the degree of corrosion of each phase of amalgam on the oxidation peak, and to identify corrosion products from the corroded amalgam by use of X-ray diffractometer(Rigaku). After each amlgam alloy and Hg were triturated as the direction of the manufacturer by means of the mechanical amalgamator(Shofu), the triturated mass was inserted into the cylindrical metal mold which was 12mm in diameter and 10mm in height and was condensed by means of routine manner. The specimen was removed from the mold and stored at room temperature for about 7 days. The standard surface preparation was routinely carried out. Anodic polarization measurement was employed to compare the corrosion behaviours of the amalgams in 0.9% saline solution(pH6.8~7.0) and artificial saliva (pH6.8~7.0) at $37^{\circ}C$. The open circuit potential was determined after 30 minutes' immersion of specimen in electrolyte and the potential scan was begun at the potential of 100mV cathodic from the corrosion potential. The scan rate was 1mV/sec and the surface area of amalgam exposed to the solution was 0.64$cm^2$ for each specimen. All the potentials reported are with respect to a saturated calomel electrode (SCE). EPMA images on the determined oxidation peaks of each amalgam in artificial saliva were observed. X-ray diffraction patterns of each sample were recorded before and after polarization in artificial saliva (Aristaloy, Caulk Spherical, Dispersalloy and Tytin: at +770mV, +585mV, +8.10m V and +680m V respectively) by use of a recording diffractometer. Nickel filtered Cu $K_{{\alpha}_1}$ radiation was used and sample was scanned at $4^{\circ}(2{\theta})/min.$ from $25^{\circ}$ to $80^{\circ}$. The following results were obtained. 1. Oxidation peak potential in artificial saliva shifted to more anodic direction than that in saline solution. 2. The corrosion potential of high copper amalgam was more anodic than the potential of low copper amalgam. 3. The current density was lower in artificial saliva than in saline solution. 4. One of the corrosion products, AgCl was identified by X-ray diffraction analysis. 5. ${\gamma}_2$ phase was the most susceptible to corrosion and e phase was stable in low copper amalgam and ${\eta}$' phase and Ag-Cu eutectic were susceptible to corrosion in high copper amalgam.

• Corrosion Science and Technology
• /
• 제13권1호
• /
• pp.28-35
• /
• 2014

Recently, the fuel oil of diesel engines of marine ships has been increasingly changed to heavy oil of low quality as the oil price is getting higher and higher. Therefore, the spiral gear attached at the motor of the oil purifier which plays an important role to purify the heavy oil is also easy to expose at severe environmental condition due to the purification of the heavy oil in higher temperature. Thus, the material of the spiral gear requires a better mechanical strength, wear and corrosion resistance. In this study, the heat treatment(tempering) with various holding time at temperature of $500^{\circ}C$ was carried out to the alloy of Cu-7Al-2.5Si as centrifugal casting, and the properties of both hardness and corrosion resistance with and without heat treatment were investigated with observation of the microstructure and with electrochemical methods, such as measurement of corrosion potential, cathodic and anodic polarization curves, cyclic voltammogram, and a.c. impedance. in natural seawater solution. The ${\alpha}$, ${\beta}^{\prime}$ and ${\gamma}_2$ phases were observed in the material in spite of no heat treatment due to quenching effect of a spin mold. However, their phases, that is, ${\beta}^{\prime}$ and ${\gamma}_2$ phases decreased gradually with increasing the holding time at a constant temperature of $500^{\circ}C$. The hardness more or less decreased with heat treatment, however its corrosion resistance was improved with the heat treatment. Furthermore, the longer holding time, the better corrosion resistance. In addition, when the holding time was 48hrs, its corrosion current density showed the lowest value. The pattern of corroded surface was nearly similar to that of the pitting corrosion, and this morphology was greatly observed in the case of no heat treatment. It is considered that ${\gamma}_2$ phase at the grain boundary was corroded preferentially as an anode. However, the pattern of general corrosion exhibited increasingly due to decreasing the ${\gamma}_2$ phase with heat treatment. Consequently, it is suggested that the corrosion resistance of Cu-7Al-2.5Si alloy can be improved with the heat treatment as a holding time for 48 hrs at $500^{\circ}C$.

• Nuclear Engineering and Technology
• /
• 제27권4호
• /
• pp.453-462
• /
• 1995

사용후 핵연료 저장구조재의 구조적 안정성자 관련해서, 감마선 조사 생성물로 알려져 있는 $H_2O$$_2$를 전해질에 주입시키었을 때, $H_2O$$_2$가 저장구조재인 304L스텐리스강의 부식거동에 어떤 영향을 미치는가를 조사하였다. 실험결과, $H_2O$$_2$는 304L 스텐리스강의 부식전위를 상승시키고 Pitting 전위를 감소시킴으로써 부동태 영역을 줄이고 pitting 저항성을 감소시키는 것으로 나타났다. 이는 감마선 조사에 의한 부식 거동 변화와 유사한 결과라고 볼 수 있으며, 또한 산소농도증가에 의한 부식거동 변화와 유사한 결과로 해석되었다. 재부동태형성전위가 $H_2O$$_2$의 존재로 증가하는데, 이로써 응력부식균열임계전위는 약간 상승할 것으로 추론되었다. 그러나, $H_2O$$_2$ 농도가 6.3$\times$$10^{-6}$M 이하로 떨어질 경우, $H_2O$$_2$는 부식거동에 영향을 주지 못했다. 이는 대기압상태에서 용존된 $O_2$환원반응속도에 비해 $H_2O$$_2$환원반응속도가 작기 때문이라고 해석되었다. 중성용액보다 산성 및 염기성 용액에서, $H_2O$$_2$가 부식거동에 미치는 영향이 작아졌는데, 이는 산성용액에서는 높은 H$^{+}$ 농도 때문에, 염기성용액에서는 le Chatelier의 원칙 때문인 것으로 해석되었다.

• Korean Chemical Engineering Research
• /
• 제60권4호
• /
• pp.588-593
• /
• 2022

본 논문에서는 hemin, 폴리에틸렌이민(PEI) 및 탄소나노튜브(CNT)를 이용하여 제조 CNT/PEI/hemin/PEI 복합재에 가교제인 테레프탈알데하이드(TPA)를 첨가하여 전자전달이 개선된 과산화수소 환원 반응(HPRR) 촉매를 합성하였다. 합성된 촉매(CNT/PEI/hemin/PEI/TPA)를 과산화수소 10 mM 농도에서 HPRR 반응성을 확인한 결과, 0.2 V (vs. Ag/AgCl)에서 0.2813 mA cm^-2의 전류 밀도로 나타났으며, 이는 가교하지 않은 촉매(CNT/PEI/hemin/PEI)와 범용 가교제인 글루타르알데하이드(GA)에 의해 가교된 촉매(CNT/PEI/hemin/PEI/GA)에 비해 각각 2.43 및 1.87배 증가하였다. CNT/PEI/hemin/PEI/TPA의 HPRR 개시전위는 0.544 V로서 CNT/PEI/hemin/PEI와 CNT/PEI/hemin/PEI/GA의 0.511 및 0.471 V에 비하여 원활한 전자전달에 의해 개선되었음을 확인할 수 있었다. 이는 전기화학 임피던스 분광법(EIS)을 이용한 분석 결과에서도 확인되었는데, CNT/PEI/hemin/PEI/GA의 경우, 전자전달을 방해하는 가교제의 도입에 따라 CNT/PEI/hemin/PEI에 비하여 높은 전자전달저항을 나타낸 반면, CNT/PEI/hemin/PEI/TPA는 6.2% 감소하여, 가장 낮은 전자전달저항을 나타냈다. 막이 없는 흐름형 과산화수소 연료전지를 이용한 평가에서도, CNT/PEI/hemin/PEI/TPA를 환원극으로 활용한 전지의 최대 출력 밀도가 36.34±1.41 μWcm^-2로, CNT/PEI/hemin/PEI (27.87±0.95 μWcm^-2)와 CNT/PEI/hemin/PEI/GA(25.57±1.32 μWcm^-2) 보다 높게 측정되어, TPA는 전자전달을 개선 성능을 확인할 수 있었다.