• 한국물환경학회지
• /
• 제26권4호
• /
• pp.681-686
• /
• 2010

Two different MFC designs were evaluated in batch mode: single compartment combined membrane-electrodes (SCME) design and twin-compartment brush-type anode electrodes (TBE) design (single chamber with two air cathodes and brush anodes at each side of the reactor). In SCME MFC, carbon anode and cathode electrodes were assembled with a proton exchange membrane (PEM). TBE MFC was consisted of brush-type anode and carbon cloth cathode electrodes without the PEM. A brush-type anode was fabricated with carbon fibers and was placed close to the cathode electrode to reduce the internal resistance. Substrates used in this study were glucose, leachate from cattle manure, or sucrose at different concentrations with phosphate buffer solution (PBS) of 200 mM to increase the conductivity thereby reduce the internal resistance. Hydrogen generating bacteria (HGB) were only inoculated in TBE MFC. The peak power densities ($P_{peak}$) produced from the SCME systems fed with glucose and leachate were 18.8 and $28.7mW/m^2$ at external loads of 1000 ohms, respectively. And the $P_{peak}$ produced from TBE MFC were 40.1 and $18.3mW/m^2$ at sucrose concentration of 5 g/L and external loads of 470 ohms, with a mediator (2-hydroxy-1, 4-naphthoquinone) and without the mediator, respectively. The maximum power density ($P_{max}$) produced from mediator present TBE MFC was $115.3mW/m^2$ at 47 ohms of an external resistor.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.353-356
• /
• 2009

A pivotal mechanical balance of plant for 75kW class molten carbonate fuel cells comprise of a catalytic burner and an ejector which has been designed and tested in KEPRI(Korea Electric Power Research Institute). The catalytic burner, which oxidizes residual fuel in the anode tail gas, was operated at several conditions. Some problems arose due to local overheating or auto-ignition, which could limit the catalyst life. The catalytic burner was designed by considering both gas mixing and gas velocity. Test results showed that the temperature distribution is very uniform. In addition, an ejector is a fluid machinery to be utilized for mixing fluids, maintaining vacuum, and transporting them. The ejector is placed at mixing point between the anode off gas and the cathode off gas or the fresh air Several ejectors were designed and tested to form a suction on the fuel tail gas and balance the differential pressures between anode and cathode over a range of operating conditions. The tests showed that the design of the nozzle and throat played an important role in balancing the anode tail and cathode inlet gas pressures. The 75kW MCFC system built in our ejector and catalytic burner was successfully operated from Novembe, 2008 to April, 2009. It recorded the voltage of 104V at the current of 754A and reached the maximum generating power of 78.5kW DC. The results for both stand-alone and integration into another balance of plant are discussed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.1038-1041
• /
• 2003

In the paper, we investigated silicon surface microstructures formed by reactive ion etching in hollow cathode system. Wet anisotropic chemical etching technique use to form random pyramidal structure on <100> silicon wafers usually is not effective in texturing of low-cost multicrystalline silicon wafers because of random orientation nature, but High density hollow cathode plasma system illustrates high deposition rate, better film crystal structure, improved etching characteristics. The etched silicon surface is covered by columnar microstructures with diameters form 50 to 100nm and depth of about 500nm. We used $SF_{6}$ and $O_{2}$ gases in HCP dry etch process. This paper demonstrates very high plasma density of $2{\times}10^{12}$ $cm^{-3}$ at a discharge current of 20 mA. Silicon etch rate of 1.3 ${\mu}s/min$. was achieved with $SF_{6}/O_{2}$ plasma conditions of total gas pressure=50 mTorr, gas flow rate=40 sccm, and rf power=200 W. Our experimental results can be used in various display systems such as thin film growth and etching for TFT-LCDs, emitter tip formations for FEDs, and bright plasma discharge for PDP applications. In this paper we directed our study to the silicon etching properties such as high etching rate, large area uniformity, low power with the high density plasma.

• 한국수소및신에너지학회논문집
• /
• 제26권5호
• /
• pp.416-422
• /
• 2015

Lithium Ion capacitor (LIC) is a new storage device which combines high power density and high energy density compared to conventional supercapacitors. LIC is capable of storing approximately 5.10 times more energy than conventional EDLCs and also have the benefits of high power and long cycle-life. In this study, LICs are assembled with activated carbon (AC) cathode and pre-doped graphite anode. Cathode material of natural graphite and artificial graphite kinds of MAGE-E3 was selected as the experiment proceeds. Super-P as a conductive agent and PTFE was used as binder, with the graphite: conductive agent: binder of 85: 10: 5 ratio of the negative electrode was prepared. Lithium doping condition of current density of $2mA/cm^2$ to $1mA/cm^2$, and was conducted by varying the doping. Results Analysis of Inductively Coupled Plasma Spectrometer (ICP) was used and a $1mA/cm^2$ current density, $2mA/cm^2$, when more than 1.5% of lithium ions was confirmed that contained. In addition, lithium ion doping to 0.005 V at 10, 20 and $30^{\circ}C$ temperature varying the voltage variation was confirmed, $20^{\circ}C$ cell from the low internal resistance of $4.9{\Omega}$ was confirmed.

• 한국진공학회지
• /
• 제9권3호
• /
• pp.290-295
• /
• 2000

KAIST-TOKAMAK에서 재현성이 좋은 저항가열 플라즈마를 발생시키는데 필요한 전이온화(pre-ionization)에 응용하기 위해 2.45 GHz 마그네트론을 사용하여 간편한 마이크로파 발생장치를 개발하였다. 장치에 사용한 마그네트론은 출력 500 W, 주파수 2.45 GHz이며, 일반적인 가정용 전자오븐(microwave oven)에 사용된다. 기존의 가정용 마그네트론은 음극(cathode)과 양극(anode)사이에 걸리는 고전압이 60 Hz의 주기를 갖기 때문에 약 16ms마다 약 8 ms 동안만 주기적으로 마이크로파를 발생한다. 이 마그네트론을 사용하여 토카막 전이온화에 충분할 정도로 연속적으로 발생되는 마이크로파를 얻기 위해서 음극과 양극사이에 개량된 회로로 리플전압이 작은 DC 고전압(5 kV 1 A)을 인가하였다. 본 논문에서는 주기적으로 생성.소멸하는 ECH 플라즈마와 연속적인 ECH 플라즈마를 발생시켜 랑뮈어탐침과 광증배관(PMT)을 이용한 이온 포화전류와 $H_\alpha$/ 방출(emission)을 측정하여 마이크로파 발생장치의 특성을 조사하였다.

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 2003년도 추계총회 및 학술발표회
• /
• pp.23-23
• /
• 2003

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2006년도 전력전자학술대회 논문집
• /
• pp.239-241
• /
• 2006

본 논문에서는 Liquid crystal display (LCD) Backlight module중에 Cold cathode fluorescent lamp (CCFL)를 포함한 인버터가 가지고 있는 기생 용량 측정 방법을 고안하였다. CCFL의 부성 저항 특성을 고려하여 램프의 정적 저항 성분을 일정하게 유지시키고 입력 전압 대 출력 전압의 비 중 최대 Gain을 갖는 주파수를 찾아내 기생 용량을 계산하는 Algorithm을 완성하였다. 시뮬레이션과 실험 결과를 통해 비교 검증함으로써 측정 방법의 유효성을 입증하였다.

• 한국태양에너지학회 논문집
• /
• 제34권4호
• /
• pp.17-22
• /
• 2014

The design of a fuel cells stack is important to get optimal output power. This study focuses on the evaluation of fuel cell system for unmaned aerial vehicles (UAVs). Low temperature proton exchange membrane (LTPEM) fuel cells are the most promising energy source for the robot applications because of their unique advantages such as high energy density, cold startup, and quick response during operation. In this paper, a 600 W open cathode LTPEM fuel cell was tested to evaluate the performance and to determine optimal operating conditions. The open cathode design reduces the overall size of the system to meet the requirement for robotic application. The cruise power requirement of 600 W was supported entirely by the fuel cell while the additional power requirements during takeoff was extended using a battery. A peak of power of 900 W is possible for 10 mins with a lithium polymer (LiPo) battery. The system was evaluated under various load cycles as well as start-stop cycles. The system response from no load to full load meets the robot platform requirement. The total weigh of the stack was 2 kg, while the overall system, including the fuel processing system and battery, was 4 kg.

• 전기화학회지
• /
• 제3권3호
• /
• pp.152-156
• /
• 2000

그물구조 다공성 금속을 황산과 황산구리 수용액을 전해질로 사용하여 전기화학적으로 제조하였으며, 이때 균질 전착에 영향을 미치는 구리이온 농도에 대해 살펴보았다. 전해질 중의 황산에 대한 구리이온의 농도비가 감소하면 전해질의 점성이 감소하여 전기전도도의 향상을 가지고 오며, 분극도(polarizability)의 상승을 유발시켜 균일 전류밀도 분포력(throwing power)을 향상시키는 효과를 나타내었다. 그물구조 다공성 금속을 제조하기 위한 최적의 조건은 한계 전류밀도와 균일 전류밀도 분포력을 고려하여 결정되어야 하며, 인가전류가 $10mA/cm^2$일 때 0.2M $CuSO_4\cdot\;5H_2O+0.5\;H_2SO_4$임을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.1322-1324
• /
• 2002

For developing a 100 kW MCFC power generation system, Several design parameters for a fuel cell stack and system analysis results by Cycle Tempo, a processing computer soft ware, were described. Approximately 170 cells are required to generate 100 kW at a current density of 125 mA/$cm^2$ with 6000 $cm^2$ cells. An overall heat balance was calculated to predict exit temperature. The 100 kW power is expected only under pressurized operation condition at 3 atm. Recycle of cathode gas by more than 50% is recommended to run the stack at 125 mA/$cm^2$ and 3 atm. Manifolds should be designed based on gas flow rates for the suggested operating condition. The fuel cell power generation system was designed conceptually with several choices of utilization of anode exhaust gas. Also system efficiency was calculated at various type of system and operation conditions.