• Korean Journal of Materials Research
• /
• v.16 no.11
• /
• pp.668-675
• /
• 2006

In the partial squeeze casting process, the filling behavior of liquid metal and solidification pattern in thick area have significant influence on the quality of casting products and die life. For the optimal casting design of automobile transmission gear housing, various analyses were performed in this study by using computer simulation code, MAGMAsoft and the simulation results were compared and analyzed with experimental results. By air pressure criteria, internal porosities caused by air entrap during the mold filling were predicted and reduced remarkably by modification of gating system. Also, optimal squeeze-time lag to apply partial squeeze pin in thick area was calculated and the castings was free from shrinkage defects with the result of solidification analysis. Consequently, casting design for automobile transmission gear housing was optimized and approved by Computer Tomography.

• Journal of Environmental Science International
• /
• v.24 no.5
• /
• pp.699-708
• /
• 2015

This study was performed to identify the state of the exposure and characteristics of pollutants by each process at 4 casting sites located in Gyeongsang-do from April to November 2013. The concentrations of methanol, crystallized silica glass, formaldehyde and phenol were analyzed by different process - casting process, molding process, core process, and shakeout & finishing process. The highest concentration of methanol was found in casting and molding process, whereas the highest concentration of crystalline quartz(Silica) was observed in core process. The most oxidized steel dusts and the highest concentration of fume were found in shakeout & finishing process. As a result of this study, those labors working at the casting site were found to be constantly exposed to various forms of hazardous chemicals; therefore, it is considered that this is the time to manage and plan how to reduce them. In addition, it is required to thoroughly manage the local exhauster, and improve the process and working environment to reduce various forms of hazardous chemicals.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.1
• /
• pp.25-32
• /
• 2022

Investment casting is a production method commonly used to manufacture precision equipment, medical fields, and accessories, and has continued to develop through the modernization of equipment and high quality of materials, and its scope of use has been expanded. The purpose of this study is to minimize the defect rate by deriving structural improvement and standardization of mold temperature, which are key elements of the investment casting process, to minimize the defect rate. The scope of the study is limited to jewelry manufacturing casting processes suitable for understanding the structure and principles of small gate, and an experimental research is to be conducted by using soft Wax, gypsum powder, and 14 K gold as research materials. According to the results, the most appropriate casting standard temperature for the casting pattern of Alloy 14 k was the lowest turbulence at 980℃ flask temperature of 550℃, so good products could be produced. As a future task of this study, detailed studies are needed to data the structure and system temperature of small gate, reduce production defects in the field, and provide data for excellent investment casting competitiveness.

• Transactions of Materials Processing
• /
• v.14 no.4 s.76
• /
• pp.351-359
• /
• 2005

The semi-solid processing is now becoming of great interest for the production of various parts by pressure die casting. Also, the rheo-casting has been substituted for thixo-casting, because the rheo-casting can control the solid particles to globular and non-dendritic solid phase. In the rheo-casting process, the important thing is to control the solid particles behavior in semi-solid materials. So in this paper, to control solid particles behavior in semi-solid materials, we experimented about the die filling tests during the semi-solid die casting in 0.3, 0.4, 0.5 and 0, 6 solid fraction. The die filling in semi-solid die casting were simulated by MAGMA soft/thixo module. By the die filling tests and computer simulation, the effect of solid particles behavior in rheology flow had been investigated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.664-667
• /
• 2004

The semi-solid processing is now becoming of great interest for the production of various parts by pressure die casting. Also, the rheolory casting has been substituted for thixo casting, because the rheology casting can control the solid particles to globular and non-dendritic solid phase. In the rheology casting process, the important thing is to control the solid particles behavior in semi-solid materials. So in this paper, to control solid particles behavior in semi-solid materials, we experimented about the die filling during the semi-solid die casting in 0.3, 0.4, 0.5, 0,6 solid fraction. The die filling in semi-solid die casting were simulated by MAGMAsoft/thixo module. By the die filling tests and computer simulation, the effect of solid particles behavior in rheology flow had been investigated.

• Journal of Korea Foundry Society
• /
• v.22 no.4
• /
• pp.155-159
• /
• 2002

Magnesium alloys have high strength to weight ratio and are extremely attractive for applications in transport industry. Most of structural magnesium alloys are manufactured by die casting process. The tensile properties of AZ91HP magnesium alloy were investigated after die casting under various die casting conditions. After die casting by using cold chamber machine, the volume porosity of specimens was examined with density method. With the increase of the volume porosity of specimens, both the tensile strength and elongation were significantly decreased, however the 0.2% offset strength was almost independent of the amount of porosity. With the increase of crystal pressure from 500 to 900 bar during die casting, the volume porosity was decreased, which resulted in the increase of the tensile strength. The mould temperature within the range of $150{\sim}250^{\circ}C$ has not influenced the microstructure with the eutectic phase and tensile properties of specimens. The tensile strength was the highest at 90m/sec of gate speed.

• Journal of Korea Foundry Society
• /
• v.35 no.3
• /
• pp.62-66
• /
• 2015

Tape casting is an important forming operation used to prepare flat sheets in the various industries. In this study, Doctor Blade tape casting of In-based low melting point alloy was carried out. The purpose of this investigation was to determine the possibility of applying the Doctor Blade tape casting process to the manufacture of low melting point alloy sheets that can be used as thermal fusible parts of battery safety systems. In-based molten alloy that has a melting point of $95^{\circ}C$ was produced; it's viscosity was measured at various temperatures. The molten alloy was used as a slip in the caster of the Doctor Blade tape casting system. The effects of the molten alloy temperatures and carrier speeds on the produced sheet shape were observed. For the casting conditions of 1.5 cm slip height, $120^{\circ}C$ slip temperature, 0.05 mm blade gap and 60 m/min. carrier speed, an In-based alloy thin tape well shaped with 0.16 mm uniform thickness was continuously produced.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.5
• /
• pp.945-952
• /
• 2023

In this study, the sand casting process was applied to design the gating system and perform casting simulation in order to domestically produce the submarine mast cover. Based on simulation results, casting experiments were conducted to produce a soundness prototype. The design concept of the mast cover's gating system was based on the design of bell casting. By arranging eight tower-type gates in a circle at 45° intervals, the flow of melt flowing into each gate was uniform and did not mix with each other, and the velocity of melt was also uniform. The mast cover made of Ni-Al-Bronze alloy has no unfilled parts. However, small porosities and flow marks occurred on the surface in several places. Yield strength and ultimate tensile strength are 279.3 MPa and 675.7 MPa, respectively, and elongation is 21.2%.

• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.446-449
• /
• 1999

본 연구에서는 기존의 자성 웨지의 제조공정을 대체하여 제조 공정이 단순하고, 그의 정밀성이 우수한 tape casting-lamination법에 의한 자성 웨지의 제조 공정의 적용 가능성에 대한 연구를 수행하였다. 철 분말과 에폭시 slurry는 우수한 tape casting 특성을 보여주었으며, 이렇게 얻어진 green tape과 유리 섬유를 적층하여 자성 웨지를 얻었다. 이러한 과정을 거쳐서 얻어진 제품의 품질 특성을 평가한 결과, 기존의 제조 공정으로 얻어진 제품에 비하여 품질의 균일성이 우수하며, 제조 공정을 혁신적으로 단축하는 것이 가능한 것을 보여주고 있다.

• Journal of the Korean Ceramic Society
• /
• v.52 no.6
• /
• pp.449-454
• /
• 2015

The fabrication process of zirconia gel-casting was studied to obtain dense zirconia on a large scale or with complicated shapes. As an experimental parameter, two different particle sizes ($0.1{\mu}m$ and $0.7{\mu}m$) of zirconia powder were applied to the gel-casting process. The viscosity behavior of slurries incorporating 40 vol% of zirconia powder was examined as a function of the dispersant content and the solid load to determine the optimum dispersion conditions. In addition, the gelation time with an initiator, the de-binding behavior, and the main factors affecting densification were examined. The densification of the gel-casted zirconia green body depended on the mixing ratio between the monomer and the dimer and on the zirconia particle size. A green body with a small particle size of $0.1{\mu}m$ showed less densification, with a relative density of 93%. This may be due to the excess number of bubbles created through interactions between the larger particle surface and polymer additives during the ball-milling process.