• 유체기계공업학회:학술대회논문집
• /
• 2001.11a
• /
• pp.419-424
• /
• 2001

TCV(Temperature control valve by pressure compensation) controls temperature constantly, when it is sending steam or high temperature water to heating device of heat exchanger. For designing TCV, the ratio of piston and hole diameters is one of the important design parameters. Numerical analysis is carried out to elucidate the flow characteristics in the TCV with different port areas of cold and hot waters, using the k-$\epsilon$ turbulence model and Cartesian cut-cell method. Numerical results show that the exit flow rate is mainly affected by pressure distribution in the piston.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.176.1-176
• /
• 2001

Conventional researches almost have been focused on the one dimensional inverted pendulum. Recently, Sprenger et al[2] have researched a two dimensional inverted pendulum Observing human's action to control an inverted pendulum, one can recognize that human uses a three dimensional metier including the up and down motion. In this paper, we propose a fuzzy logic controller(FLC) of a new three dimensional inverted pendulum system. We derive a dynamic equation of the mechanism including a 3-axis cartesian robot and a inverted pendulum. We propose a design method of a fuzzy controller of the yaw and pitch angles of a inverted pendulum. In the design, the redundant degree-of-freedom(DOF) of the robot ...

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.844-849
• /
• 1991

A high speed control system for a telerobot using DSP is developed. The system is designed to resolve computational burden in advanced algorithms. The design is assumed to h ave no specific algorithm and robot configuration. The system is composed of a teaching box, a DSP board, a set of servo drivers and 16 bit microcomputer system. The teaching box is designed as a man-machine interface, which has two joysticks with three degrees of freedom for velocity generation in Cartesian space. The DSP board, i.e. DSP56000ADS based on a 10.25MIPS digital signal processor, DSP56001, computes the inverse Jacobian matrix which transforms Cartesian velocity into joint velocity. A resolved motion rate control algorithm for a 5 degrees of freedom manipulator was implemented. About 100 Hz sampling rate was achieved in this system.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.125-130
• /
• 1991

This paper presents a tracking filter using pseudomeasurements in an estimated line-of-sight Cartesian coordinate system(ELCCS) whose x-axis is on the line-of-sight to an estimated target position. A target dynamics model and a measurement equation in the ELCCS are derived first and then a tracking filter in the ELCCS named moving coordinate tracking filter(MCTF) is proposed. It is shown that this MCTF is equivalent to a Kalman filter in the inertial Cartesian coordinate system which is widely used in the target tracking system. By approximating the MCTF for a pseudomeasurement noise and an error covariance matrix in the ELCCS, decoupling of three axes can be achieved. In this case, named decoupled moving coordinate tracking filter(DMCTF), computation time can be drastically reduced by utilizing its parallel structure. Finally, the stochastic properties of the MCTF and DMCTF are presented. Especially, a sufficient condition of nondestabilizing deviation for the DMCTF is proposed. The performance of the MCTF and DMCTF are compared with a conventional Kalman tracking filter.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.8 no.1
• /
• pp.67-80
• /
• 2004

In the present paper, a numerical algorithm for the kinematic analysis of a MacPherson strut motor-vehicle suspension system is developed. The kinematic analysis is carried out in terms of the rectangular Cartesian coordinates of some defined points in the links and at the joints. The presented formulation in terms of this system of coordinates is simple and involves only elementary mathematics. The resulting constraint equations are mostly either linear or quadratic in the rectangular Cartesian coordinates. The proposed formulation eliminates the need to write redundant constraints and allows to solve a reduced system of equations which leads to better accuracy and a reduction in computing time. The algorithm is applied to solve the initial positions as well as the finite displacement, velocity and acceleration problems for the MacPherson strut motor-vehicle suspension system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.369-373
• /
• 1992

Force control of a planar two-link structurally flexible robotic manipulator is considered in this study. The dynamic model is obtained by using the extended Hamilton's principle and the Galerkin criterion. A method is pressented toobtain the linearized equations of motion in Cartesian space for use in designing the control system. The approachto solving the control problem is to use feedforward and feedback control torques. The feedforward torques maneuver the flexible manipulatro along a nominal trajectory and the feedback torques minimize any deviations from the nominal trajectory. The linear quadratic Gaussian/loop transfer recovery (LQG/LTR) design methodology is explotied to design a robust feedback control system that can handle modeling errors and sensor noise, and operates on Cartesian space trajectory errors. The Lqg/LTR compenstaor together with a feedforward ollp is used to control the flexible manipulator. Simulated results are presented for a numerical example.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.2
• /
• pp.352-360
• /
• 1997

An inverse dynamic procedure for spatial multibody systems containing flexible bodies is developed in the relative joint coordinate space. Constraint acceleration equations are derived in terms of relative coordinates using the velocity transformation technique. An inverse velocity transformation operator, which transforms the Cartesian velocities to the relative velocities, is derived systematically corresponding to the types of kinematic joints connecting the bodies and the system reference matrix. Using the resulting matrix, the joint reaction forces and moments are analyzed in the Cartesian coordinate space. The formulation is illustrated by means of two numerical examples.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.7 s.178
• /
• pp.1826-1832
• /
• 2000

A modelling method for the bending vibration analysis of rotating cantilever beams employing finite element method is presented in this paper. Different from the conventional modelling method in wh ich only Cartesian deformation variables are used, a non-Cartesian deformation variable is introduced and approximated to derive the equations of motion. Numerical results obtained by using the presented modelling method are compared to those obtained by using other methods in the related literature, and the accuracy of the presented method is verified through the comparison study. The presented modelling method is superior to other previous methods in a sense that several advantages of the previous methods are incorporated into the presented method.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1724-1729
• /
• 2003

Two different subsystem synthesis methods with independent generalized coordinates have been developed and compared. In each formulation, the subsystem equations of motion are generated in terms of independent generalized coordinates. The first formulation is based on the relative Cartesian coordinates with respect to moving subsystem base (virtual) body. The second formulation is based on the relative joint coordinates using recursive formulation. Computational efficiency of the formulations has been compared theoretically by the operational counting method.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.2
• /
• pp.144-151
• /
• 1988

Between any two points in the Cartesian space, the straight motion has many distinct advantages in path/trajectory plannings, specially in a crowded workspace. But to achieve this motion is a nontrivial task. One standard way to approximate this motion is to plae enough intermediate points along the desired path and linearly interpolate two adjacent intermediate points in the joint space. In this approach, however, the determination of the minimum number of intermediate points is very important from several aspects. A scheme that can effectively accomplish this purpose is established in this paper. This scheme is based on several search methods. The results are demonstrated using the PUMA 560 series manipulator.