• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.192-197
• /
• 2004

The anisotropy in coefficient of thermal expansion (CTE) between the in-plane and out-of-plane of 3-dimensional thick composite structures induces residual stresses and the large void content due to insufficient compaction of fabric composites, which results in low interlaminar strengths. In order to reduce the through thickness CTE and the void content, in this work, carbon fabric phenolic laminates were compacted by pressure generated by autoclave and a compressive jig, from which the through-thickness CTEs and the void contents were measured. From the measurement, it was found that the through-thickness CTE and the void content had different characteristics from ordinary composites due to gas produced during the cure reaction of phenolic resin.

• Carbon letters
• /
• 제16권1호
• /
• pp.25-33
• /
• 2015

The prime objective of this research was to study the influence of hot-pressing pressure and matrix-to-reinforcement ratio on the densification of short-carbon-fiber-reinforced, randomly oriented carbon/carbon-composite. Secondary objectives included determination of the physical and mechanical properties of the resulting composite. The 'hybrid carbon-fiber-reinforced mesophase-pitch-derived carbon-matrix' composite was fabricated by hot pressing. During hot pressing, pressure was varied from 5 to 20 MPa, and reinforcement wt% from 30 to 70. Densification of all the compacts was carried at low impregnation pressure with phenolic resin. The effect of the impregnation cycles was determined using measurements of microstructure and density. The results showed that effective densification strongly depended on the hot-pressing pressure and reinforcement wt%. Furthermore, results showed that compacts processed at lower hot-pressing pressure, and at higher reinforcement wt%, gained density gradually during three densification cycles and showed the symptoms of further gains with additional densification cycles. In contrast, samples that were hot-pressed at moderate pressure and at moderate reinforcement wt%, achieved maximum density within three densification cycles. Furthermore, examination of microstructure revealed the formation of cracks in samples processed at lower pressure and with low reinforcement wt%.

• Carbon letters
• /
• 제1권3_4호
• /
• pp.133-137
• /
• 2001

Mesoporous activated carbon fiber (ACF) was prepared from phenolic resin containing a small amount (0.1 wt %) of organic nickel complex through carbonization and steam activation. Microporous ACF as reference sample was also prepared from phenolic resin without agent. In both cases of the mesoporous ACFs and the microporous ACFs, the electric double layer capacitance of the nonaqueous electrolyte (0.5 M $TEABF_4$/PC or 1.0 M $LiClO_4$/PC) was not proportional to the BET specific surface area. This is owing to the low permeability of nonaqueous electrolyte or the low mobility of ion in narrow micropores. However, the mesoporous ACF showed higher double layer capacitance than the microporous (normal) ACF. This result suggests that the presence of many mesopores promotes the formation of effective double layer or the transfer of ion in the micropore.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제9권3호
• /
• pp.151-155
• /
• 2004

The bioremediation of water system contaminated with phenolic compounds having endocrine-disrupting activity, i.e. 2,4-dichlorophenol, 2,4-dichlorophenoxy acetic acid (2,4-D), and 2,4,5-trichlorophenoxy acetic acid (2,4,5-T), was investigated by using ozone oxidation and activated sludge treatment. Ozone oxidation (ozonation time: 30 min) followed by activated sludge treatment (incubation time: 5 days) was an efficient treatment method for the conversion of phenolic compounds in water into carbon dioxide and decreased the value of total organic carbon (TOC) up to about 10% of initial value. Furthermore, 2,4-D was dissolved in water containing salt, i.e. artificial seawater (ASW), and this water was used as model coastal water contaminated with phenolic compounds. The activated sludge treatment (incubation time: 5 days) could consume significantly organic acids produced from 2,4-D in the model costal water by the ozone oxidation (ozonation time: 30min) and decrease the value of TOC up to about 35% of initial value.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.77-82
• /
• 1999

탄소 fabric 표면을 각기 다른 농도의 인산용액으로 표면처리함으로써 2-D 카본/페놀릭 복합 재료에 미치는 물성과 내 산화성, Arc plasma Torch test를 통하여 내열성등을 알아보았으며 ESCA를 통하여 인산 표면 처리에 의한 표면 functionality를 측정하였다.

• 한국세라믹학회지
• /
• 제52권4호
• /
• pp.284-289
• /
• 2015

This study examined carbon layer coating on silicon carbide (SiC) fibers by utilizing solid-state and wet chemistry routes to confer toughness to the fiber-reinforced ceramic matrix composites, as an alternative to the conventional pyrolytic carbon (PyC) interphase layer. Electrophoretic deposition (EPD) of carbon black nanoparticles using both AC and DC current sources, and the vacuum infiltration of phenolic resin followed by pyrolysis were tested. Because of the use of a liquid phase, the vacuum infiltration resulted in more uniform and denser carbon coating than the EPD routes with solid carbon black particles. Thereafter, vacuum infiltration with controlled variation in phenolic resin concentration, as well as the iterations of infiltration steps, was improvised to produce a homogeneous carbon coating having a thickness of several hundred nanometers on the SiC fiber. Conclusively, it was demonstrated that the carbon coating on the SiC fiber could be achieved using a simpler method than the conventional chemical vapor deposition technique.

• Carbon letters
• /
• 제26권
• /
• pp.107-111
• /
• 2018

• Carbon letters
• /
• 제4권2호
• /
• pp.57-63
• /
• 2003

In polymer precursor based activated carbon, the structure of starting material is likely to have profound effect on the surface properties of end product. To investigate this aspect phenolic resins of different types were prepared using phenol, mcresol and formaldehyde as reactants and $Et_3N$ and $NH_4OH$ as catalyst. Out of these resins two resol resins PFR1 and CFR1 (prepared in excess of formaldehyde using $Et_3N$ as catalyst in the basic pH range) were used as raw materials for the preparation of activated carbons by both chemical and physical activation methods. In chemical activation process both the resins gave activated carbons with high surface areas i.e. 2384 and 2895 $m^2/g$, but pore size distribution in PFR1 resin calculated from Horvath-Kawazoe method, contributes mainly in micropore range i.e. 84.1~88.7 volume percent of pores was covered by micropores. Whereas CFR1 resin when activated with KOH for 2h time, a considerable amount (32.8%) of mesopores was introduced in activated carbon prepared. Physical activation with $CO_2$ leads to the formation of activated carbon with a wide range of surface area (503~1119 $m^2/g$) with both of these resins. The maximum pore volume percentage was obtained in 3-20 ${\AA}$ region by physical activation method.

• 한국항공우주학회지
• /
• 제47권9호
• /
• pp.642-648
• /
• 2019

본 연구에서는 미세 단층 영상을 이용하여 삭마 복합재료의 전산 모델링 및 해석을 수행하였다. 탄소/페놀릭(carbon/phenolic) 복합재료의 삭마 실험은 0.4MW 아크 가열 풍동을 이용하여 수행하였다. 미세 단층 촬영기(Micro-CT)로 삭마 실험 전후의 복합재료 시편을 촬영하여 이진화된 단층 영상을 생성하였다. 생성된 이진화 영상을 활용하여, 삭마 복합재료의 실제 미시 구조가 반영된 전산 모형을 개발하였다. 영상 기반 전산 모형은 시편 횡방향의 특정 영역의 영상을 적층하여 개발하였다. 전산 모형은 실험 전 시편 영상에서 1종, 실험 후 시편 영상에서 8종, 총 9종의 전산 모형을 개발하였다. 영상 기반 전산 모형을 통해 삭마에 의한 유효 물성을 예측하였으며, 기공도 증가에 따른 유효 물성 저하를 확인하였다.

• 한국항공우주학회지
• /
• 제47권6호
• /
• pp.414-421
• /
• 2019

본 논문에서는 재진입 환경에 노출된 탄소/페놀릭 복합재 구조물에 대한 열기계적 연계 해석을 수행하였다. 열기계적 연계를 위한 해석 인터페이스를 상용 소프트웨어를 이용하여 구축하였다. 열분해 및 삭마에 따른 물리적 거동 변화를 모사하기 위해 온도장과 변위장의 주요 지배방정식을 고려하였다. 구축한 해석 인터페이스를 이용하여 탄소/페놀릭 복합재 구조물에 대한 열기계적 연계해석을 수행하였으며 이를 아크 가열 풍동을 이용한 삭마 실험 결과와 비교하였다. 또한 탄소/페놀릭 복합재를 적용한 재진입 캡슐에 대한 열기계적 연계 해석을 수행하였다. 이를 통해 탄소/페놀릭 복합재의 삭마 특성 및 열 보호 효과와 구축한 해석 인터페이스의 활용성을 확인하였다.