• International Journal of Automotive Technology
• /
• 제7권4호
• /
• pp.501-508
• /
• 2006

The effect of chemical additives, such as dimethyl ether(DME), ethanol, carbon disulfide on the soot formation were examined numerically. ill this study, the Frenklach soot mechanism was used as a base mechanism to predict the soot formation in the ethane flame. The combination of Westbrook's DME mechanism, Marinov's ethanol mechanism, and chemical kinetic mechanism for hydrogen sulfide and carbon disulfide flames was made with the base mechanism because the DME, ethanol, $CS_2$ additives are added into the ethane fuel. CHEMKIN code was used as a numerical analysis software to simulate the effect of chemical additives on reduction of the polycyclic aromatic hydrocarbons(PAH's) which are soot precursors. From the numerical results it is observed that addition of DME, ethanol and $CS_2$ into ethane fuel can reduce PAH species significantly. That means theses additives can reduce soot formation significantly. Results also strongly suggest suppression of soot formation by these additives to be mainly a chemical effect. Hand OH radicals may be the key species to the reduction of PAH species for additives.

• 한국안전학회지
• /
• 제25권6호
• /
• pp.9-13
• /
• 2010

An experimental study for characteristics of soot were conducted at the post-flame region in jet diffusion flames, where carbon dioxide was used as additives in oxidizer stream. Light-extinction method was performed using He-Ne laser with wave length at 632.8nm for the measurement of relative soot density and soot volume fraction with dimensionless extinction coefficient, $K_e$ and mass specific extinction coefficient, ${\sigma}_s$. To increase of resolution, laser light was modified for sheet-form using concave, convex lenses and slit. C/H ratio was introduced for quantitative analysis of soot growth which is expressed by carbonization and dehydrogen. Also transmission electron microscopy(TEM) was used for observation of morphological shape. The results show that the relative soot density in the post-flame region was lower when carbon dioxide was added in oxidizer stream because of reduction of flame temperature.

• Tribology and Lubricants
• /
• 제14권4호
• /
• pp.108-113
• /
• 1998

In order to investigate the characteristics of top ring groove deposit formation in diesel engine, engine test and simulation test were performed. From component analysis of used oils sampled from actual running engines, soot content in engine oil was selected as a main parameter for evaluating oil degradation. Deposit formation is highly related to soot content in lubricating oils. And high soot content oil accelerates deposit formation even in low temperature region below 26$0^{\circ}C$. In low temperature region below 26$0^{\circ}C$, deposit formation rate is mainly affected by top ring groove temperature. However, in high temperature region above 26$0^{\circ}C$, deposit formation rate is affected by soot content as well as top ring groove temperature. Therefore, soot content as well as top ring groove temperature should be kept a certain level in order to prevent troubles due to carbon deposit formation.

• 한국화재소방학회논문지
• /
• 제24권6호
• /
• pp.170-175
• /
• 2010

동축류버너를 이용한 제트확산화염에서 이산화탄소의 첨가가 매연 생성에 미치는 영향을 조사하였다. R-타입 열전대를 이용하여 화염대 및 황염과 청염의 경계온도를 측정하였다. 광감쇄법을 이용하여 화염이 존재하는 국소부분에서의 상대적인 매연 농도(1-I/$I_0$)를 측정하였다. 광원으로는 파장이 632.8nm인 He-Ne 레이저가 사용되었고 디텍터를 이용하여 매연입자에 의해 산란과 흡수를 겪은 후의 감쇄된 신호를 직접 측정하였다. 또한, 매연 생성에 있어서의 열적 효과를 알아보기 위해 산화제의 유속을 변화시켜 유속에 의한 영항을 알아보았다. 실험 결과로써, 황염과 청염 각각의 온도는 이산화탄소의 첨가에 따라 점차 낮아졌지만 황염과 청염의 경계온도는 거의 일정하였다. 산화제 측에 이산화탄소를 첨가함에 따라 상대적인 매연 농도는 낮아졌고 이는 산화제의 유속을 증가시켰을 때의 효과와 유사했다. 이것은 화염온도의 저하와 매연입자의 체류시간 감소에 기인하는 것으로 생각된다. 또한 이산화탄소의 첨가가 화염의 불안정성을 야기하여 순수 에틸렌/공기 화염에 비해 화염의 길이가 다소 증가하는 것으로 나타났다.

• 대한기계학회논문집B
• /
• 제29권12호
• /
• pp.1335-1343
• /
• 2005

The calibration technique of Time Resolved Laser Induced Incandescence was investigated both experimentally and numerically by using standard-sized carbon black particles for the instantaneous soot measurement at exhaust tail pipe in engine. The carbon black particles (19nm, 25nm, 45nm and 58nm) used in this study are similar, though not identical, to soot particle generated from flame not only in morphology but also in micro-structure. The amount of soot loading in flow was controled by a diluted gas (nitrogen) and was measured by the gravimetric method at exhaust pipe in calibrator. The successful calibrations of primary particle size and soot mass fraction were carried out at the range from 19nm to 58nm and from $0.25mg/m^3$ to $37mg/m^3$ respectively. And based on these results the numerical simulation of LII signal was tuned and the effect of an exhaust temperature variation on the decay rate of LII signal was corrected.

• Carbon letters
• /
• 제10권1호
• /
• pp.5-8
• /
• 2009

We measured the non-carbon content of single-walled carbon nanotubes (SWCNTs) in SWCNT soot using thermogravimetric analysis. The weight increased percentage by the oxidation of metal in the raw soot is well obtained by TGA graph which was confirmed with ICP-AES, XRD, and XPS. This work will be very useful for the purity precise evaluation of SWCNT with UN-vis-NIR spectroscopy.

• Tribology and Lubricants
• /
• 제19권5호
• /
• pp.251-258
• /
• 2003

New method and device for the on-line measurement of soot concentration in a diesel engine oil are proposed, where the measurement principle is based mainly on attenuated internal total reflection. The detector were evaluated in various ranges of contaminated oils by carbon black particles. It was found that the proposed detector could be well used to monitor the oil deterioration due to soot contamination. Operational range of the detector was found from 0 to 5 mass percentage of soot content. Test results with water and fuel dilution showed that these effects were not remarkable. However, adsorption of carbon black particles onto the measurement surface was considered to be a critical problem of the detector. Effects of particle deposition on the interface was experimentally evaluated with the oil temperature and flow turbulence and discussed throughout this work.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1158-1161
• /
• 2004

Shell shaped hollow carbon nanoparticles are synthesized in the oxygen-hydrogen diffusion flame with $C_{2}H_{2}$ as precursor when it is irradiated with $CO_{2}$ laser of certain power. Below this power of laser, we couldn't get any other but amorphous soot. This shell shaped hollow carbon nanoparticles shows outer wall of high degree of crystallinity with void space inside of itself. And size distribution of these nanoparticles is measured with TEM image analysis. Also the structural comparison between this carbon nanoparticle and soot is done by Raman and XRD measurement. These results show this carbon nanoparticles are of grapheme structure, which means it has good crystallinity when compared with soot.

• 대한기계학회논문집B
• /
• 제24권7호
• /
• pp.1002-1009
• /
• 2000

Among the various types of diesel after-treatment device, the corona discharge reactor may be considered as a powerful process for trapping submicron particles. But after precipitation on the electrodes occurs, the reentrainment of particles is severe and often causes low or negative precipitation efficiency. Experiments were performed to investigate the effect of an applied voltage on the reentrainment of soot particles from the electrodes. A co-annular laminar diffusion flame burner was used as the soot generator. When a highly negative voltage was applied, exfoliation of the deposited soot particles and an increase in concentration of particles smaller than approximately 150 nm were observed. Turbulence induced from the negative tuft corona and sputtering caused particle reentrainment from the corona wire and from plates as well. Under soot laden combustion gas, a streamer corona often occurred in the wire-cylinder reactor. Because of its transient nature, streamer corona violently increased the concentration of reentrained particles and CO gas.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제33회 KOSCO SYMPOSIUM 논문집
• /
• pp.299-303
• /
• 2006

From the analysis of fly ash, which contains unburned carbon, collected from the coal-fired Yong Hung power station, most particles are turned out to be hollow cenosphere and agglomerated soot particles. The sooting potential from six coals used in the plant were investigated with CPD model. The results show that the higher potential presented to Peabody, Arthur, Shenhua coals rather than other coals. It is necessary to measure the coal flow rates at each coal feeding pipe for four burner levels since they affect the extent of mixing of soot with oxidant, in turn, the oxidation rate of soot particles. The unbalance in coal flow rate was found in several coal pipes. We successfully reduced unburned carbon in ash by increasing the excess air and changing the SOFA yaw angle.