• Applied Chemistry for Engineering
• /
• v.29 no.5
• /
• pp.594-603
• /
• 2018

The effects of operating conditions such as benzene concentration, nitrogen flow rate, steam flow rate, and bed temperature on TSA process were experimentally investigated as a potential VOC removal technology using two kinds of beds packed with activated carbon and zeolite 13X. The TSA cycle studied was composed of the adsorption step, steam desorption step, and drying and cooling step. At 2% benzene concentration, the total adsorption amounts of zeolite 13X and activated carbon were 4.44 g and 3.65 g, respectively. Since the zeolite 13X has a larger packing density than that of the activated carbon, the larger benzene amount could be adsorbed in a single cycle. Increasing the water vapor flow rate to 75 g/hr at 2% benzene concentration reduced the desorption time from 1 hr to a maximum of 33 min. If the desorption time is shortened, the drying and cooling step period can be relatively increased. Accordingly, the steam removal and bed cooling could be sufficiently performed. The desorption amounts increased with the increase of the bed temperature. However, the energy consumption increased while the desorption amount was almost constant above $150^{\circ}C$. In the continuous cycle process, when the amount of remained benzene at the completion of the regeneration step increased, it might cause a decrease in the working capacity of the adsorbent. The continuous cycle process experiment for zeolite 13X showed that the amount of remained benzene at the end of regeneration step maintained a constant value after the fourth cycle.

• Journal of the Korean Ceramic Society
• /
• v.33 no.8
• /
• pp.935-941
• /
• 1996

Two-dimensional carbon/carbon preforms made of PAN-based carbon yarn and phenolic resin were densified with pyrolysis of propane by pulse chemical vapor infiltration where repeated the cycle of gas introduction residence and evacuation. Maximim density increment was 14% when infiltration temperature and time were 100$0^{\circ}C$ and 21.25 hrs respectively. The distribution of deposits of pyrocarbon by this process has been occurred uniformly in the bottom middle and top of carbon/carbon composite preform Pulse CVI with residence is most effective in increasing density and shortening infiltration time among isothermal CVI and pulse CVI with and without residence.

• Journal of Korean Society of Water and Wastewater
• /
• v.25 no.4
• /
• pp.511-517
• /
• 2011

To evaluate carbon emission in water treatment processes, LCA (life cycle assessment) was applied to 8 multi-regional water treatment plants (WTPs) from intake to supply of tap water. Investigation of 8 WTPs revealed that average carbon emission for 1 $m^3$ of tap water was 221 g. Major carbon emission sources in water supply system were intake and supply processes. Meanwhile, mixing process was the main carbon emission source in unit water treatment processes. Carbon emission was proportional to the turbidity and COD of raw water. Intake of better raw water and minimization of energy consumption in unit processes are needed to reduce carbon emission in the WTPs. In addition, comparison of carbon emission among WTPs can be used as a parameter for optimization of operation and maintenance of water treatment processes.

• Journal of the korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.36-44
• /
• 1984

The prediction of the emission concentrations in 4-cycle 4-cylinder spark ignition engine is made by considering the model with the extended Zedovich mechanism. The predicted values for nitric oxide, carbon dioxide and carbon monoxide agree with the experimentally measured ones.

• Proceedings of the KSEEG Conference
• /
• 2002.04a
• /
• pp.91-91
• /
• 2002

• Korean Chemical Engineering Research
• /
• v.55 no.3
• /
• pp.363-368
• /
• 2017

Methylotrophy is able to use reduced one-carbon compound, such as methanol and methylamine, as a sole carbon source. Methylobacterium extorquens AM1 is the most extensively studied methylotroph utilizing serine-isocitrate lyase cycle. Because the Poly 3-hydroxybutyrate (PHB) synthesis pathway in M. extorquens AM1 is likely to interlink with EMCP (ethylmalonyl-CoA pathway), glyoxylate, and TCA cycles, regulation of PHB production is needed to produce EMCP-derived acid or TCA acids. To adjust carbon flux to PHB production, PhaR, which seems to have function of regulator of PHB synthesis and acetyl-CoA flux, was knocked out in M. extorquens AM1 by using markerless gene deletion methods. As a result, PHB granules were remarkably reduced in the knockout strain ${\Delta}phaR$ compared to parental strain. Although lag phase was extended for 12h, ${\Delta}phaR$ showed similar cell growth and methanol consumption rate compared to wild type.

• Applied Chemistry for Engineering
• /
• v.26 no.1
• /
• pp.80-85
• /
• 2015

Silicon/carbon composites as anode materials for lithium-ion batteries were examined to find the cycle performance and capacity. Silicon/carbon composites were prepared by a two-step method, including the magnesiothermic reduction of SBA-15 (Santa Barbara Amorphous material No. 15) and carbonization of phenol resin. The electrochemical behaviors of lithium ion batteries were characterized by charge/discharge, cycle, cyclic voltammetry and impedance tests. The improved electrochemical performance attributed to the fact that silicon/carbon composites suppress the volume expansion of the silicon particles and enhance the conductivity of silicon/carbon composites (30 ohm) compared to that of using the pure silicon (235 ohm). The anode electrode of silicon/carbon composites showed the high capacity approaching 1,348 mAh/g and the capacity retention ratio of 76% after 50 cycles.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.6
• /
• pp.382-390
• /
• 2012

Global warming has been hot issue world wide. Korea has been dealing with the global issue under the slogan of low carbon and green-growth such as setting national greenhouse gas (GHG) reduction targets and allocation to each industrial sector. Infrastructure construction, in which enormous social overhead capital (SOC) is input, has great role as one of the actions. Road is one of the representative infrastructure and large amount of resources is utilized in its construction, operation and maintenance stage. The estimation methodology of life cycle carbon emissions was developed and applied to a case study of highway currently under construction in this study. Also, total carbon emissions of all the highway in South Korea at present (2009) and cumulative carbon emissions from 2009 to 2020 were estimated using the results of case study.

• Carbon letters
• /
• v.25
• /
• pp.84-88
• /
• 2018

At present, an important research area is the search for materials that are compatible with CMOS technology and achieve a satisfactory response rate and modulation efficiency. A strong local field of graphene surface plasmon polariton (SPP) can increase the interaction between light and graphene, reduce device size, and facilitate the integration of materials with CMOS. In this study, we design a new modulator of SPP-based cycle branch graphene waveguide. The structure comprises a primary waveguide of graphene-$LiNbO_3$-graphene, and a secondary cycle branch waveguide is etched on the surface of $LiNbO_3$. Part of the incident light in the primary waveguide enters the secondary waveguide, thus leading to a phase difference with the primary waveguide as reflected at the end of the branch and interaction coupling to enhance output light intensity. Through feature analysis, we discover that the area of the secondary waveguide shows significant localized fields and SPPs. Moreover, the cycle branch graphene waveguide can realize gain compensation, reduce transmission loss, and increase transmission distance. Numerical simulations show that the minimum effective mode field area is about $0.0130{\lambda}^2$, the gain coefficient is about $700cm^{-1}$, and the quality factor can reach 150. The structure can realize the mode field limits of deep subwavelength and achieve a good comprehensive performance.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.15 no.1
• /
• pp.34-45
• /
• 2007

In order to reduce the compression power and to use the overall energy contained in LNG effectively, a combined cycle is devised and simulated. The combined cycle is composed of two cycles; one is an open cycle of liquid/solid carbon dioxide production cycle utilizing LNG cold energy in $CO_2$ condenser and the other is a closed cycle gas turbine which supplies power to the $CO_2$ cycle, utilizes LNG cold energy for lowering the compressor inlet temperature, and uses the heating value of LNG at the burner. The power consumed for the $CO_2$ cycle is investigated in terms of a solid $CO_2$ production ratio. The present study shows that much reduction in both $CO_2$ compression power (only 35% of the power used in conventional dry ice production cycle) and $CO_2$ condenser pressure could be achieved by utilizing LNG cold energy and that high cycle efficiency (55.3% at maximum power condition) in the gas turbine could be accomplished with the adoption of compressor inlet cooling and regenerator. Exergy analysis shows that irreversibility in the combined cycle increases linearly as a solid $CO_2$ production ratio increases and most of the irreversibility occurs in the condenser and the heat exchanger for compressor inlet cooling. Hence, incoming LNG cold energy to the above components should be used more effectively.