• Journal of the Korean Institute of Gas
• /
• v.18 no.3
• /
• pp.13-19
• /
• 2014

Dynamic ductile fracture (DDF) has been studied in the transportation pipeline for the carbon dioxide capture and storage(CCS) system. DDF behavior of CCS transportation pipeline has been analyzed using Battelle Two Curve Method (BTCM) and compared with the DDF behavior of natural gas pipeline. The operating safety criteria against the DDF has been investigated based on the sensitivity analyses of the pipe thickness and the operating temperature for the $CO_2$ pipeline. The DDF criteria can be applied to confirm the operating safety of the $CO_2$ pipeline. If the commercial natural gas pipeline were used at room temperature as a $CO_2$ pipeline, the thickness of pipe should be at least 7mm and the pressure should be less than 54bar for the $CO_2$ pipeline system.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.6
• /
• pp.21-27
• /
• 2019

Cellulose-based carbon fabrics are used in aerospace nozzles have low thermal conductivity and high ablation resistance. However, there is a disadvantage in that the weight is reduced by 70~90% in the pyrolysis process and graphitization process and the residual rate is low when the final carbon fabric is produced. In this study, phosphoric acid as a phosphorus flame retardant and Citric acid as a cross-linking agent were treated on the lyocell fabrics. After that the functional groups were identified and thermal properties were confirmed by FT-IR, XRD and TGA. The yields of the final carbon fabrics were also compared through the pyrolysis and graphitization process. The graphitized yield increased to 8.1% with increasing citric acid to 16 wt% added.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.4
• /
• pp.55-60
• /
• 2002

This paper presents a technique for the preparation of vertically grown CNTs by ICPHFCVD(inductively coupled plasma hot filament chemical vapor deposition) below $580^{\circ}C$. Purification of the CNTs(carbon nanotubes) using RE(radio frequency) plasma in a one step process, based on the different etching property of the Ni-tip, amorphous carbon and carbonaceous materials is also discussed. After purifying the grown materials. CNTs shown the multi walled and hollow typed structure. The typical outer and inner diameters or CNT were 50 nm and 25 nm, respectively. The graphitic wall was composed of 82 layers and the distance between wall and wall was 0.34 nm. From the results of TEM observation, the Ni catalyst at the tip of the carbon nanotubes were effectively removed by using a RF plasma etching, continuously.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.5
• /
• pp.36-42
• /
• 2019

In this study, the pre-treatment of lyocell fabrics was performed using phosphoric acid (PA) as a phosphorus flame retardant and melamine resin (MR) as a cross-linking agent to fabricate carbon fabrics using lyocell fibers. The physical and chemical changes were investigated by thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT-IR), X-ray diffractometry (XRD) and weight analysis. We confirmed that the weight yield of the carbon fabrics compared to the untreated fabrics increased by 14.7%, and width and length yield of the fabrics increased by 15% and 15.5%, respectively. This may be due to the effect of promoting the dehydration reaction of cellulose, forming char on the fiber surface, which induces a crosslinking reaction in the cellulose molecule and stabilizes the structure upon pyrolysis.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.4
• /
• pp.458-464
• /
• 2021

Lithium ion batteries (LIBs) is a kind of rechargeable secondary battery, developed from lithium battery, lithium ions move between the positive and negative electrodes to realize the charging and discharging of external circuits. Zeolitic imidazolate frameworks (ZIFs) are porous crystalline materials in which organic imidazole esters are cross-linked to transition metals to form a framework structure. In this article, ZIF-67 is used as a sacrificial template to prepare nano porous carbon (NPC) coated cobalt nanoparticles. The final product Co/NPC composites with complete structure, regular morphology and uniform size were obtained by this method. The conductive network of cobalt and nitrogen doped carbon can shorten the lithium ion transport path and present high conductivity. In addition, amorphous carbon has more pores that can be fully in contact with the electrolyte during charging and discharging. At the same time, it also reduces the volume expansion during the cycle and slows down the rate of capacity attenuation caused by structure collapse. Co/NPC composites first discharge specific capacity up to 3115 mA h/g, under the current density of 200 mA/g, circular 200 reversible capacity as high as 751.1 mA h/g, and the excellent rate and resistance performance. The experimental results show that the Co/NPC composite material improves the electrical conductivity and electrochemical properties of the electrode. The cobalt based ZIF-67 as the precursor has opened the way for the design of highly performance electrodes for energy storage and electrochemical catalysis.

• Tribology and Lubricants
• /
• v.38 no.3
• /
• pp.101-108
• /
• 2022

The structure and properties of tetrahedral amorphous carbon (ta-C) coatings depend on the main process parameters and bending angles of the magnetic field filter used in the filtered cathodic vacuum arc (FCVA). During the process, it is possible to effectively control the plasma flux of carbon ions incident on the substrate by controlling the arc discharge current, thereby influencing the mechanical properties of the coating film. Furthermore, we can control the size and amount of large particles mixed during carbon film formation while conforming with the bending angle of the mechanical filter mounted on the FCVA; therefore, it also influences the mechanical properties. In this study, we consider tribological characteristics for filtered bending angles of 45° and 90° as a function of arc discharge currents of 60 and 100 A, respectively. Experiment results indicate that the frictional behavior of the ta-C coating film is independent of the bending angle of the filter. However, its sliding wear behavior significantly changes according to the bending angle of the FCVA filter, unlike the effect of the discharge current. Further, upon changing the bending angle from 45° to 90°, abrasive wear gets accelerated, thereby changing the size and mixing amount of macro particles inside the coating film.

• Journal of Convergence for Information Technology
• /
• v.12 no.4
• /
• pp.338-344
• /
• 2022

It is necessarily required in developing Si-based anode materials for lithium ion batteries, and the related researches are actively working especially in Si-carbon composite material. On the other hand, the photovoltaic and semiconductor industries discard huge amount of Si resources, facing the environmental issue. In this study, recycled Si resource is adopted to obtain Si-carbon composite for LIB(Lithium-Ion Batteries). In order to improve high-capacity retention characteristics and cycle stability of a Si anode material for the LIB, two differenct composites having a mass ratio of silicon and pitch of 1:1 and 2:1 are synthesized and electrochemical characteristics of the anode material manufactured by simple self-assembly method. This result in excellent initial capacity with stable cycle life, and confirming the potential use of recycled Si material for LIB.

• Composites Research
• /
• v.36 no.3
• /
• pp.154-161
• /
• 2023

This study explored the feasibility of replacing a metal link with a carbon fiber/epoxy composite link and assessed its capacity to withstand a given load condition using failure criteria. The micromechanics of failure (MMF) criterion was employed to predict the failure mode of the composite material, and mechanical tests were conducted to obtain reference strength parameters for MMF. The findings revealed that the stress distribution was concentrated near the hole, and weaknesses were found around the hole and at the end of the link under bending conditions. Based on the failure index, matrix tensile failure was predicted at the end of the link, and fiber compression failure occurred near the hole. The methods and results obtained from this study can provide valuable guidelines for assessing the safety of composite materials under specific load conditions when replacing metal parts with carbon fiber/epoxy composites to achieve weight reduction.

• Applied Chemistry for Engineering
• /
• v.18 no.3
• /
• pp.199-204
• /
• 2007

Nanomedicine is a young and rapidly emerging field, which integrates clinical medicine with nanotechnology. Although the commercial nanomedicine is still in a fairly embryonic state, the recent advances in the nanotechnology-based therapeutics and diagnosis has changed the landscape of medicine. Bibliometric analysis shows a surge in research activity over the past decade. In this review, we have discussed some of the promising materials and their applications to this nascent field, such as carbon nanomaterials, polymeric drug delivery systems, and diagnostic imaging agents.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.1000-1002
• /
• 2012

The material with superior biocompatibility and physical-chemical stability is required to fabricate high sensitive biosensors. Many kinds of biomaterials have been evaluated to apply for bioindustry. Recently, carbon based diamond and graphene thin films have been focal pointed as bio applications and their possibility is partially evaluated. Diamond thin film has many advantages for electrochemical and biological applications, such as wide potential window (3.0~3.5V), low background current and chemical-physical stability. And graphene film has many advantages as biomaterial, chemical-physical stability and conductivity. In this work, we have cultured human nerve cell (SH-SY5Y) on the nanocrystalline diamond, mirocrystalline diamond, graphene film and cell culture dish. We use MTT assay to evaluate the characteristics of cell culture on the substrates. As a result, nerve cell is well cultured on the carbon based diamond and graphene films as similar as cell culture dish. We expect that carbon materials have been applied for bioindustry such as biosensors.