• Elastomers and Composites
• /
• v.33 no.1
• /
• pp.44-51
• /
• 1998

The purpose of this experiments were investigated on the physical properties of rubber com-pounds containing two types carbon black. Bound rubber and interaction coefficient for com-pounds with pure carbon black were higher than those for the compounds with dual phase carbon black. Slightly higher values in 300% modulus and tensile strength indicated that the ratio of rubber-filler bound to rubber-rubber bound of pure carbon black were higher than those of com-pounds with dual phase carbon black. It was founded that dynamic properties, that is rebound, heat build-up, 0 & $60^{\circ}C$ tan $\delta$, and cut and chip loss of compounds with dual phase carbon black were better than those of compounds with pure carbon black, but abrasion property of dual phase carbon black was lower than those of pure carbon black because of low reinforcing ability.

• Composites Research
• /
• v.24 no.5
• /
• pp.34-38
• /
• 2011

Carbon nanotubes (CNTs) have been widely investigated as reinforcements of CNT/polymer nanocomposites to enhance mechanical and electrical properties of polymer matrices since their discovery in the early 90's. Furthermore, the number of studies about incorporating CNTs into carbon fiber reinforced plastics (CFRP) to reinforce their polymer matrices is increasing recently. In this study, single-walled carbon nanotubes (SWNT) were dispersed in epoxy with 0.2 wt.% and 0.5 wt.%. Then, the SWNT/epoxy mixtures were processed to carbon fiber composites by a vacuum assisted resin transfer molding (VARTM) and a wet lay up method. The processed composite samples were tested for the interlaminar shear strength (ILSS). The relationship between the interlaminar shear strengths and processing, and the reinforcement mechanism of carbon nanotubes were investigated. CNT/epoxy nanocomposite specimens showed the increased tensile properties. However, the ILSS of carbon fiber composites was not enhanced by reinforcing the matrix with CNTs because of processing issues caused by increased viscosity of the matrix due to addition of CNTs particularly for a VARTM method.

• Journal of Adhesion and Interface
• /
• v.14 no.2
• /
• pp.82-87
• /
• 2013

Preliminary studies on the synthesis of magnetic nanoparticles including nanoporous carbon materials have been done via a direct carbonization process from resol, ferric nitrate and triblock copolymer F127. The results show that the nanoporous magnetite/carbon ($Fe_3O_4$/carbon) with a low $Fe_3O_4$ content (1 wt%) possesses an ordered 2-D hexagonal (p6mm) structure, uniform nanopores (3.6 nm), high surface areas (up to 635 $m^2/g$) and pore volumes (up to 0.48 $cm^3/g$). Magnetite nanoparticles with a small particle size (10.2 nm) were confined in the matrix of amorphous carbon frameworks with superparamagnetic property (7.7 emu/g). The nanoporous magnetite/carbon showed maximum adsorption amount (995 mg/g) of ibuprofen after 24 h at room temperature. The nanoporous magnetite/carbon was separated from solution easily by using a magnet. The nanoporous magnetite/carbon material is a good adsorbent for hydrophobic organic drug molecules, i.e. ibuprofen.

• Journal of Korean Society for Atmospheric Environment
• /
• v.31 no.2
• /
• pp.173-180
• /
• 2015

The purpose of this study was to fabricate a ferric nitrate impregnated activated carbon, and the performance for hydrogen sulfide by adsorption was evaluated. Sodium hydroxide was utilized to control pH in the process during generation of ferric hydroxide on the surface of the carbon. Critical mixing duration for generation of ferric hydroxide on the carbon was 48 hrs at pH 1 of the solution, in which the chemical adsorption of hydrogen sulfide was enhanced. The adsorption capacity of the impregnated carbon increased up to 0.10 g hydrogen sulfide/g carbon, which was 4.3 times higher than that of the raw carbon. Presence of FeOOH on the surface of the impregnated carbon was examined by X-ray diffraction.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.198-203
• /
• 1999

2D carbon/carbon composites have been prepared with and without addition of 1, 3 and 5wt% of oxidation inhibitor boron and then heat teated up to 1700, 2000, 2300, 2600 each. This paper presents the effects of boron on the mechanical properties of 2D C/C composites in terms of the acceleration of graphitization and also discussed about the retardation of air oxidation.

• Carbon letters
• /
• v.14 no.3
• /
• pp.145-151
• /
• 2013

Graphene is a fascinating material with excellent electrical, optical, mechanical, and chemical properties. Remarkable progress has been made in the development of methods for synthesizing large-area, high-quality graphene. Recently, the chemical vapor deposition method has opened up the possibility of using graphene for electronic devices and other applications. This review covers simple and inexpensive methods to grow graphene using polymers as solid carbon sources; which do not require an additional process to transfer graphene from the growth substrate to the receiver substrate.

• Journal of Environmental Science International
• /
• v.11 no.8
• /
• pp.773-781
• /
• 2002

The natural carbon cycle has been perturbed since the mid-19th century by anthropogenic CO$_2$emissions from fossil fuel combustion and deforestation due to population growth and industrialization. The current study simulated the global carbon cycle for the past 42 years using an eight-box carbon cycle model. The results showed that since the terrestrial biospheric carbon sink was roughly offset by the deforestation source, the fossil fuel emission source was partitioned between the atmospheric and oceanic sinks. However, the partitioning ratio between the atmosphere and the ocean exhibited a change, that is, the carbon accumulation rate was faster in the atmosphere than in the ocean, due to a decrease in the so-called ocean buffering capacity. It was found that the ocean buffering capacity to take up excess CO$_2$decreased by 50% in terms of the buffer factor over the past 42 years. Accordingly, these results indicate that if the current CO$_2$emission trend continues, the future rate of increase in the atmospheric CO$_2$concentration will accelerate.

• Journal of the Korean Ceramic Society
• /
• v.37 no.6
• /
• pp.569-575
• /
• 2000

Fabrication of carbon fiber reinforced composites was carried out by hand lay-up method. Carbon nanofibers and SiC nanofibers were used as filler in the composites fabrication. Carbon nanofibers, one of the new carbon materials, have 5∼500 nm in diameter and 5-10 nm in length. SiC nanofibers were modified by silicon monoxide vapor with carbon nanofibers. The composites were carbonized at 1000$^{\circ}C$ in a nitrogen atmosphere, and then densified by molten pitches impregnated in vacuum. Multiple cycles of liquid pitch impregnation and carbonization were carried out to obtain a desired density. The composites were characterized by density, microstructure. The inter-laminar shear strength (ILSS) test was performed for mechanical properties. For the new application, the microwave reflective proeprty of composites was investigated. Dielectric constant and permeability spectrum were measured in 12∼18 GHz frequency ranges. On the basis of the wave propagation theory in a lossy media, the reflection loss from the composite inter-layer was predict as a function of frequency.

• Journal of Energy Engineering
• /
• v.11 no.1
• /
• pp.34-46
• /
• 2002

Carbon accounting is a key issue in the discussions on global warming/CO$_2$mitigation. This paper applies both the IPCC Approach and the NEAT (Non-Energy use Emission Accounting Tables) model, a bottom-up approach, to estimate the potential CO$_2$ emissions (carbon storage) originating from the non-energy use as to assess the actual CO$_2$ emissions (carbon release) from the use of fossil fuels in Korea. The current Korean carbon accounting seems to overestimate the potential CO$_2$ emissions and with it to underestimate the actual CO$_2$ emissions. The estimation shows that the potential CO$_2$ emissions calculated according to the IPCC Approach are lower than those calculated using the NEAT model. This is because the IPCC default storage fraction for naphtha seems to be low for the Korean petrochemical production structure, on the one hand and because the IPCC Approach does not consider the trade with short life petrochemical products, on the other hand. This paper shows that a bottom-up approach like the NEAT model can contribute to overcome some of limitations of the IPCC guidelines, especially by considering the international trade with short life petrochemical products and by estimating the storage fractions of fossil fuels used as feedstocks for the country in consideration. This paper emphasizes the importance of accurate energy statistics for carbon accounting.

• Nuclear Engineering and Technology
• /
• v.47 no.5
• /
• pp.579-587
• /
• 2015

To support the use of nuclear power as a sustainable electric energy generating technology, long-term supply of uranium is very important. The objective of this research is to investigate the use of new adsorbent material for cost effective uranium extraction from seawater. An activated carbon-based adsorbent material is developed and tested through an electrosorption technique in this research. Adsorption of uranium from seawater by activated carbon electrodes was investigated through electrosorption experiments up to 300 minutes by changing positive potentials from +0.2V to +0.8V (vs. Ag/AgCl). Uranium adsorption by the activated carbon electrode developed in this research reached up to 3.4 g-U/kg-adsorbent material, which is comparable with the performance of amidoxime-based adsorbent materials. Electrosorption of uranium ions from seawater was found to be most favorable at +0.4V (vs. Ag/AgCl). The cost of chemicals and materials in the present research was compared with that of the amidoxime-based approach as part of the engineering feasibility examination.