• The Journal of Engineering Geology
• /
• v.30 no.4
• /
• pp.541-555
• /
• 2020

The grouting method is used for reinforcing and waterproofing the soft ground, increasing the bearing capacity of structures damaged by lowering or subsidence due to rise and vibration, and for ordering. This study attempted to develop a blast furnace slag-based cementless grout material to increase the strength and hardening time of the grout material using reinforcing fibers. In this regard, in this study, it was used in combination with calcium hydroxide, which is an alkali stimulant of the three fine powders of blast furnace slag, and the content of calcium hydroxide was used by substituting 10, 20, and 30% of the fine powder of blast furnace slag. In addition, in order to compare the strength according to the presence or absence of reinforcing fibers, an experiment was performed by adding 0.5% of each fiber. As the content of carbon fibers and aramid fibers increased, the uniaxial compressive strength increased, and it was confirmed that the crosslinking action of the fibers in the grout material increased the uniaxial compressive strength. In addition, it was confirmed that the gel time sharply decreased as the content of the alkali stimulate increased.

• Journal of the Institute of Convergence Signal Processing
• /
• v.23 no.1
• /
• pp.28-36
• /
• 2022

Currently, the automation and intelligence of the shipbuilding industry have improved its work production capacity and cost competitiveness, but the reduction rate of safety accidents among industrial site workers is still low and the damage caused by safety accidents is very serious, so there is a need for improvement according to the workplace. This research aims to demonstrate the connectivity between smart safety helmets in the demonstration area to verify the effectiveness along with the development of smart helmets for worker protection and environmental safety in shipyards. For efficient communication between workers, impact noise of over 95dB was confirmed in the workplace, and noise reduction was required. To solve this problem, the filtering performance was compared and analyzed using the Butterworth, Chebyshev, and elliptic algorithms. The connectivity test and noise reduction method between smart helmets proposed in this study will increase the usability and safety of the field through the development of advanced smart helmets tailored to the shipbuilding workplace in the future.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.1
• /
• pp.45-52
• /
• 2023

The power generation method using expensive diesel has operation problems such as high cost diesel generator and a lack of reserved power due to increase of power demand in some islands, requiring expansion of power generation facilities. To solve this problems, it is necessary to improve the efficiency of power generation facilities through an ORC(Organic Rankin Cycle) system application that uses waste heat as a heat source. Therefore, localized application technology of price competitive and highly reliable ORC power generation system is needed, and optimization technology of generators is having great effect, so this study performed two generator designs to get a high-efficiency generator with an optimized 30kW output. The comparison of simulation data for two designed models showed that a generator with SPM factor of 46.2% had an efficiency of 92.1% and a power ouput of about 23.2kW based on 12,000rpm, a generator with SPM factor of 44.46%, had a power output of 27.9kW and efficiency of 93.6% based on above rpm. For the verification of improved design model with SPM factor of 44.46%, the prototype test system with 110kW motor dynamometer was installed and got to the efficiency of 92.08% with conditions of the rated capacity 25kW at 12,000rpm, the test results of prototype generator showed the validity of generator design.

• Animal Bioscience
• /
• v.36 no.10
• /
• pp.1612-1618
• /
• 2023

Objective: In our previous study, we observed that the addition of waste cooking oil (WCO) reduced ammonia (NH₃) emissions during laboratory-scale composting of dairy cattle manure under low-aeration condition. Therefore, this study aimed to evaluate the effect of addition of WCO on NH₃ emissions reduction during pilot-scale composting of dairy cattle manure, which is close to the conditions of practical composting treatment. Methods: Composting tests were conducted using pilot-scale composting facilities (1.8 m³ of capacity). The composting mixtures were prepared from manure, sawdust, and WCO. Two treatments were set: without WCO (Control) and with WCO added to 3 wt% of manure (WCO3). Composting was conducted under continuous aeration at 40 L/min, corresponding to 22.2 L/(min·m³) of the mixture at the start of composting. The changes in temperatures, NH₃ concentrations in the exhaust gases, and contents of the composted mixtures were analyzed. Based on these analysis results, the effect of WCO addition on NH₃ emissions and nitrogen loss during composting was evaluated. Results: During composting, the temperature increase of the composting mixture became higher, and the decreases of weight and water content of the mixture became larger in WCO3 than in Control. In the decrease of weight, and the residual weight and water content of the mixture, significant differences (p<0.05) were detected between the two treatments at the end of composting. The NH₃ concentrations in the exhaust gases tended to be lower in WCO3 than in Control. Nitrogen loss was 21.5% lower in WCO3 than in Control. Conclusion: Reduction of NH₃ emissions by the addition of WCO under low aeration condition was observed in pilot-scale composting, as well as in laboratory-scale composting. This result suggests that this method is effective in reducing NH₃ emissions in practical-scale composting.

• Analytical Science and Technology
• /
• v.19 no.5
• /
• pp.383-388
• /
• 2006

Simple post-wash method by ion chromatography (IC) was established for the rapid and precise determination of fluoride ion in wastewater from mine in fluorite mineralized area. High sulfate in sample was retained in a pre-column and less strongly held fluoride ion was transferred to the principal separation system using modified conventional IC with switching technique. An analytical column with high capacity (AS 9 HC) was used as a pre-column to retain the amount of high sulfate. A guard column (AG 14) as a separation column was used to increase the response of fluoride and reduce the system pressure. According to the recovery of fluoride ion with one detector and the observation of sulfate peak with another conductivity detector, the optimum switching time of 10-port chromatographic injector was 4.3 min. The limit of detection (S/N = 3) of fluoride in synthetic solution containing $500mg\;L^{-1}$ sulfate was $2.4{\mu}g/L$, with $25{\mu}L$ sample volume.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.6A
• /
• pp.513-523
• /
• 2010

For continuous I-girder bridges, a large negative bending moment is generated near pier region so that plastic hinge is first formed at this point. Then, the bending moment is redistributed when the I-girder has enough flexural ductility (or rotational capacity). However, for I-girder with high strength steel, it is known that the flexural ductility is considerably decreased by increasing the yield strength of material. Thus, it is necessary to conduct a study for guaranteeing proper flexural ductility of I-girder with high-strength steel. In this study, the evaluation of flexural ductility of negative moment region of I-girder with high strength steel where yield stress of steel is 680 MPa is presented based on the results of finite element analysis and experiment. From the results, it is found that the flexural ductility of the I-girder is significantly reduced due to the increase of elastic deformation and the decrease of plastic deformation ability of the material when the yield strength increases. In this study, the method to improve the flexural ductility of I-girder with high strength steel is proposed by an unequal installation of cross beam and an optimal position of cross beam is also suggested. Finally, the effects of the unequal installation of cross beam on the flexural ductility are discussed based on the experimental results.

• Journal of the Korean Geotechnical Society
• /
• v.40 no.1
• /
• pp.29-37
• /
• 2024

In this study, recycled concrete aggregates (RCA) were treated in a 5-kg-scale prototype reactor with carbon dioxide (CO₂) to enhance their material quality and geotechnical performance. The aggregate crushing value (ACV) and California bearing ratio (CBR) were measured on untreated RCAs and CO₂-treated RCAs. After CO₂ treatment, the ACV decreased from 35.6% to 33.2%, and the CBR increased from 97.5% to 102.4%. The CO₂ treatment caused a reduction of fine particle generation and an increase in bearing capacity through carbonation. When CO₂ treatment was performed with mechanical agitation, which provided additional enhancement in mechanical quality, the ACV was reduced further to 30.3%, and the CBR increased to 137.7%. If upscaled effectively, the proposed CO₂ treatment technique would be an effective method to reduce carbon emissions in construction industries.

• Korean Journal of Animal Reproduction
• /
• v.26 no.3
• /
• pp.215-221
• /
• 2002

Antioxidants(N-acetyl-1-cysteine, ebselen and glutathione) and growth factors(EGF, PDGF) were studied as a mean of increasing the development of porcine embryos produced by in vitro maturation (IVM) and in vitro fertilization(IVF). Porcine embryos developed to the 2~8 cell stage after IVF were cultured fer 6 to 7 days at 38.5$^{\circ}C$ in NCSU 23 medium containing antioxidants plus growth factors. Cell numbers of blastocysts were counted by fluorescence staining method. The developmental rate beyond morula stages in NCSU 23 containing NAC(1nm) or NAC(1nm) plus EGF(100ng/$m\ell$) or PDGF(5ng/$m\ell$) were 28.1, 32.3 and 35.3%, respectively. NAC plus PDGF group was slightly higher than control group(P>0.05). The developmental capacity in NCSU 23 containing ebselen(10 $\mu$M) or ebselen(10 $\mu$M) plus EGF(100ng/$m\ell$) or PDGF(5ng/$m\ell$) were 17.8, 36.9 and 40.3%, respectively Ebselen plus growth factor groups were significantly higher than control group(P<0.05). The developmental capacity in NCSU 23 containing glutathione(100 $\mu$M) or glutathione(100 $\mu$M) plus EGF (100ng/$m\ell$) or PDGF(5ng/$m\ell$) were 24.1, 30.5 and 27.7%, respectively. There were not difference in all experimental groups(P>0.05). In all experimental groups, there was no significantly differences on the cell number of blastocysts, but ebselen plus growth factor groups were significantly higher than control group. These studies indicate that antioxidants plus growth factors can increase the proportion of embryos that developed beyond morulae stage.

• Tuberculosis and Respiratory Diseases
• /
• v.49 no.4
• /
• pp.495-501
• /
• 2000

Background : Cardiopulmonary exercise test is a useful test for the evaluation of the cardiovascular and respiratory systems. Obese subjects have an increased resting metabolic rate ($VO_2$) compared to non~obese subjects and the increase is more marked during dynamic exercise, which results in the limitation of maximal exercise in obese subjects. In this study, the influence of the obesity and fat distribution on the maximal exercise capacity were evaluated. Methods : Maximal exercise capacity was represented by maximam maximum oxygen uptake and $VO_2$ max in the cardiopulmonary test. Obesity, total fat content and abdomina1 obesity(waist to hip ratio, WHR) were measured by bioelectrical impedence method. Total of 42 volunteers (male 22, fema1e 20) were evaluated. Results : 1) Weight to height ratio (mean$\pm$SD) was 110$\pm$14.9% in men and 100$\pm$11.1% in women. 2) Fat ratio (mean$\pm$SD) was 23.3$\pm$5.2% in men and 27.55$\pm$3.9% in woman. 3) Waist to hip ratio (mean$\pm$SD) was 0.85$\pm$0.04 in men and 0.8$\pm$0.03 in woman. 4) In men, $VO_2$ max/min/Kg was negatively correlated with obesity, fat ratio, and abdominal fat distribution. 5) In woman, $VO_2$ max/Kg was negatively correlated with obesity and fat ratio, but did not show significant relationship with abdominal fat distribution. Conclusion : Obesity was a limiting factor for maximal exercise in both men and women. Abdominal obesity was a limiting factor for maximal exercise in men but its implication to women needs further evaluation.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.4
• /
• pp.239-244
• /
• 2007

In order to investigate the effect of fluorine ion in the $Li_{1-x}FeO_2Li_xMnO_2$ (Mn/(Mn + Fe) = 0.8) cathode material, it was synthesized $Li_{1-x}FeO_{2-y}F_y-Li_xMnO_2$ (Mn/(Mn + Fe) = 0.8, $0.05{\le}y{\le}0.15$) cathode materials at $350^{\circ}C$ for 10hrs using solid-state method. $Li_{1-x}FeO_{2-y}F_y-Li_xMnO_2$ (Mn/(Mn + Fe) = 0.8, $0.0{\le}y{\le}0.1$ was composed many large needle-like particles of about $1-1.5\;{\mu}m$ and small particles of about 50-100 nm, which were distributed among the larger particles. However, $Li_{1-x}FeO_{1.85}F_{0.15}-Li_xMnO_2$ material showed slightly different particle morphology. The particles of $Li_{1-x}FeO_{1.85}F_{0.15}-Li_xMnO_2$ were suddenly increased and started to be a spherical type of particle shape. $Li/Li_{1-x}FeO_{1.9}F_{0.1}-Li_xMnO_2$ cell showed a high initial discharge capacity of 163 mAh/g and a high cycle retention rate of 95% after 50 cycles. The initial discharge capacity of $Li/Li_{1-x}FeO_{2-y}F_y-Li_xMnO_2$ ($0.05{\le}y{\le}0.15$) cells increased according to the increase of F content. However, the cycleability of this cell was very rapidly decreased when the substituted fluorine content is over 0.1. We suggested that too large amount of F ion fail to substitute into the $Li_{1-x}FeO_2-Li_xMnO_2$ structure, which resulted in the severe decline of battery performance.