• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.385-390
• /
• 2001

This paper presents a nonlinear analysis technique with slip, the effects of slip modulus and composite action by shear connector on behavior and capacity in composite structure of sandwich system. As a results of this study, it proved that the slip modulus, in case of shear behavior, seldom influence load-resistance capacity such as yield and ultimate load, but in case of flexural behavior, it appropriately influence load-resistance capacity because of stress redistribution by slip. In case of flexural behavior, analysis result for perfect-composite results in over-estimation and perfect-slip results in under-estimation on behavior and capacity. Therefore, it is desirable to model steel-concrete interface with partial-composite. The effects of slip on behavior and capacity are less in case of positive composite than loosely composite, and it proved that composite action by shear connector improve the load-resistance capacity of this system.

• Proceedings of the KSR Conference
• /
• 2003.10b
• /
• pp.326-333
• /
• 2003

Railway system is consisted of resources such as rail-line, signalling system, and railcars. It is necessary to efficiently utilize these limited and expensive resources as much as possible up to given line capacity. So far, we treat the line capacity as the criteria for evaluating investment alternatives or for restricting train frequencies, and this criteria is calculated statical and experimental numerical formula. But, line capacity has special attribute that changes dynamically according to operational conditions, so there is a need of new line capacity estimation system. In this paper, we present systematic line capacity analysis model. The proposed model has three main components; TPS(tain performance simulator), PES(parameter evaluation simulator), LCS(line capacity simulator).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.4
• /
• pp.2428-2435
• /
• 2014

Numerical analysis with ALE (Arbitrary Lagrangian Eulerian) Adaptive Meshing technique was performed to evaluate the pullout capacity of the embedded suction anchors (ESA) in uniform clay. The numerical method was verified by the previous study, analytical results based on limit-equilibrium theory and centrifuge tests. The pullout capacity of the ESA under horizontal, vertical, and inclined loading were evaluated, and the effect of initial rotation of the ESA on pullout capacity was also investigated. The analysis results showed that the maximum horizontal capacity was obtained at the mid-point, and the each vertical capacity gave the similar value regardless of the loading points. Furthermore, the inclined capacity was decreased as the load inclination angle increased at the mid-point of the anchor, and almost the same pullout capacity was obtained when the initial rotation angles were below 30 degrees.

• Environmental and Resource Economics Review
• /
• v.15 no.1
• /
• pp.71-94
• /
• 2006

Reducing fishing capacity is one of hot issues in the world fisheries. Increased fishing capacity causes not only fish stocks to be depleted, but also additional fishing costs to be incurred, resulting in reductions of fishing profits. In order to achieve a sustainable and profitable development of fisheries, it is inevitable to reduce fishing capacity. For this reason, FAO adopted 'the International Plan of Action for the Management of Fishing Capacity' and recommended member countries to estimate fishing capacity and to implement the policy to reduce fishing capacity. This study is aimed at measuring fishing capacity of Large Purse Seines Fishery using a Data Envelopment Analysis (DEA). The DEA result showed that the practical catch of large purse seine fishery in 2003 was 158,662 tons, but the capacity output for current input was 318,397 tons. The capacity utilization is about 50%, it is obvious the capacity did not utilize enough. The sensitivity analysis on DEA results indicated that the number of ships (including tonnage and horse power) should be scrapped by 50% or days fished should be reduced by 63% if the present catch remained. In addition, if the catch remains at the MSY base level of large purse seines, the analysis suggested that the number of ships (including tonnage and horse power) should be reduced by 30%, otherwise days fished should be reduced by 60%.

• Structural Engineering and Mechanics
• /
• v.63 no.2
• /
• pp.195-206
• /
• 2017

This paper presents the parametric numerical analysis on the ultimate bearing capacity of the purlin-sheet roofs connected by standing seam clips. The effects of several factors on failure modes and ultimate bearing capacity of the purlins are studied, including setup of anti-sag bar, purlin type, sheet thickness and connection type et al. A simplified design formula is proposed for predicting the ultimate bearing capacity of purlins. Results show that setting the anti-sag bars can improve the ultimate bearing capacity and change the failure modes of C purlins significantly. The failure modes and ultimate bearing capacity of C purlins are significantly different from those of Z purlins, in the purlin-sheet roof connected by standing seam clips. Setting the anti-sag bars near the lower flange is more favorable for increasing the ultimate bearing capacity of purlins. The ultimate bearing capacity of C purlins increases slightly with sheet thickness increasing from 0.6 mm to 0.8 mm. The ultimate bearing capacity of the purlin-sheet roofs connected by standing seam clips is always higher than those by self-drilling screws. The predictions of the proposed design formulas are relatively in good agreement with those of EN 1993-1-3: 2006, compared with GB 50018-2002.

• Wind and Structures
• /
• v.13 no.1
• /
• pp.1-20
• /
• 2010

The recommended factored design wind load effects for overhead lattice transmission line towers by codes and standards are evaluated based on the applicable wind load factor, gust response factor and design wind speed. The current factors and design wind speed were developed considering linear elastic responses and selected notional target safety levels. However, information on the nonlinear inelastic responses of such towers under extreme dynamic wind loading, and on the structural capacity curves of the towers in relation to the design capacities, is lacking. The knowledge and assessment of the capacity curve, and its relation to the design strength, is important to evaluate the integrity and reliability of these towers. Such an assessment was performed in the present study, using a nonlinear static pushover (NSP) analysis and incremental dynamic analysis (IDA), both of which are commonly used in earthquake engineering. For the IDA, temporal and spatially varying wind speeds are simulated based on power spectral density and coherence functions. Numerical results show that the structural capacity curves of the tower determined from the NSP analysis depend on the load pattern, and that the curves determined from the nonlinear static pushover analysis are similar to those obtained from IDA.

• Geomechanics and Engineering
• /
• v.13 no.4
• /
• pp.701-714
• /
• 2017

The effect of nearby cohesionless sloping ground on the uplift capacity of horizontal strip plate anchor embedded in sand deposit with horizontal ground surface has been studied numerically. The numerical analysis has been carried out by using the lower bound theorem of limit analysis with finite elements and linear optimization. The results have been presented in the form of non-dimensional uplift capacity factor of anchor plate by changing its distance from the slope crest for different slope angles, embedment ratios and angles of soil internal friction. It has been found that the decrease in horizontal distance between the edge of the anchor plate and the slope crest causes a continuous decrease in uplift capacity of anchor plate. The optimum distance is that distance between slope crest and anchor plate below which uplift capacity of an anchor plate has been found to decrease with a decrease in normalized crest distance from the anchor plate in presence of nearby sloping ground. The normalized optimum distance between the slope crest and the anchor plate has been found to increase with an increase in slope angle, embedment ratio and soil internal friction angle.

• Structural Engineering and Mechanics
• /
• v.68 no.6
• /
• pp.647-660
• /
• 2018

The Incremental Dynamic Analysis (IDA) procedure is currently known as a robust tool for estimation of seismic collapse capacity. However, the procedure is time-consuming and requires significant computational efforts. Recently some simplified methods have been developed for rapid estimation of seismic collapse capacity using pushover analysis. However, a comparative review and assessment of these methods is necessary to point out their relative advantages and shortcomings, and to pave the way for their practical use. In this paper, four simplified pushover analysis-based methods are selected and applied on four regular RC intermediate moment-resisting frames with 3, 6, 9 and 12 stories. The accuracy and performance of the different simplified methods in estimating the median seismic collapse capacity are evaluated through comparisons with the results obtained from IDAs. The results show that reliable estimations of the summarized 50% fractile IDA curve are produced using SPO2IDA and MPA-based IDA methods; however, the accuracy of the results for 16% and 84% fractiles is relatively low. The method proposed by Shafei et al. appears to be the most simple and straightforward method which gives rise to good estimates of the median sidesway collapse capacity with minimum computational efforts.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 1997.11a
• /
• pp.145-150
• /
• 1997

In this thesis, the field test by truck load and the structural analysis were performed on a preflex beam bridge to investigate the load carrying capacity. From the field test and the structural analysis results, K(corrective factor) and $P_n$(load carrying capacity) of the preflex beam bridges were studied, and these factors were applied to the load carrying capacity assessment of the preflex bridges.

• Journal of the Korean Society of Safety
• /
• v.13 no.3
• /
• pp.126-134
• /
• 1998

In this paper, the field test by truck load and the structural analysis were performed on a prestressed concrete beam bridge to investigate the load carrying capacity of the prestressed concrete beam bridges. From the results of the field test and the structural analysis, CAF (composite action factor), TIF(transformed impact factor), and $P_n$(load carrying capacity) of the prestressed concrete beam bridges were studied, and the load carrying capacity assessment of the prestressed concrete beam bridges were carried out using these factors.