• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.3
• /
• pp.198-206
• /
• 2013

This paper presents a wide band, fine-resolution digitally controlled oscillator (DCO) with an on-chip 3-D solenoid inductor using the 0.13 ${\mu}m$ digital CMOS process. The on-chip solenoid inductor is vertically constructed by using Metal and Via layers with a horizontal scalability. Compared to a spiral inductor, it has the advantage of occupying a small area and this is due to its 3-D structure. To control the frequency of the DCO, active capacitor and active inductor are tuned digitally. To cover the wide tuning range, a three-step coarse tuning scheme is used. In addition, the DCO gain needs to be calibrated digitally to compensate for gain variations. The DCO with solenoid inductor is fabricated in 0.13 ${\mu}m$ process and the die area of the solenoid inductor is 0.013 $mm^2$. The DCO tuning range is about 54 % at 4.1 GHz, and the power consumption is 6.6 mW from a 1.2 V supply voltage. An effective frequency resolution is 0.14 kHz. The measured phase noise of the DCO output at 5.195 GHz is -110.61 dBc/Hz at 1 MHz offset.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.3
• /
• pp.205-212
• /
• 2002

The growth characteristics of metal-organic chemical vapor deposition (MOCVD) $Pb(Zr_xTi_{1-x})O_3 (PZT) thin films were investigated for the application of high-density ferroelectric random access memories (FRAM) devices beyond 64Mbit density. The supply control of Pb precursor plays the most critical role in order to achieve a reliable process for PZT thin film deposition. We have monitored the changes in the microstructure and electrical properties of films on increasing the Pb precursor supply into the reaction chamber. Under optimized conditions, $Ir/IrO_2/PZT(100nm)/Ir capacitor shows well-saturated hysteresis loops with a remanent polarization (Pr) of $~28{\mu}C/textrm{cm}^2$ and coercive voltage of 0.8V at 2.5V. Other issues such as step coverage, compositional uniformity and low temperature deposition was discussed in viewpoint of actual device application.

• Journal of the Korean Society of Safety
• /
• v.26 no.6
• /
• pp.13-19
• /
• 2011

The purpose of this study is to examine the cause of damage to electrolytic capacitors and to present the heat generation mechanism in order to prevent the occurrence of similar problems. From the analysis results of electrolytic capacitors collected from accident sites, the fire causing area can be limited to the primary power supply for the initial accident. From the tests performed by applying overvoltage, surge, etc., it is thought that the fuse, varistor, etc., are not directly related to the accidents that occurred. The analysis of the characteristics using a switching regulator showed that the charge and discharge characteristics fell short of standard values. In addition, it is thought that heated electrolytic capacitors caused thermal stress to nearby resistances, elements, etc. It can be seen that the heat generation is governed by the over-ripple current, application of AC overvoltage, surge input, internal temperature increase, defective airtightness, etc. Therefore, when designing an electrolytic capacitor, it is necessary to comprehensively consider the correct polarity arrangement, appropriate voltage application, correct connection of equivalent series resistance(ESR) and equivalent series inductance(SEL), rapid charge and discharge control, sufficient margin of dielectric tangent, etc.

• Electrical & Electronic Materials
• /
• v.8 no.5
• /
• pp.640-647
• /
• 1995

In this study, the BaTiO$\sub$3/ capacitor add to MnO$\sub$2/ like depressor and shifter were investigated for temperature or voltage compensation by structural and electrical analysis. The relative density of BCTM, generating poly crystall and formation of lattice defect, has a 90[%] over as the CaTiO$\sub$3/ come out to control grain size. The current density of BCTM2 increased non-ohmic in high-electric field but that BCTM3 and BCTM4 had a few changing. The BCTM3 and BCTM4 unformated grain boundary shown temperature compensation properties, so that the dielectric constant was low value. The curie point was near 140[.deg. C] in BCTM1 and BCTM4, but BCTM3 and BCTM4 not shown the curie point. It is found that the charging energy of BCTM4 was changed 6[%] according to rising temperature from room temperature to 417[K]. The formation of BaMnO$\sub$3/ was low dielectric constant to change frequency and temperature.

• Journal of Sensor Science and Technology
• /
• v.31 no.2
• /
• pp.115-119
• /
• 2022

A readout circuit for a mercury-cadmium-telluride (MCT)-amplified mid-wave infrared (IR) photodetector was realized and applied to noncontact chemical agent detectors based on a quantum cascade laser (QCL). The QCL emitted 250 times for each wavelength in 0.2-㎛ steps from 8 to 12 ㎛ with a frequency of 100 kHz and duty ratio of 10%. Because of the nonconstant QCL emission power during on-duty, averaging the photodetector signals is essential. Averaging can be performed in digital back-end processing through a high-speed analog-to-digital converter (ADC) or in analog front-end processing through an integrator circuit. In addition, it should be considered that the 250 IR data points should be completely transferred to a PC during each wavelength tuning period of the QCL. To average and minimize the IR data, we designed a readout circuit using the analog front-end processing method. The proposed readout circuit consisted of a switched-capacitor integrator, voltage level shifter, relatively low-speed analog-to-digital converter, and micro-control unit. We confirmed that the MCT photodetector signal according to the QCL source can be accurately read and transferred to the PC without omissions.

• Journal of Power Electronics
• /
• v.15 no.5
• /
• pp.1348-1357
• /
• 2015

Under traditional unified power quality conditioner (UPQC) control, a UPQC series converter (SC) is mainly used to handle grid-side power quality problems while its parallel converter (PC) is mainly used to handle load-side power quality problems. The SC and PC are relatively independent. The SC is usually in standby mode and it only runs when the grid voltage abruptly changes. In this paper, novel UPQC coordinated control strategies are proposed which use the SC to share the reactive power compensation function of the PC especially without grid-side power quality problems. However, in some cases, there will be a circulating current between the SC and the PC, which will probably influence the compensation fashion, the compensation capacity, or the normal work of the UPQC. Through an active power circulation analysis, strategies with and without a circulating current are presented which fuses the reactive power allocation strategy of the SC and the PC, the composite control strategy of the SC and the compensation strategy of the DC storage unit. Both of the strategies effectively solve the SC long term idle problem, limit the influence of the circulating current, optimize all of the UPQC units and reduce the production cost. An analysis, along with simulation andexperimental results, is presented to verify the feasibility and effectiveness of the proposed control strategies.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.7
• /
• pp.513-518
• /
• 2016

The piezoelectric actuating device is known for its large power density and simple structure. It can generate a larger force than a conventional actuator and has also wide bandwidth with fast response in a compact size. To control the piezoelectric actuator, we need an analog signal conditioning circuit as well as digital microcontrollers. Conventional microcontrollers are not equipped with an analog part and need digital-to-analog converters, which makes the system bulky compared with the small size of piezoelectric devices. To overcome these weaknesses, we are developing a single-chip controller that can handle analog and digital signals simultaneously using mixed-signal FPGA technology. This gives more flexibility than traditional fixed-function microcontrollers, and the control speed can be increased greatly due to the parallel processing characteristics of the FPGA. In this paper, we developed a floating-point multiplier, PWM generator, 80-kHz power control loop, and 1-kHz position feedback control loop using a single mixed-signal FPGA. It takes only 50 ns for single floating-point multiplication. The PWM generator gives two outputs to control the charging and discharging of the high-voltage output capacitor. Through experimentation and simulation, it is demonstrated that the designed control loops work properly in a real environment.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.531-533
• /
• 1996

The most common method of the single phase induction motor(SPIM) is to install a starting condenser and a centrifugal switch in series with the auxiliary winding. Even though this capacitor start method is embodied simply, it is feasible because of motor failure from malfunction of the centrifugal switch and the starting condenser. Moreover, it is hard to improve the performance characteristics of the SPIM. In this paper, the voltage and phase angle sequence, control strategy of the auxiliary winding of the SFIM is employed to eliminate the centrifugal switch and the starting condenser. The proposed control system is superior to a conventional system in the starting performance of SPIM. Finally, the improved starting characteristics of the SPIM is obtained with this strategy through simulation and experimental results.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.400-402
• /
• 1994

This paper presents a digital implementation of delta modulation Technique for Active Power Filters. Delta modulated scheme is to control the harmonic-compensating current indirectly by adjusting the capacitor voltage to be sinusoidal. The overall control system has two feedback loops. One is the outer propotional feedback for loop regulating the dc current of active filters and the other is the inner feedback loop for maintaining the ac current waveform to be sinusoidal, and have zero power factor angle(i.e. unity power factor). The characteristics of the proposed is investigated by digital simulation using ACSL and experimental results are obtained by TMS370C756 Single-Chip Microprocessor relative to analog delta modulation technique.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.429-431
• /
• 1994

A parallel resonant dc link inverter, one of the many resonant inverters, has some superior characteristics in camparision with other resonant inverters. But loss of the resonant oscillation and occurrence of high peak voltage in the resonant capacitor of these inverters are serious problems. In this paper, we investigate a control method for resonant dc link inverters which can overcome these problems. Experimental results are presented to show superior operation of the resonant dc link inverter using the proposed control method.