• Progress in Superconductivity
• /
• 제14권1호
• /
• pp.1-10
• /
• 2012

We fabricated a closed coils by using resistive-joint method and the joint resistance of the coils were estimated by field decay technique in liquid nitrogen. We used the Runge-kutta method for the numerical analysis to calculate the decay properties. The closed coil was wound by $(Bi,Pb)_2Sr_2Ca_2Cu_3O_x$/Ag tape. Both ends the tape were overlapped and soldered to each other. The current was induced in a closed coils by external magnetic flux density. Its decay characteristic was observed by means of measuring the magnetic flux density generated by induced current at the center of the closed coil with hall sensor. The joint resistance was calculated as the ratio of the inductance of the loop to the time constants. The joint resistances were evaluated as a function of critical current of loop, contact length, sweep time, and external magnetic flux density in a contact length of 7 cm. It was observed that joint resistance was dependent on contact length of a closed coil, but independent of critical current, sweep time, and external magnetic flux density. The joint resistance was measured to be higher for a standard four-probe method, compared with that for the field decay technique. This implies that noise of measurement in a standard four-probe method is larger than that of field decay technique. It was estimated that joint resistance was $8.0{\times}10^{-9}{\Omega}$ to $11.4{\times}10^{-9}{\Omega}$ for coils of contact length for 7 cm. It was found that 40Pb/60Sn solder are unsuitable for persistent mode.

• 한국전기전자재료학회논문지
• /
• 제21권9호
• /
• pp.835-843
• /
• 2008

We have fabricated the source-drain electrodes for OTFTs by screen printing method and manufactured Ag pastes as conductive paste. To obtain excellent conductivity and screen-printability of Ag pastes, the dispersion characteristics of Ag pastes prepared from two types of acryl resins with different molecular structures and Ag powder treated with caprylic acid, triethanol amine and dodecane thiol as surfactant respectively were investigated. The Ag pastes containing Ag powder treated with dodecane thiol having thiol as anchor group or AA4123 with carboxyl group(COOH) of hydrophilic group as binder resin exhibited excellent dispersity. But, Ag pastes(CA-41, TA-41, DT-41) prepared from AA4123 fabricated the insulating layer since the strong interaction between surface of Ag powder and carboxyl group(COOH) of AA4123 interfered with the formation of conduction path among Ag powders. The viscosity behavior of Ag pastes exhibited shear-thinning flow in the high shear rate range and the pastes with bad dispersion characteristic demonstrated higher shear-thinning index than those with good dispersity due to the weak flocculated network structure. The output curve of OTFT device with a channel length of 107 ${\mu}m$ using screen-printed S-D electrodes from DT-30 showed good saturation behavior and no significant contact resistance. And this device exhibited a saturation mobility of $4.0{\times}10^{-3}$ $cm^2/Vs$, on/off current ratio of about $10^5$ and a threshold voltage of about 0.7 V.

• 한국전기전자재료학회논문지
• /
• 제26권12호
• /
• pp.858-862
• /
• 2013

The front electrode should be used to make solar cell panel so as to collect electron. The front electrode is used by paste type, printed on the Si-solar cell wafer and sintered at about $800^{\circ}C$. The paste is composed Ag powder and glass frit which make the ohmic contact between Ag electrode and n-type semiconductor layer. From the previous study, the Ag electrodes which used two commercial glass frit of Bi-system were so different on the interface resistance. The main composition of them was Bi-Zn-B-Si-O and few additives added in one of them. In this study, glass frit was made with the ratio of $Bi_2O_3$ and ZnO on the main composition, and then paste using glass frit was prepared respectively. And, also, the paste using the glass frit added oxide additives were prepared. The change of interface resistance was not large with the ratio of $Bi_2O_3$ and ZnO. In the case of G6 glass frit, 78 wt% $Bi_2O_3$ addition, the interface resistance was $190{\Omega}$ and most low. In the glass frit added oxide, the case of Ca increased over 10 times than it of G6 glass frit on the interface resistance. It was thaught that after sintering, Ca added glass frit was not flowed to the interface between Ag electrode and wafer but was in the Ag electrode.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.219-219
• /
• 2012

The formation and thermal desorption behaviors of octanethiol (OT) SAMs on single crystalline Au (111) and polycrystalline Au, Ag, and Cu substrates were examined by X-ray photoelectron microscopy (XPS), thermal desorption spectroscopy (TDS), and contact angle (CA) measurements. XPS and CA measurements revealed that the adsorption of octanethiol (OT) molecules on these metals led to the formation of chemisorbed self-assembled monolayers (SAMs). Three main desorption fragments for dioctyl disulfide (C8SSC8+, dimer), octanethiolate (C8S+), and octanethiol (C8SH+) were monitored using TDS to understand the effects of surface morphology and the nature of metal substrates on the thermal desorption behavior of alkanethiols. TDS measurements showed that a sharp dimer peak with a very strong intensity on single crystalline Au (111) surface was dominantly observed at 370 K, whereas a broad peak on the polycrystalline Au surface was observed at 405 K. On the other hand, desorption behaviors of octanethiolates and octanethiols were quite similar. We concluded that substrate morphology strongly affects the dimerization process of alkanethiolates on Au surfaces. We also found that desorption intensity of the dimer is in the order of Au＞＞Ag＞Cu, suggesting that the dimerization process occurs efficiently when the sulfur-metal bond has a more covalent character (Au) rather than an ionic character (Ag and Cu).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.349-352
• /
• 1998

In future superconducting electrical machines and device. AC loss in the superconducting windings are one of the most impotent design paramenters. This paper descriptions a series of Characteristic of a high-Tc superconducting Bi-Pb-Sr-Ca-Cu-O Ag-sheathed filament. In the case simulation and design to reduce ac loss is considered the filament number, twitch pith number and diameter of filament. A filament sample with Tc of 78K is made by $835^{\circ}C$ sintering for 50h and $0.33^{\circ}C$/min heating rate in an atmosphere. The experiment observations are compared with self-field loss and AC losses of Bi-Pb-Sr-Ca-Cu-O filament at 77K in following environments ; (i)AC external parallel magnetic field in different frequencies. And an analytical expression of the loss the derivation of transposition from an optimum condition was derived for the external AC magnetic field, theoretical predictions were found to coincide with the experimental observations.

• 한국해양학회지
• /
• 제22권3호
• /
• pp.130-142
• /
• 1987

제주남방해역 표층퇴적물에 대해 입도분석, 경광물 및 점토광물, 그리고 미량원소 분석을 실시하였다. 본 연구해역의 퇴적물상은 남동부의 오조립질 분포역 과 남서부 조`세립질 분포지로 구분되며, 남서쪽 끝지역에는 소규모의 현생니질퇴적 물 분포대(mud zone)도 존재한다. 본 역에 분포하는 퇴적물은 분급이 불량하고 negative~positive skewed할뿐 아니라 platykurtic~leptokurtic한 특성을 나타냈으며, 조립질은 도약(saltation)에 의해, 세립질은 도약 및 부유(suspension)에 의해 운반된 것으로 보여 진다. 측정된 13종의 지화학적원소성분중 Co, Ni, Ca, Ag를 제외한 9 종은 남동부지역에서 남서부지역으로 향함에 따라 함량이 증가하는 경향을 보였고, Co와 Ni은 동`서부간에 유사한 함량분포를 나타냈으나 Ca와 Ag은 남동부지역에서 함량치가 높았다. 탄산염함량은 남동부의 조립질 분포역에서가 남서부보다 높게나 타난 반면 총 유기물함량은 이와는 상반된 경향을 보였다. 경광물은 석영, 암편, K- 장석, Na-Ca장석 순의 조성을 보였는데 제주도 주변 해역에서 외해쪽으로 향함에 따라 석영과 K-장석의 함량증가하고 Na-Ca장석과 암편은 감소하는 경향을 나타냈 다. 조사지역 남서쪽 끝 mud 지역의 점토광물로는 illite, chlorite, kaolinite, feldspar, calcite등인데, chlorite가 양적으로 많고 calcite peak가 현저하게 나타날 뿐만 아니라 Ca, Pb, Ni등의 지화학적원소성분의 함량도 황하기원퇴적물의 특성치 와 유사하여 이 지역세립질퇴적물 대부분은 황하기원인 것으로 사료된다.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제5C권5호
• /
• pp.204-210
• /
• 2005

Alternating current (AC) losses of two Bi-2223 ([Bi, Pb]: Sr: Ca: Cu: O = 2:2:2:3) tapes [(Tape I, un-twist-pitch) and the other with a twist-pitch of 10 mm (Tape II)] were measured and compared. These samples, produced by the powder-in-(Ag) tube (PIT) method, are multi-filamentary. Also, it's produced by non-twist and different twist pitch (8, 10, 13, 30, 50 and 70 mm). The critical current measurement was carried out under the environment in liquid Nitrogen and in zero-field by 4-probe method. Susceptibility measurements were conducted while cooling in a magnetic field. Flux loss measurements were conducted as a function of ramping rate, frequency and field direction. The AC flux loss increases as the twist-pitch of the tapes decreased, in agreement with the Norris Equation. Neutron-diffraction measurements have been carried out investigate the crystal structure, magnetic structures, and magnetic phase transitions in Bi-2223([Bi, Pb]:Sr:Ca:Cu:O)

• Bulletin of the Korean Chemical Society
• /
• 제15권11호
• /
• pp.940-944
• /
• 1994

The crystal structure of an ethylene sorption complex of dehydrated $Ag_{12}-A $reacted with bromine vapor has determined by single-crystal X-ray diffraction techniques in the cubic space group of Pm3m at 22(l)$^{\circ}$C (a=12.180(2) ${\AA}$). The crystal was prepared by dehydration of $Ag_{12}$-A at 400 $^{\circ}$C and $2 {\times} l0^{-6}$ Torr for 2 days, followed by exposure to 200 Torr of ethylene gas at 24(l) $^{\circ}$C for 1 hr. After the ethylene gas was evacuated for 1 hr, the crystal was exposed to 180 Torr of bromine vapor at 24(l) $^{\circ}$C for 1.5 h. The structure was refined to the final error indices, $R_1=0.066\;and\;R_2$ (weighted)=0.055, using 137 independent reflections for which I>3${\sigma}$I. About 55% of the sodalite unit contain two 6-ring $Ag^+$ ions and the remaining 45% contain $Ag_6$ molecules complexed to 2 $Ag^+$ ions at 6-ring sites to give $(Ag^+)_2(Ag_6).$ Upon sorption of ethylene, 4.75 ethylene molecules were sorbed per unit cell and of these, only 1.25 ethylene molecules were brominated by treatment of dibromine because of the limitation of the available space for the reaction products in the large cavity. In the large cavity, each of 3.5 $Ag^+$ ions forms a lateral ${\pi}$ complex with an ethylene molecule. About 2.5 8-ring $Ag^+$ ions per unit cell interact with 1.25 1,2-dibromoethane and each of ca. 1.25 6-ring $Ag^+$ ions also interacts with one of bromine atoms of 1,2-dibromoethane. Each bromine atom approaches a carbon atom with C-Br(l)=2.07(20) ${\AA}$ and C-Br(2)=2.07(10) ${\AA}$, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 초전도 자성체
• /
• pp.55-58
• /
• 2002

PIT method which is used at fabricating Bi-2223/Ag HTS wire includes a drawing process, conventional deformation method. Drawing of meta1(Ag) and ceramic (BiSrCaCuO) composite is also difficult and significant for uniform deformation. In this paper, parameters of uniform deformation was studied at Bi-2223/ Ag multifilamentary HTS wire. Powder and rod as a starting precursor was compared at 55 filament and 54 filament Bi-2223/Ag HTS wire, respectively. Micro-hardness and area COV of the filaments was also evaluated when the diameters were decreased through drawing operations.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.234-235
• /
• 2007

We have fabricated superconductor ceramics by chemical process. A high Tc superconductorwith a nominal composition of $Bi_{2}Sr_{2}Ca_{2}Cu_{3}O_y$ was prepared by the organic metal salts method. Experimental results suggest that the intermediate phase formed before the formation of the superconductor phase may be the most important factor. During the sintering, doped $Ag_{2}O$ was converted to Ag particles which were finely dispersed in superconductor samples.