• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.3
• /
• pp.265-271
• /
• 2008

TCP(Tape Carrier Package), COG (Chip On Glass), COF(Chip On Film) are three methods for connecting LDI(LCD Driver IC) with LCD panels. Especially COF is growing its portion of market place because of low cost and fine pitch correspondence. But COF has a problem of the lead broken failure in LCD module process and the usage of customer. During PCB (Printed Circuit Board) bonding process, the mismatch of the coefficient of thermal expansion between PCB and D-IC makes stress-concentration in COF lead, and also D-IC bending process during module assembly process makes the level of stress in COF lead higher. As an affecting factors of lead-broken failure, the effects of SR(Solder Resister) coating on the COF lead, surface roughness and grain size of COF lead, PI(Polyimide) film thickness, lead width and the ACF(Anisotropic Conductive Film) overlap were studied, The optimization of these affecting manufacturing processes and materials were suggested and verified to prevent the lead-broken failure.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.09a
• /
• pp.21-30
• /
• 2002

According the difference of flex substrate, (reel tape), there are three kind assembly types of LCD driver IC is COG, TCP and COF, respectively. The TCP is the maturest in these types for stability of raw material supply and other specification. And TCP is the major assembly type of LCD driver IC and the huge demand from Taiwan's large TFT LCD panel house since this spring. But due to its package structure and the raw material applied in this package, there is some limitation in fine pitch application of this package type, (TCP). So, COF will be very potential in compact and portable application comparison with TCP in the future. There are three kinds assembly methods in COF, one is ACF by using the anisotropic conductive film to connect the copper lead of tape and gold bump of IC, another is eutectic bonding by using the thermo-pressure to joint the copper lead of tape and gold bump of IC, and last is NCP by using non-conductive paste to adhere the copper lead of tape and gold bump of IC. To have a global realization, this paper will briefly review the status of Taiwan's large TFT panel house, the internal driver IC design house, and the back-end assembly house in the beginning. The different material property of raw material, PI tape is also compared in the paper. The more detail of three kinds of COF assembly method will be described and compared in this paper.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.2
• /
• pp.313-318
• /
• 2012

This paper presents an automatic system to detect variety of faults from fine pitch COF(chip-on-film) which is less than $30{\mu}m$. Developed system contains circuits and technique to detect fast various faults such as hard open, hard short, soft open and soft short from fine pattern. Basic principle for fault detection is to monitor fine differential voltage from pattern resistance differences between fault-free and faulty cases. The technique uses also radio frequency resonator arrays for easy detection to amplify fine differential voltage. We anticipate that proposed system is to be an alternative for conventional COF test systems since it can fast and accurately detect variety of faults from fine pattern COF test process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.45-46
• /
• 2011

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.2
• /
• pp.7-15
• /
• 2008

In this paper, the Chip-On-Flex (COF) assembly process using anisotropic conductive films (ACFs) was investigated and the reliability of COF assemblies using ACFs was evaluated. Thermo-mechanical properties of ACFs such as coefficient of thermal expansion (CTE), storage modulus (E'), and glass transition temperature $(T_g)$ were measured to investigate the effects of ACF material properties on the reliability of COF assemblies using ACFs. In addition, the bonding conditions for COF assemblies using ACFs such as time, temperature, and pressure were optimized. After the COF assemblies using ACFs were fabricated with optimized bonding conditions, reliability tests were then carried out. According to the reliability test results, COF assemblies using the ACF which had lower CTE and higher $T_g$ showed better thermal cycling reliability. Consequently, thermo-mechanical properties of ACFs, especially $T_g$, should be improved for high thermal cycling reliability of COF assemblies using ACFs for compact camera module (CCM) applications.

• Journal of the Semiconductor & Display Technology
• /
• v.3 no.3
• /
• pp.11-17
• /
• 2004

This research has been progressed for adhesive improvement of the Polyimide/Buffer layer/Cu at the COF(Chip On Film) which induced as the alternative plan about high concentration of a circuit or substrates according to demands of miniaturization and high efficiency of various electronic equipment. RF plasma equipment was applied to when plama pretreatment was performed for improvement of adhesive strength of PI and Cr as the buffer layer. Experimental fluents were a species of the buffer layer, depositied time and the ratio of $O_2$/Ar when performed to plasma pretreatment. The results are that Ni was superior to Cr at peel test according to a species of the buffer layer, peel strength and Cu THK were showed proportional relation to deposition structure of the same buffer layer and sample of the Cr depositied time(30 sec) and Cu depositied time(20 min) was showed good adhesion to peel test according to Cr's depositied time and Cu's depositied time. When perform PI's plasma pretreatment peel strength and $O_2$/Ar ratio were showed proportional relation. But $O_2$/Ar(2/5) was best condition since then decreased.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.775-778
• /
• 2010

본 논문에서는 초미세 패턴($24{\mu}m$ 이하의 선폭, $30{\mu}m$ 이하의 피치)을 가진 칩-온-필름(Chip-on-Film, COF)에 발생한 결함을 자동으로 검출할 수 있는 시스템을 제안한다. 개발된 시스템은 COF 패턴으로부터 대표적으로 발생하는 결함들, 즉 개방(open), 단락(hard short), mouse bite(near open) 및 near short(soft short)을 자동으로 신속히 검출할 수 있는 기술이 적용되어 있다. 특히 초미세 패턴의 경우, near open 및 near short과 같은 결함 검출이 불가능한 기존 검출시스템의 문제점을 극복한 기술이 제안되어 있다. 본 논문에서 제안하는 결함 검출 원리는 미세 선의 결함유무에 따른 저항 변화를 자동으로 검출하고, 그 미세한 변화를 좀 더 자세하게 판별하기 위해 고주파 공진기(resonator)를 적용하고 있다. 제안된 시스템은 미세 패턴을 가진 COF 제작 과정에서 발생한 결함을 신속히 검출할 수 있기 때문에 COF 불량 검사에 소요되는 많은 경비를 줄일 수 있으리라 기대한다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.2
• /
• pp.101-106
• /
• 2021

In this paper, an inspection system has been developed where pneumatic instruments are used to stretch the film using compressed air, thus the curl problem can be overcome. When the pneumatic system is applied, a line scan camera should be used instead of an area camera because the COF surface makes an arc by the air pressure. The distance between the COF and the inspection camera should be kept constant to get a clear image, thus the position of COF is to be monitored on real-time. An operating software has been also developed which is switching on/off the pneumatic system, determining the COF position using a camera vision, displaying the contour of the COF side view, sending self-diagnosis result and etc. The developed system has been examined using the actual roll of COF, which convince that the system can be an effective device to inspect the COF rolls in process.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.8
• /
• pp.1899-1907
• /
• 2013

This paper presents an efficient defect detection and classification system based on reference image for COF (Chip-on-Film) which encounters fatal defects after ultra fine pattern fabrication. These defects include typical ones such as open, mouse bite (near open), hard short and soft short. In order to detect these defects, conventionally it needs visual examination or electric circuits. However, these methods requires huge amount of time and money. In this paper, based on reference image, the proposed system detects fatal defect and efficiently classifies it to one of 4 types. The proposed system includes the preprocessing of the test image, the extraction of ROI, the analysis of local binary pattern and classification. Through simulations with lots of sample images, it is shown that the proposed system is very efficient in reducing huge amount of time and money for detecting the defects of ultra fine pattern COF.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.33-42
• /
• 2015

오늘날 연성회로기판(FCCL : Flexible Copper Clad Laminate)은 디스플레이, 스마트폰, 자동차, 항공, 의료 기기, 산업용 컨트롤 기기 등 거의 모든 고급 전자 제품들에 사용되고 있다. 특히 디스플레이 분야에서는 뛰어난 연성과 내구성을 바탕으로 경박단소화에 유리할 뿐만 아니라 구동부에 적용이 가능한 장점 등으로 그 적용처가 점점 늘어나고 있는 추세이다. 이 가운데서도 LCD와 OLED의 구동소자(Display Driver IC)를 장착하는 COF(Chip on Film)는 대표적인 연성회로기판(FCCL) 적용 부품으로서, 최근 인기를 끌고 있는 디스플레이의 제로-베젤(Zero-bezel)을 가능케 하는 핵심 부품이다. COF용 연성회로기판(FCCL) 소재로는 우수한 평탄도, 파인피치(Fine-pitch)구현성, 내굴곡성, 광투과성 등을 보유하고 있는 Sputtering Type FCCL이 사용되고 있다. 특히 최근 Display 분야의 화두가 되고 있는 POLED(Plastic-OLED) 패널을 장착한 Flexible Mobile 디스플레이의 경우, 기존의 COG(Chip on Glass) 접합방식이 아닌 COF 접합방식을 채택하고 있으며, 기존의 단면 COF보다 3배의 고해상도 구현이 가능한 양면 COF를 채택하기에 이르렀다. 기존의 COF 제작공정과 달리 Semi Additive 공정으로 제작되는 양면 COF 시장의 태동으로 양면 연성회로기판(FCCL)의 수요 증가가 예상되는 등 최근 디스플레이 기술 발전은 소재 분야에도 큰 변화를 잉태하고 있다. 이러한 최근 디스플레이 업계의 고해상도, 고속 신호 전송, 슬림화, Flexible 추세에 대응 가능한 최적의 특성을 보유하고 있는 Sputtering Type FCCL을 중심으로 디스플레이의 발전에 대응하는 소재의 기술 개발 동향을 살펴보고자 한다.