• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.514-519
• /
• 2000

Recently a considerable interest is being concentrated on industrial applications of supersonic Coanda wall jets, but the flow physics are not still understood well. It is of practical importance to evaluate the effectiveness of supersonic Coanda wall jet devices fer such industrial purposes. In the present work, experiments and computations were performed to Set a better understanding of the supersonic Coanda jet physics. The experiments were made using a small blow-down wind tunnel. The operating pressure ratio and the Coanda surface configuration were changed to investigate their influences on the wall jet flows. Two-dimensional Navier-Stokes computations were performed using a TVD finite volume scheme to effectively capture the important wave structures of supersonic Coanda jet flows. Both experimental and computational results showed several important hysterical features of the supersonic Coanda wall jets; the attachment and detachment of supersonic Coanda jet were strongly dependent on the change processes of the operating pressure ratio and the detailed flow configuration.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.106-109
• /
• 2005

The Coanda effect has been used extensively in various aerodynamic applications to improve the system performance. The primary flow in Coanda ejectors is attached to the ejector wall and is expanded inducing a secondary flow. This will probably lead to the mixing of both primary and secondary flows at a down stream section. Very few works have been reported based on the optimization on such devices. The main objective of the present study is to numerically investigate the flow field on a typical Coanda ejector and validate the results with the available experimental data. Many configurations of the Coanda ejector have been analyzed. The effect of various geometric parameters of the device on the expanding mixing layer has also been obtained. The computed data agree fairly well with the experimental data available.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.11
• /
• pp.927-933
• /
• 2012

The characteristics of two-dimensional supersonic coanda flow was experimentally investigated. For various ratios of slot height to coanda wall's radius of curvature, surface roughnesses, and jet stagnation pressures, the characteristics of the supersonic coanda flow such as shock structures and hysteresis were observed by flow visualization. It was found that the characteristics of hysteresis of the coanda jet was related to the surface roughness of the coanda wall. The study was further extended for application of the tangentially injected coanda jet to control co-flowing highly compressible main jet direction. It was noticed that the stagnation pressure of the main jet as well as the ratio of the slot height to coanda wall's radius of curvature wall was an influencing factor in the performance of the fluidic thrust vectoring method.

• Journal of Ship and Ocean Technology
• /
• v.8 no.2
• /
• pp.13-19
• /
• 2004

Jet flows applied tangential to a foil surface near the leading and/or trailing edges increase the lift of the foil by delaying the separation also known as the Coanda effects. Many experimental and numerical studies have proven the effectiveness of Coanda effects on circulation control and the effects have been found to be useful in practical application in many aerodynamics fields. Most of the previous works have studied the effects of the jet blowing near the trailing edges and investigated the influence of jet momentum on lift. A few experimental studies, however, focused on the separation bubble that develops near the leading edge and applied jet flow the edge to remove the bubble but only to find decrease in lift. In the present paper, a Coanda foil of 20% thickness ellipse with modified rounded leading and trailing edges was investigated, and the flow around the foil was numerically studied. The blowing around the leading edge only decreased the lift, as the experiments showed, but the suction considerably increased the lift.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.12
• /
• pp.967-972
• /
• 2013

A MILD (Moderate and Intense Low oxygen Dilution) combustion, which is effective in the reduction of NOx, is considerably affected by the recirculation flow rate of hot exhaust gas to the combustion furnace. The present study used the MILD combustor, which has coaxial cylindrical tube. The outside tube of the MILD combustor corresponds to the exhaust gas passage and the inner side tube is the furnace passage. A numerical analysis was accomplished to elucidate the characteristics of exhaust gas entrainment toward the inner furnace with the changes of coanda nozzle geometrical parameters, nozzle passage gap length, nozzle passage length, nozzle angle and expansion length. The optimal configuration of coanda nozzle for the best entrainment flow rate was gap length, 0.5 mm, expansion angle, 4o and expansion length, 146 mm. The nozzle passage length was irrelevant to the exhaust gas entrainement.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.42.2-42.2
• /
• 2005

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.10a
• /
• pp.33-33
• /
• 1999

The Coanda effect is the tendency for a fluid jet to atach itself to an adjacent surface and follow its contour without causing an appreciable flow separation. The jet is pulled onto the surface by the low pressure region which develops as entrainment pumps fluid from the region between the jet and the surface. Then the jet is held to the wall surface by the resulting radial pressure gradient which balance the inertial resistance of the jet to turning. The jet may attach to the surface and may be deflected through more than 180 dog, when the radius of the Coanda surface is sufficiently large compared to the height of the exhaust nozzle. However, if the radius of curvature is small, the jet turns through a smaller angle, or may not attach to the surface at all. In general, the limitations in size and weight of a device will limit the radius of the deflection surface. Thus much effort has been paid to improve the jet deflection in a variety of engineering fields. The Coanda effect has long been applied to improve aerodynamic characteristics, such as the drag/lift ratio of flight body, the engine exhaust plume thrust vectoring, and the aerofoil/wing circulation control. During the energy crisis of the seventies, the Coanda jet was applied to reduce vehicle drag and led to drag reductions of as much as about 30% for a trailer configuration. Recently a variety of industrial applications are exploiting another characteristics of the Coanda jets, mainly the enhanced turbulence levels and entrainment compared with conventional jet flows. Various industrial burners and combustors are based upon this principle. If the curvature of the Coanda surface is too great or the operating pressure too high, the jet flow will break away completely from the surface. This could have catastrophic consequences for a burner or combustor. Detailed understanding of the Coanda jet flow is essential to refine the design to maximize the enhanced entrainment in these applications.

• Journal of the Korean Institute of Gas
• /
• v.21 no.3
• /
• pp.53-60
• /
• 2017

Various researches have been conducted for the reduction of NOx at the combustion furnace and exhaust gas recirculation method is commonly used technology for NOx reduction. The present research adopted coanda nozzles at the outside pipes of furnace to entrain the exhaust gas for the exhaust gas recirculation and the mixed gas was ejected to the tangential direction to cause the swirl flow in the furnace. The combustion flow characteristics in the exhaust gas recirculation burner with coanda nozzle has been elucidated by analyzing the swirl flow streamlines, temepraure and reaction rate distribution in the furnace. The exhaust gas entrained flow rate has been investigated by changing the excess air factor and coanda nozzle gap and the exhaust gas entrained flow rate increased with the increase of excess air factor and it decreased with the increase of coanda nozzle gap. The mean temperature at the exit plane of exhaust gas decreased with the excess air factor and it was little affected by the increase of coanda nozzle gap. The NOx mass fraction at the exhaust gas exit plane remarkably decreased with the excess air factor and it was also little affected by the increase of coanda nozzle gap.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.81.1-81.1
• /
• 2005

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.6
• /
• pp.569-578
• /
• 2008

The Coanda effects demonstrate that a jet stream applied tangential to a curved surface can generate lift force by increasing the circulation. Many experimental and numerical studies have been performed on the Coanda effect and it is found to be useful in various fields of aerodynamics. The Coanda effect may have practical application to marine hydrodynamics since various control surfaces are being used to control behaviors of ships and offshore structures. In the present study, numerical computations are performed to find the applicability of the Coanda effect to the marine control surfaces. For the purpose, changes in flow characteristics around a flapped foil due to the Coanda effect have been simulated by RANS equations discretized with a cell-centered finite volume method (FVM). In the process, special attention has been given to the influence of jet nozzle arrangement on the lift characteristics of the Coanda foil. It is found that the shape as well as the location of the jet intake and jet exit affects the lift performance of the foil significantly.