• Journal of the Korean Society of Combustion
• /
• v.13 no.1
• /
• pp.1-9
• /
• 2008

Emission characteristics of NOx and CO with heat loss under high efficiency combustion conditions of $CH_4$/Air prmixed flame were examined numerically using detailed-kinetic chemistry. The one-dimensional combustor length was fixed 5cm, and the equivalence ratio was varied from 0.75 to 0.95. To consider the effects of heat loss on NOx and CO formation, the radiative heat loss rate and combined heat loss rate of conductive and convective heat transfer are included. The following conclusions were drawn. In order to reduce the NOx and CO emission level simultaneously, the temperature of product gases must be reduced under 1,800K as soon as possible but kept over 1,300K during the residence time which is needed to converge CO to $CO_2$.

• Journal of Embryo Transfer
• /
• v.15 no.1
• /
• pp.67-75
• /
• 2000

This study was conducted to establish the optimal conditions for in vitro embryo production using oocytes derived from follicles of slaughter-house ovaries. The ovaries of Hanwoo were obtained from a local slaughter-house. The oocytes were aspirated from visible follicles of 2~7mm in diameter. The recovered oocytes which were completely surrounded by at least 2 layers of cumulus cells and a homogeneous cytoplasmic pigmentation were used. The selected oocytes were washed 3 or 4 times with D-PBS containing 10% bovine calf serum (BCS) and matured in vitor (IVM) in Ham's F-10 supplemented with 10% BCS or 0.01 $\mu\textrm{g}$/ml epidermal growth factor(EGF) at 39$^{\circ}C$ under 5% CO2 in air for 24 hours. They were fertilizqed in vitro (IVF) with fresh sperm separated by Percoll density gradient or swim-up in TALP media. The zygotes were cultrued with or without bovine oviductal epitherial cells(BOEC) in media(HECM-6 supplemented with 11 amino acid and / or TCM-199 supplemented with 10% BCS) for 7 to 10 days. The results obtained were as follow: The cleavage rate and developmental rate to blastocyst after maturation and IVF were not significantly different between Ham's F-10 with EGF(76.0% vs. 44.0%) and BCS(75.9% vs. 43.6%)(P<0.05). The cleavage rate and development rate to blastocyst after fertilizing by swim-up or Percoll method were not signifciantly(P<0.05) different between swim-up (80.2% vs. 29.2%) and Percoll(81.9% vs. 26.5%) (P<0.05). The cleavage rate in TCM 199(80.5) was signficiantly higher than that in HECM-6 (72.0%) (P<0.05). However, developmental rate to blastocyst using TCM 199 following HECM-6 for 3 or 4 days (42.2%) was significantly higher than that in TCM-199 alone(26.7%)(P<0.05). The cleavage rate and development rate of embryos produced in vitro by exchange timing for HECM-6 media were not significantly different between in day 3(78.6% vs. 45.5%) and day 4(75.0% vs. 43.2%)(P<0.05). The cleavage rate and developmental rate to blastocysts according to co-culture system were not significantly different between with (74.2% vs. 41.4%) and without BOEC(73.95 vs. 43.5%) (P<0.05). The number of blastomere in blastocyst stage after co-culture with or without BOEC was not significantly different (106.7$\pm$5.1 and 96.6$\pm$4.0). In conclusion, the most transferable IVP embryos could be produced from Ham's F-10 medium for IVM, Percoll density gradient method for IVF sperm separation and in vitro culture in HECM-6 until day 3 or day 4, and then transferred into TCM-199 until day 9 within adequate embryo density in culture droplets after insemination.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.1
• /
• pp.72-79
• /
• 2009

The effect of symmetric and asymmetric micro regenerative pump impellers on their pressure performance was studied. The shut off head of the pump with the symmetric impeller was about 2.5 times as that with the asymmetric impeller. The computation of the internal flow was performed to clarify the cause of the increase of the head. It was found that the contribution of the angular momentum supply was larger than that of shear stress for the head development in both cases. The larger head and momentum supply in the case of the symmetric impeller were caused by larger recirculated flow rate and larger angular momentum difference between the inlet and outlet to the impeller. The larger recirculated flow rate was caused by smaller pressure gradient in the direction of recirculated flow. The decrease of the circumferential velocity in the casing was attributed to the smaller local flow rate in the casing.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.8
• /
• pp.1035-1040
• /
• 2011

In this study, many researches have been carried out against Energy Efficiency Operational Indicator(EEOI) of existing ships under discussion by IMO. This research is examined the method for the polices about IMO's greenhouse gas reducing emissions among them, we were analyzed the EEOI for existing ships. we have analyzed the result about applying EEOI using the calculation method of the rate of fuel consumption for cargo quantities to the actual existing ships and raised the problem. Based on this research, we were presented the improved EEOI about the engine load using fuel consumption and applied the existing ships. As a result, we concluded that the improved EEOI can define a resonable rate of $CO_2$ emissions.

• Journal of Hydrogen and New Energy
• /
• v.21 no.1
• /
• pp.42-49
• /
• 2010

Increasing environmental concerns regarding the use of fossil fuels and global wanning have prompted researcher to investigate alternative fuels. The purpose of this study is to investigate the syngas production by biogas reforming using a compression spark ignition engine. The parametric screening studies were carried out according to the variations of oxygen enrichment rate, biogas $CO_2$ ratio, intake gas temperature, and engine revolution. When the oxygen enrichment rate and input gas temperature increased, hydrogen and carbon monoxide were increased. But the biogas $CO_2$ ratio and engine revolution increased, the syngas were reduced. For the reforming of methane 100% only, generation of hydrogen and carbon monoxide was 58% and 17%, respectively. However when the biogas $CO_2$ ratio was 40%, hydrogen and carbon monoxide concentration were about 20% each.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2192-2194
• /
• 1999

In this study, We have accomplished a new approach to develope a cheap and compact pulsed $CO_2$ laser system. We used a fast SCR as switching device instead of a thyatron in the pulsed power supply. Using the Pulse transformer, energy in the condenser is tranferred to the secondary, electrodes of discharge tube, from the primary. An axial and water cooled type was adopted as the laser cavity. The laser performance characteristics as various parameters, such as gas pressure and pulse repetition rate, have been investigated. As a result, the maxium laser output was 12.3[W] at a pulse repetition rate of 120[pps] and a filling pressure of 12[Torr].

• BMB Reports
• /
• v.29 no.4
• /
• pp.277-285
• /
• 1996

In Pseudomonas fluorescens grown on malonate as sole carbon source, acetyl-CoA synthetase was induced, suggesting that malonate is metabolized through acetate and then acetyl-CoA. Acetyl-CoA synthetase was purified 18.6-fold in 4 steps to apparent homogeneity. The native molecular mass of the enzyme estimated by a native acrylamide gel electrophoresis was 130 kDa. The enzyme was composed of two identical subunits with a molecular mass of 67 kDa. Optimum pH was 70. The acetyl-CoA synthetase showed typical Michaelis-Menten kinetics for the substrates, acetate, ATP and CoA, whose $K_m$ values were calculated to be 33.4, 74.8, and 40.7 mM respectively. Propionate. butyrate and pentanoate were also used as substrates by the enzyme, but the rate of the formation of the CoA derivatives was decreased in the order of the increase in carbon number. The enzyme was inhibited by the group-specific reagents diethylpyro-carbonate, 2,3-butanedione, pyridoxal-5'-phosphate and N-bromosuccinimide. In the presence of substrates the inactivation rate of the enzyme, by all of the group-specific reagents mentioned above decreased, indicating the presence of catalytically essential histidine, arginine, lysine and tryptophan residues at or near the active site. Preincubation of the enzyme with ATP, $Mg^{2+}$ resulted in the increase of its susceptibility to diethylpyrocarbonate, suggesting that ATP, $Mg^{2+}$ may induce a conformational change in the active site exposing the essential histidine residue to diethylpyrocarbonate. The enzyme was acetylated in the presence of acetyl-CoA, indicating that this is one of acyl-enzyme.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.4
• /
• pp.431-443
• /
• 2007

Statement of problem: Injuries along with discomfort may result on the oral mucosa when non-rigid material is used as the major connector in construction of RPD, since nonrigid major connectors transmit unstable forces throughout the appliance. Titanium which recently draws attention as a substitute of Co-Cr had a difficulty in fabricating due to high melting temperature but the development of casting technique makes it possible to apply to the clinical case. Purpose: The purpose of this study was to investigate the rigidity and the castability of titanium upper major connector by design and make a comparison with Co-Cr major connectors which are widely used in clinical cases now. Material and methods: Casting was done using CP-Ti(Grage 2) (Kobe still Co., Japan) for the experimental groups, and 4 various designs namely palatal strap, U-shaped bar, A-P strap, and complete palatal plate were casted and 5 of each designs were included in each group. For the experimental group, Universal testing machine (Model 4502; Instron, Canton, Mass) was used to apply vertical torsional force vertically to the horizontal plane of major connector. In the second experiment, Vertical compressive force was applied to the horizontal plane of major connector. As a comparative group, Co-Cr major connector was equally manufactured and underwent the same experimental procedures Strain rate was measured after constant loading for one minute duration, and statistical analysis was done with SPSS ver.10.0 for WIN(SPSS. Inc. USA). From the one-way ANOVA and variance analysis (P=0.05), Scheffe's multiple comparison test implemented. Results: 1. Least amount of strain was observed with complete palatal plate followed by A-P bar, palatal bar, and the U-shaped bar having most amount of strain. 2. In all designs of titanium major connector, less strain rate was observed under compressive loading than under torsional loading showing more resistance to lateral force. 3. For titanium major connector, less strain rate was observed when the force is applied to the first premolar area rather than to the second molar area indicating more strength with shorter length of lever. 4. In Comparison of Co-Cr major connector with titanium major connector, palatal strap and U-shaped bar designs showed higher strength under torsional force that is statically significant, and under compressive force, no significant difference was observed expert for U-shaped bar. 5. In titanium major connector, complete palatal plate showed lowest success rate in casting when compared with the Co-Cr major connector. Conclusion: Above results prove that when using titanium for major connector, only with designs capable of generating rigidity can the major connector have almost equal amount of rigidity as Co-Cr major connector and show lower success rate in casting when compared with the Co-Cr major connector.

• Membrane and Water Treatment
• /
• v.10 no.4
• /
• pp.265-275
• /
• 2019

This study aimed to develop a compact partial nitritation step by forming granules with high Ammonia-Oxidizing Bacteria (AOB) fraction using the Air-lift Granulation Reactor (AGR) and to evaluate the feasibility of treating reject water with high ammonium content by combination with the Anammox process. The partial nitritation using AGR was achieved at high nitrogen loading rate ($2.25{\pm}0.05kg\;N\;m-3\;d^{-1}$). The important factors for successful partial nitritation at high nitrogen loading rate were relatively high pH (7.5~8), resulting in high free ammonia concentration ($1{\sim}10mg\;FA\;L^{-1}$) and highly enriched AOB granules accounting for 25% of the total bacteria population in the reactor. After the establishment of stable partial nitritation, an effluent $NO_2{^-}-N/NH_4{^+}-N$ ratio of $1.2{\pm}0.05$ was achieved, which was then fed into the Anammox reactor. A high nitrogen removal rate of $2.0k\; N\;m^{-3}\;d^{-1}$ was successfully achieved in the Anammox reactor. By controlling the nitrogen loading rate at the partial nitritation using AGR, the influent concentration ratio ($NO_2{^-}-N/NH_4{^+}-N=1.2{\pm}0.05$) required for the Anammox was controlled, thereby minimizing the inhibition effect of residual nitrite.

• Journal of Korea Society of Waste Management
• /
• v.35 no.7
• /
• pp.606-615
• /
• 2018

Over the past two decades, the options for solid waste management have been changing from land disposal to recycling, waste-to-energy, and incineration due to growing attention for resource and energy recovery. In addition, the reduction of greenhouse gas (GHG) emission has become an issue of concern in the waste sector because such gases often released into the atmosphere during the waste management processes (e.g., biodegradation in landfills and combustion by incineration) can contribute to climate change. In this study, the emission and reduction rates of GHGs by the municipal solid waste (MSW) management options in D city have been studied for the years 1996-2016. The emissions and reduction rates were calculated according to the Intergovernmental Panel on Climate Change guidelines and the EU Prognos method, respectively. A dramatic decrease in the waste landfilled was observed between 1996 and 2004, after which its amount has been relatively constant. Waste recycling and incineration have been increased over the decades, leading to a peak in the GHG emissions from landfills of approximately $63,323tCO_2\;eq/yr$ in 2005, while the lowest value of $35,962tCO_2\;eq/yr$ was observed in 2016. In 2016, the estimated emission rate of GHGs from incineration was $59,199tCO_2\;eq/yr$. The reduction rate by material recycling was the highest ($-164,487tCO_2\;eq/yr$) in 2016, followed by the rates by heat recovery with incineration ($-59,242tCO_2\;eq/yr$) and landfill gas recovery ($-23,922tCO_2\;eq/yr$). Moreover, the cumulative GHG reduction rate between 1996 and 2016 was $-3.46MtCO_2\;eq$, implying a very positive impact on future $CO_2$ reduction achieved by waste recycling as well as heat recovery of incineration and landfill gas recovery. This study clearly demonstrates that improved MSW management systems are positive for GHGs reduction and energy savings. These results could help the waste management decision-makers supporting the MSW recycling and energy recovery policies as well as the climate change mitigation efforts at local government level.