• 센서학회지
• /
• 제6권3호
• /
• pp.207-213
• /
• 1997

$H^{+}$ 이온에 선택적으로 감응하는 field effect transistor(pH-ISFET)를 바탕소자로 하고, 그 gate 주위에 Ag/AgCl 기준전극을 형성한 다음, 이를 둘러싼 수화젤(hydrogel)막 및 기체투과막의 이중막 구조를 가진 용존이산화탄소($CO_{2(aq)}$) 센서소자를 사진식각(photolithography)법으로 제작하였다. PVA-SbQ 혹은 PVP-PVAc/감광제 형의 광가교형 감광액은 수화젤막 형성에 적합하지 않았으나, 2-hydroxyethyl methacrylate(HEMA) 및 acrylamide를 포함하는 광중합형 감광액을 사용할 경우에는 사진식각법에 의한 수화젤막이 좋은 해상도로 얻어졌다. 기체투과막은 urethane acrylate계 UV-oligomer를 주성분으로 한 감광액을 써서 사진식각법으로 수화젤막위에 형성할 수 있었다. 또한 수화젤막 및 기체투과막을 사진식각법으로 형성할 때 N,N,N',N'-tetramethyl ethplenediamine(TED) 을 $O_{2}$ quencher로서 감광액 중에 도입함으로써 UV 노광시에 polyester film을 부착하는 번거로운 공정을 생략할 수 있음을 알았다. 이렇게 제조된 $pCO_{2}$ 센서는 수용액 중에서 $10^{-3}{\sim}10^{0}\;mol/{\ell}$의 $CO_{2}$ 농도변화에 대하여 직선적인 검정곡선(calibration curve)을 얻을 수 있었다.

• 센서학회지
• /
• 제22권4호
• /
• pp.286-291
• /
• 2013

This paper presents to analyze patterns from single and complex malodors using gas sensor array based on metal oxide semiconductors. The aim of research is to identify and discriminate single malodors such as $NH_3$, $CH_3SH$ and $H_2S$ and their mixtures according to concentration levels. Measurement system for analyzing patterns from malodors is constructed by an array of metal oxide semiconductor sensors which are available commercially together with associate electronics. The patterns from sensory system are analyzed by Principal Component Analysis (PCA) which is simple statistical pattern recognition technique. Throughout the experimental trails, we confirmed the experimental procedure for measurement system such as sensors calibration time and gas flow rate, and discriminated malodors using pattern analysis technique.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.66-66
• /
• 2011

Anodic titanium dioxide (TiO2) nanotubes are very attractive materials for gas sensors due to its large surface to volume ratios. The most widely known method for fabrication of TiO2 nanotubes is anodic oxidation of metallic Ti foil. Since the remaining Ti substrate is a metallic conductor, TiO2 nanotube arrays on Ti are not appropriate for gas sensor applications. Detachment of the TiO2 nanotube arrays from the Ti Substrate or the formation of electrodes onto the TiO2 nanotube arrays have been used to demonstrate gas sensors based on TiO2 nanotubes. But the sensitivity was much lower than those of TiO2 gas sensors based on conventional TiO2 nanoparticle films. In this study, Ti thin films were deposited onto a SiO2/Si substrate by electron beam evaporation. Samples were anodized in ethylene glycol solution and ammonium fluoride (NH4F) with 0.1wt%, 0.2wt%, 0.3wt% and potentials ranging from 30 to 60V respectively. After anodization, the samples were annealed at $600^{\circ}C$ in air for 1 hours, leading to porous TiO2 films with TiO2 nanotubes. With changing temperature and CO concentration, gas sensor performance of the TiO2 nanotube gas sensors were measured, demonstrating the potential advantages of the porous TiO2 films for gas sensor applications. The details on the fabrication and gas sensing performance of TiO2 nanotube sensors will be presented.

• 센서학회지
• /
• 제29권6호
• /
• pp.388-393
• /
• 2020

In this study, a PbS quantum dots (QDs)-based H₂ gas sensor with a Pd electrode was proposed. QDs have a size of several nanometers, and they can exhibit a high surface area when forming a thin film. In particular, the NH₂ present in the ligand of PbS QDs and H₂ gas are combined to form NH₃⁺, subsequently the electrical characteristics of the QDs change. In addition to the resistance change owing to the reaction between Pd and H₂ gas, the resistance change owing to the reaction between the NH₂ of PbS QDs and H₂ gas increases the current signal at the sensor output, which can produce a high output signal for the same concentration of H₂ gas. Using the XRD and absorbance properties, the synthesis and particle size of the synthesized PbS QDs were analyzed. Using PbS QDs, the sensitivity was significantly improved by 44%. In addition, the proposed H₂ gas sensor has high selectivity because it has low reactivity with heterogeneous gases such as C₂H₂, CO₂, and CH₄.

• 한국재료학회지
• /
• 제25권8호
• /
• pp.423-428
• /
• 2015

Impedancemetric $NO_x$ (NO and $NO_2$) gas sensors were designed with a stacked-layer structure and fabricated using $LaCr_xCo_{1-x}O_3$ (x = 0, 0.2, 0.5, 0.8 and 1) as the receptor material and $Li_{1.3}Al_{0.3}Ti_{1.7}(PO_4)_3$ plates as the solid-electrolyte transducer material. The $LaCr_xCo_{1-x}O_3$ layers were prepared with a polymeric precursor method that used ethylene glycol as the solvent, acetyl acetone as the chelating agent, and polyvinylpyrrolidone as the polymer additive. The effects of the Co concentration on the structural, morphological, and $NO_x$ sensing properties of the $LaCr_xCo_{1-x}O_3$ powders were investigated with powder X-ray diffraction, field emission scanning electron microscopy, and its response to 20~250 ppm of $NO_x$ at $400^{\circ}C$ (for 1 kHz and 0.5 V), respectively. When the as-prepared precursors were calcined at $700^{\circ}C$, only a single phase was detected, which corresponded to a perovskite-type structure. The XRD results showed that as the Co concentration of the $LaCr_xCo_{1-x}O_3$powders increased, the crystal structure was transformed from an orthorhombic phase to a rhombohedral phase. Moreover, the $LaCr_xCo_{1-x}O_3$ powders with $0{\leq}x<0.8$ had a rhombohedral symmetry. The size of the particles in the $LaCr_xCo_{1-x}O_3$powders increased from 0.1 to $0.5{\mu}m$ as the Co concentration increased. The sensing performance of the stack-structured $LaCr_xCo_{1-x}O_3/Li_{1.3}Al_{0.3}Ti_{1.7}(PO_4)_3$ sensors was found to divide the impedance component between the resistance and capacitance. The response of these sensors to NO gas was more sensitive than that to $NO_2$ gas. Compared to other impedancemetric sensors, the $LaCr_{0.8}Co_{0.2}O_3/Li_{1.3}Al_{0.3}Ti_{1.7}(PO_4)_3$ sensor exhibited good reversibility and reliable sensingresponse properties for $NO_x$ gases.

• 센서학회지
• /
• 제21권3호
• /
• pp.167-171
• /
• 2012

Ag- and Pd-loaded $SnO_2$ nanowire network sensors were prepared by the growth of $SnO_2$ nanowires via thermal evaporation, the coating of slurry containing $SnO_2$ nanowires, and dropping of a droplet containing Ag or Pd nanoparticles, and subsequent heat treatment. All the pristine, Pd-loaded and Ag-loaded $SnO_2$ nanowire networks showed the selective detection of $C_2H_5OH$ with low cross-responses to CO, $H_2$, $C_3H_8$, and $NH_3$. However, the relative gas responses and gas selectivity depended closely on the catalyst loading. The loading of Pd enhanced the responses($R_a/R_g$: $R_a$: resistance in air, $R_g$: resistance in gas) to CO and $H_2$ significantly, while it slightly deteriorated the response to $C_2H_5OH$. In contrast, a 3.1-fold enhancement was observed in the response to 100 ppm $C_2H_5OH$ by loading of Ag onto $SnO_2$ nanowire networks. The role of Ag catalysts in the highly sensitive and selective detection of $C_2H_5OH$ is discussed.

• 한국전기전자재료학회논문지
• /
• 제24권3호
• /
• pp.215-218
• /
• 2011

A novel design of gas sensor using Ga-doped ZnO (GZO) thin films which are deposited on low temperature co-fired ceramic (LTCC) substrates is presented. The LTCC substrates with thickness of 400 ${\mu}m$ are fabricated by laminating 12 green tapes which consist of alumina and glass particle in an organic binder. The GZO thin films with different thickness are deposited on LTCC substrates, by RF magnetron sputtering method. The microstructure and sensing properties of GZO gas sensing films are analyzed as a function of the film thickness. The films are well crystallized in the hexagonal (wurzite) structure with increasing thickness. The maximum sensitivity of 3.49 is obtained at 100 nm film thickness and the fastest 90% response time of 27.2 sec is obtained at 50 nm film thickness for the operating temperature of $400^{\circ}C$ to the $NO_2$ gas.

• 센서학회지
• /
• 제7권3호
• /
• pp.188-196
• /
• 1998

$WO_{3}$계 n-형 반도체 가스센서의 검지특성 및 전기적 특성을 조사하였다. 공기중에서 결합제가 첨가되지 않은 $WO_{3}:TiO_{2}$(4 wt. %) 센서의 낱알경계에서의 전위장벽의 크기는 0.26 V로 나타났으며, 결합제로서 $Al_{2}O_{3}$, PVA (polyvinyl alcohol ), silica sol이 첨가된 센서의 경우는 전위장벽이 각각 0.17, 0.22, 0.26 V로 관측되었다. 이들 시료를 $NO_{x}$가 120 ppm 첨가된 분위기에 노출시켰을 때, 결합제가 첨가되지 않은 센서의 경우는 낱알경계에서의 전위장벽이 0.59 V로 증가하였으며, 결합제로서 $Al_{2}O_{3}$, PVA, silica sol이 첨가된 경우는 전위장벽이 각각 0.43, 0.66, 0.52 V로 나타나, PVA가 첨가된 센서에서 전위장벽의 변화가 가장 높아 감도가 우수하게 되는 것을 알 수가 있었다. 한편 센서 최적 작동온도 이상의 온도에서 나타나는 감도의 감소는 흡착가스 입자의 탈착보다는 공기중에서 다결정이 보이는 저항의 온도 의존성에 따라 나타남이 판명되었다. 또한 결합제가 첨가되지 않은 센서와 결합제로서 Pt가 첨가된 센서의 경우, CO가 250 ppm 존재할 때까지도 전위장벽의 크기가 약 0.2 V로 공기중에서와 비슷한 크기를 나타내어, CO와 $NO_{x}$가 혼합된 분위기에서 $NO_{x}$만을 선택적으로 검지하는데 유리함이 밝혀졌다.

• 센서학회지
• /
• 제17권4호
• /
• pp.273-280
• /
• 2008

Monolith aperture-type oxygen sensors with simple structure of YSZ(pin-hole)/Pt/ YSZ(solid electrolyte)/Pt were fabricated by co-firing technique. To enhance the yield of productivity, a couple of YSZ green sheets for diffused barrier and solid electrolyte were prepared by tape-casting and co-firing method. The limit current characteristics of the oxygen sensors were measured between 500 and $650^{\circ}C$ The heating temperature of $600^{\circ}C$ was optimum as a portable oxygen sensor in the range of oxygen concentration from 0 to 75 vol%. Linear proficiency of limit current behavior as a function of oxygen concentration was controlled by the variation of aperture dimension. The fabricated oxygen sensors showed the stable sensing output for 30 days. Gas leakage in bonding area due to warping, cracking and thermal cycling was not found in the period.

• 센서학회지
• /
• 제25권3호
• /
• pp.173-177
• /
• 2016

Tape casting ceramics technology has been adopted for the fabrication of solid state electrochemical $CO_2$ sensors and the packaging substrates. The fabricated $CO_2$ sensors exhibit a fast response and a good recovery with the almost theoretical sensitivity of 37 mV/decade, corresponding to a sensor operating temperature of 373 K. The two packaging methods, the wire bonding package and the surface- mounted on the ceramic package, were compared with respect to their power consumption and mass production feasibility. In terms of the ease of fabrication, the surface mount packaging technology is superior to the wire bonding technology but its power consumption is approximately twice that of the wired package.