• Advances in nano research
• /
• v.2 no.1
• /
• pp.23-56
• /
• 2014

The significant growth of the Si photovoltaic industry has been so far limited due to the high cost of the Si photovoltaic system. In this regard, the most expensive factors are the intrinsic cost of silicon material and the Si solar cell fabrication processes. Conventional Si solar cells have p-n junctions inside for an efficient extraction of light-generated charge carriers. However, the p-n junction is normally formed through very expensive processes requiring very high temperature (${\sim}1000^{\circ}C$). Therefore, several systems are currently under study to form heterojunctions at low temperatures. Among them, carbon nanotube (CNT)/Si hybrid solar cells are very promising, with power conversion efficiency up to 15%. In these cells, the p-type Si layer is replaced by a semitransparent CNT film deposited at room temperature on the n-doped Si wafer, thus giving rise to an overall reduction of the total Si thickness and to the fabrication of a device with cheaper methods at low temperatures. In particular, the CNT film coating the Si wafer acts as a conductive electrode for charge carrier collection and establishes a built-in voltage for separating photocarriers. Moreover, due to the CNT film optical semitransparency, most of the incoming light is absorbed in Si; thus the efficiency of the CNT/Si device is in principle comparable to that of a conventional Si one. In this paper an overview of several factors at the basis of this device operation and of the suggested improvements to its architecture is given. In addition, still open physical/technological issues are also addressed.

• Fibers and Polymers
• /
• v.7 no.1
• /
• pp.85-87
• /
• 2006

The tensile-recoil compressional behavior of the carbon nanotube reinforced mesophase pitch (MP)-based composite carbon fibers (CNT-re-MP CFs) was investigated by using Instron and SEM. The CNT-re-MP CFs exhibited improved, or at least equivalent, compressive strength as compared with commercial MP-based carbon fibers. Particularly, when CNT of 0.1 wt% was reinforced, the ratios of recoil compressive strengths to tensile strength of CNT-re-MPCFs were much higher (the difference is at least 10 % or higher) than those for the commercial counterparts and even than those for PAN-based commercial carbon fibers. FESEM micrographs showed somewhat different fractography from that of a typical shear failure as the CNT content increased.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.12
• /
• pp.59-63
• /
• 2017

In the cold region, road surface is frequently frozen, resulting in property/facility damage as well as people's death. In order to prevent the road surface from being frozen, conventional deicing methods such as salt, geothermal, and electric wires have been widely used. However, theses methods have some problems such as anti-environment, high-construction and -maintenance cost and so on. To improve the drawbacks of aforementioned methods, carbon nanotube (CNT) was used as an heating material in the laboratory test. Through the test, heat transferring effect of CNT on the concrete slab was investigated and maximum interval of CNT installation was determined.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.314-317
• /
• 2002

Since the early work of Tersoff and Hamann on the theory of the scanning tunneling microscope (STM), many theoretical approaches have been developed in order to gain further physical insight into the real space image that this technique provides. In this Paper, the STM image of Carbon nanotubes (CNT's) was calculated through the theoretical study. The optimized structure of CNT's was simulated using Brenner's hydrocarbon potential. The structure of simulation is (5. 5) armchair CNT and (10. 0) zigzag CNT. Also we have used that the extended Huckel tight binding (EHTB) theory already provides a fairly good qualitative description of the main processes that control the final contrast in the STM image. we found that the shape of the calculated images is hardly dependent on the exact electronic charge distribution at the surface. The STM images are not too sensitive to the precise electronic structure but, rather, they reflect its qualitative features. As a result of the simulation, The STM images of CNT's and the electronic density distribution were investigated. It found that the EHTB theory is appropriate for STM image calculation and that the STM images are in agreement with the result of Experiment.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03b
• /
• pp.43-43
• /
• 2010

we have investigated the field emission characteristics of the CNT/TEOS hybrid thin films fabricated by a spray method. It is found that the CNT/TEOS hybrid emitters show high current density, low turn on field, and long-term emission stability compared to the CNT emitters. These efficient field emission characteristics of the CNT/TEOS hybrid emitters are attributed to the TEOS sol, acting as a protection layer of nanotube emitter by surrounding the nanotube tip as well as a binder material to enhance the adhesion of nanotube emitters to the substrate. Therefore, the CNT/TEOS hybrid emitters could be utilized as an alternative for the efficient and reliable field emitters.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.4
• /
• pp.378-385
• /
• 2016

In this study, we synthesized a biocatalyst consisting of glucose oxidase (GOx), polyethyleneimine (PEI) and carbon nanotube (CNT) with addition of glutaraldehyde (GA)(GA/[GOx/PEI/CNT])for fabrication of glucose sensor. Main bonding of the GA/[GOx/PEI/CNT] catalyst was formed by crosslinking of functional end groups between GOx/PEI and GA. Catalytic activity of GA/[GOx/PEI/CNT] was quantified by UV-Vis and electrochemical measurements. As a result of that, high immobilization ratio of 199% than other catalyst (with only physical adsorption) and large sensitivity value of $13.4{\mu}A/cm^2/mM$ was gained. With estimation of the biosensor stability, it was found that the GA/[GOx/PEI/CNT] kept about 88% of its initial activity even after three weeks. It shows GA minimized the loss of GOx and improved sensing ability and stability compared with that using other biocatalysts.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.04a
• /
• pp.117-120
• /
• 2003

Electro-micromechanical techniques were applied using four-probe method for carbon nanotube (CNT) or nanofiber (CNF)/epoxy composites with their content. Carbon black (CB) was used to compare with CNT and CNF. The fracture of carbon fiber was detected by nondestructive acoustic emission (AE) relating to electrical resistivity for double-matrix composites test. Sensing for fiber tension was performed by electro-pullout test under uniform cyclic strain. The sensitivity for fiber damage such as fiber fracture and fiber tension was the highest for CNT/epoxy composites, and in CB case they were the lowest compared with CNT and CNF. Reinforcing effect of CNT obtained from apparent modulus measurement was the highest in the same content. The results obtained from sensing fiber damage were correlated with the morphological observation of nano-scale structure using FE-SEM. The information on fiber damage and matrix deformation and reinforcing effect of carbon nanocomposites could be obtained from electrical resistivity measurement as a new concept of nondestructive evaluation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.274-274
• /
• 2010

최근 들어 나노선을 이용한 pn 접합 소자 연구 결과가 매우 활발하게 보고되고 있다. 그러나, 서로 다른 두 종류의 나노선으로 pn 접합 어레이 구조의 소자를 제작할 때, 나노선을 원하는 위치에 정렬하는 기술상의 어려움이 큰 걸림돌이 된다. 본 연구에서는 p-CNT와 n-$SnO_2$ 나노선을 이용한 pn 접합 어레이 구조를 제작할 수 있는 독창적인 공정기술을 제안한다. 먼저 $SiO_2$가 300 nm 성장된 Si 기판을 선택적으로 패터닝하여 BOE (6:1) 용액으로 $SiO_2$ 층을 80 nm 정도 선택적으로 에칭한 후, 선택적으로 에칭된 표면에 슬라이딩 장비를 이용하여 화학기상증착법(chemical vapor deposition: CVD)으로 성장된 n-$SnO_2$ 나노선을 전이시킨다. 그 다음 thermal tape를 이용하여 CVD 법으로 성장된 랜덤 네트워크 형태의 CNT를 $SnO_2$ 나노선이 전이된 기판 위에 전이 시킨다. 이때 성장된 CNT 필름 중 금속성 나노선을 통한 전하 이동을 감소시키기 위해, 촉매로 사용되는 페리틴의 농도를 낮춰서 전체적인 CNT의 농도를 줄이는 방법을 이용하였다. 따라서, 성장된 CNT 필름은 별도의 후처리 없이 p-형의 반도체성을 보였다. 제작된 pn-소자는 정류비가 ~103 인 정류특성을 보였으며, 254 nm 파장의 UV lamp를 조사하여 광전류가 발생하는 것을 확인하였다. 연구결과는 이종의 나노선 접합에 의한 다이오드 응용과 UV 센서응용 가능성을 보여준다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.187.2-187.2
• /
• 2014

최근 다양한 카본 나노소재들이 열 전도성 필러로써 고분자 복합체의 열전도도 향상을 위해 연구되고 있다. 그러나 구조적 이방성을 갖는 탄소나노튜브(CNT) 혹은 그래핀나노플레이트(Graphene Nanoplatelet)를 복합체에 적용할 경우, 복합체의 수직 방향과 수평 방향에서의 열전도도가 3배 이상 차이가 나는 문제가 있다. 따라서 본 연구에서는 2차원의 GNP 표면 위에 1차원의 CNT를 직접 성장시킨 하이브리드 탄소소재를 이용하여 이러한 열전도도 이방성을 개선하고자 하였다. 하이브리드 탄소소재는 무전해 도금법과 열기상법으로 제조하였다. 합성된 하이브리드 탄소소재 및 CNT를 단독 혹은 혼합하여 필러를 만들고 이를 에폭시 기지 내에 분산시켜 복합체를 제작하였다. 필러 함량별, 필러 비율별로 제작된 복합체의 열전도도를 레이저 플래시 법으로 측정 비교하였다. 결과적으로 기존의 단일 필러들보다 열전도도 이방성이 1.5배 이상 개선된 방열용 에폭시 복합체를 제작할 수 있었다. 한편 하이브리드 탄소와 2% 이하의 CNT 배합에서 단독 필러 투입에 비해 45% 이상의 열전도율 향상을 확인하였다. 이는 미세구조 분석 및 성분 분석 결과, 필러 분산 정도가 열전도도 향상의 주요 인자로 작용하는 것을 확인하였고 기지 내 CNT가 열전도도 경로로 작용하기보다는 하이브리드 탄소소재의 균일한 분산에 영향을 준 것으로 사료된다.

• Composites Research
• /
• v.26 no.6
• /
• pp.373-379
• /
• 2013

The coating of metal surface with carbon nanotubes (CNTs) has been studied for the heat transfer enhancement of the boiling and condensation of refrigerant. The MWCNT/copper composite powder was made by the attrition ball milling, which has been coated on the copper wafer by electrostatic powder coating and sintered with electric furnace. In this paper, experiments were performed to assess the characterization and comparison of CNT before and after sinterning and the morphology changes of the CNT/Cu-coated surface. The samples were examined by the scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDAX) and raman spectroscopy. To verify the heat transfer enhancement, boiling heat transfer tests were performed.