• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.263.1-263.1
• /
• 2013

탄소나노튜브(CNT)를 이용한 초소형 X선 튜브는 근접 암치료, 비파괴 X선 영상 장치, 휴대용 X선 분광계 등에서 X선 발생소스로 많이 연구되고 있다. 2극형 CNT 에미터의 경우 구조가 단순하여 초소형 X선 튜브에 쉽게 장착할 수 있지만 아노드의 전압과 전류가 연동되기 때문에 튜브의 조작성이 제한적이다. 3극형은 상대적으로 복잡한 구조이고, CNT에서 방출된 전자가 게이트 전극으로 흐르는 누설 전류 그리고 절연체와 충돌하여 차징을 발생시킬 수 있기 때문에 직경이 좁은 초소형 X선 튜브에 구현하기가 쉽지 않다. 하지만 초소형 X선 튜브를 다양한 X선 장치에 응용하기 위해서는 아노드 전압과 전류의 독립된 조작이 가능한 3극형 CNT 에미터가 반드시 구현되어야 한다. 본 발표에서는 전자빔의 아노드 집속을 강화하고 절연체에서의 차징을 줄이는 포커싱 기능의 게이트(FFG) 구조를 제안하였고. 이를 적용하여 초소형 X선 튜브들을 제작하고, 분석하였다. FFG 구조가 성공적으로 적용된 초소형 X선 튜브는 게이트 누설 전류 없이 뛰어난 전류 및 X선 방출 특성을 보였다. 이와는 달리, 몇몇 초소형 X선 튜브들에서는 게이트 누설 전류가 나타났고, 아노드 전압에 의한 게이트 전압 상승이 발생하여 불안정한 구동 특성을 보였다. 초소형 X선 튜브를 밀봉하지 않고 진공 챔버에서 실험한 결과, 유도된 게이트 전압은 상당한 시간이 흐르거나 진공챔버에 공기를 주입하고 다시 진공상태로 만들면 유도전압이 제거되는 것을 볼 수 있었다. 결론적으로 CNT에서 방출된 전자빔이 정상궤도를 벗어나 게이트 누설전류와 차징에 의한 게이트 유도전압을 발생시키면 초소형 X선 튜브가 불안정한 구동을 하고, 결국 튜브의 심각한 결함으로 나타나게 된다. 즉, 게이트 누설 전류와 유도된 게이트 전압은 3극형 CNT 에미터가 장착된 초소형 X선 튜브의 디자인과 제작에 있어서 성공 기준이 될 수 있다.

• Korean Chemical Engineering Research
• /
• v.59 no.1
• /
• pp.35-41
• /
• 2021

Silicon is a promising next-generation anode material for lithium-ion battery, and it has been studied for commercialization due to the high theoretical capacity. However, it has problems of the volume change during charge-discharge and the poor electrical conductivity. To solve these problems, formation of SiO2 and carbon coating on the surface of silicon crystal were performed to protect the side reaction and enhance the electrical conductivity of silicon. CNT and CNF were also added to mitigate the volume change and increase the conductivity. Physical properties of asprepared samples were analyzed by XRD, SEM, and EDS. Electrochemical characteristics were investigated by electrical conductivity measurement, EIS, CV and cycle performance test. (Si/SiO2/C)+CNT&CNF showed high electrical conductivity and low charge-transfer resistance, and the capacity was 1528 mAh/g at 1st cycle and 1055 mAh/g at 50th cycle with 83% capacity retention.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.2
• /
• pp.126-129
• /
• 2021

We fabricated plate typed shunt resistors composed of carbon nanotube (CNT) and metal alloy for measuring DC current. CNT plates were prepared from dispersed CNT/Urethane solution by squeezing method. Cu/Ni alloys were prepared from composition-designed alloy wires for adjusting the temperature coefficient of resistance (TCR) by pressing them. As well, we fabricated a hybrid resistor by squeezing the CNT/Urethane solution on the metal alloy plate directly. In order to confirm the composition ratio of the Cu/Ni alloy, we used an energy-dispersed X-ray spectroscopy (EDX). Cross-section and surface morphology were analyzed by using a scanning electron microscopy (SEM). Finally, we measured the initial resistance of 2.35 Ω at 25℃ for the CNT paper resistor, 7.56 mΩ for the alloy resistor, and 7.38 mΩ for the hybrid resistor. The TCR was also measured to be -778.72 ppm/℃ at the temperature range between 25℃ to 125℃ for the CNT paper resistor, 824.06 ppm/℃ for the alloy resistor, and 17.61 ppm/℃ for the hybrid resistor. Some of the hybrid resistors showed a near-zero TCR of 1.38, -2.77, 2.66, and 5.49 ppm/℃, which might be the world best-value ever reported. Consequently, we could expect an error-free measurement of the DC current using this resistor.

• Animal Bioscience
• /
• v.35 no.11
• /
• pp.1800-1807
• /
• 2022

Objective: This study aimed to determine the effect of different cooling sessions (CSs) as a water conservation strategy on physiological, and production responses and welfare in Holstein Friesian cows during subtropical summer in Pakistan. Methods: Twenty-one cows were subjected to three CS in a completely randomized design. The treatments were: i) eleven hours continuous cooling with sprinklers - control (CNT), ii) four CS, and iii) two CS. The CNT represented the practices of the commercial dairy farms in the area, while the other CSs were used as water reduction strategies. Each CS lasted for 1 h with a 12 min cycle (3 min water on and 9 min off) with a sprinkler flow rate of 1.25 L/min. Results: The average temperature humidity index of the shed and the outside open area were 81.9 and 82.5, respectively. The results showed that both physiological responses were highest in the 2CS group followed by the CNT and the 4CS (p = 0.001). The CNT and 4CS groups had similar milk yield (p = 0.040). The 4CS group had more lying and eating times than the CNT and 2CS groups (p = 0.000). The cortisol level in the 2CS group was 2.0 and 2.2 ㎍/dL more than the CNT and the 4CS groups, respectively (p = 0.000). Conclusion: In conclusion, the 4CS was more efficient in cooling the cows and had better welfare, as it yielded similar milk yield, and better physiological responses than the CNT despite using 90% less water.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.10a
• /
• pp.194.1-194
• /
• 2000

• Asian-Australasian Journal of Animal Sciences
• /
• v.31 no.6
• /
• pp.881-887
• /
• 2018

Objective: This study was conducted to evaluate the effects of dietary cashew nut testa (CNT) as an alternative feed ingredient to wheat bran on reproductive performance, litter performance, milk composition, and blood profiles of gestating sows. Methods: Forth multiparous sows ($Yorkshire{\times}Landrace$) were fed experimental diets starting at 35 days of pregnancy and an initial average body weight (BW) of $211.53{\pm}8.86kg$. Each sow was assigned to a treatment based on BW, backfat thickness (BF) and parity with 10 sows per treatment. Treatments were as follows: i) corn-soybean meal based diet with 6% of wheat bran (C0); ii) basal diet with 2% of CNT and 4% of wheat bran (C2); iii) basal diet with 4% of CNT and 2% of wheat bran (C4); and iv) basal diet with 6% of CNT (C6). Results: There were no statistically significant differences in BW and BF of gestating sows throughout the experimental period. However, changes in BF (p = 0.09) and the daily feed intake of sows (p = 0.09) tended to linearly increase during the lactation period. The weaning to estrus interval (WEI) showed a quadratic response to CNT treatment (p = 0.02), and the C2 diet showed the shortest WEI. Litter birth weight (p = 0.04) and piglet birth weight (p = 0.06) were linearly decreased with increase in CNT. Furthermore, there had no significant differences in piglet weight and litter weight in 21 day. Insulin concentration at day 70 of gestation was linearly reduced with increasing CNT level in diets (p = 0.03). Conclusion: When 6% CNT replaced wheat bran in gestating sow diets, there were no negative effects on sow performance, but litter birth weight and piglet birth weight were decreased when CNT level increased in gestating sow diets.

• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.422-427
• /
• 2007

Semiconducting layers are thin rubber film between electrical cable wire and insulating polymer layers having a volume resistivity of ${\sim}10^2{\Omega}cm$. Commercial semiconducting layers ire composed of polymer composites reinforced with more than 30 wt% of carbon blacks. A new semiconducting material was suggested in this study based on the carbon nanotube(CNT)-reinforced polymer nanocomposites. CNT-reinforced polymer nanocomposites were prepared by solution mixing and precipitation with various polymer type and dual filler system. The mechanical, thermal and electrical properties were investigated as a function of polymer type and dual filler system based on CNT and carbon black. The volume resistivity of composites was strongly related with the crystallinity of polymer matrix. With the decreased crystallinity, the volume resistivity decreased linearly until a critical point, and it remained constant with further decreasing the crystallinity. Dual filler system also affected the volume resistivity. The CNT-reinforced nanocomposite showed the lowest volume resistivity. When a small amount of carbon black(CB) was replaced the CNT, the crystallinity increased considerably leading to a higher volume resistivity.

• Korean Chemical Engineering Research
• /
• v.55 no.2
• /
• pp.258-263
• /
• 2017

In this study, we synthesized biocatalyst consisting of glucose oxidase (GOx), polyethyleneimine (PEI) and carbon nanotube (CNT) with addition of p-benzoquinone (BQ) that was considered anodic catalysts of enzymatic biofuel cell (EBC). For doing this, PEI/CNT supporter was bonded with BQ by physical entrapping method stemmed from electrostatic attractive force ([BQ/PEI]/CNT). In turn, GOx moiety was further immobilized on the [BQ/PEI]/CNT to form GOx/[BQ/PEI]/CNT catalyst. This catalyst has a special advantage in that the BQ that has been usually dissolved into electrolyte was immobilized on supporter. According to the electrochemical analysis, maximum current density of the GOx/[BQ/PEI]/CNT catalyst was 1.9 fold better than that of the catalyst that did not entrap BQ with the value of $34.16{\mu}A/cm^2$, verifying that catalytic activity of the catalyst was enhanced by adoption of BQ. Also, when it was used as anodic catalyst of the EBC, its maximum power density was 1.2 fold better than that of EBC using the catalyst that did not entrap BQ with the value of $0.91mW/cm^2$. Based on such results, it turned out that the GOx/[BQ/PEI]/CNT catalyst was promising and viable as anodic catalyst of EBC.

• Applied Chemistry for Engineering
• /
• v.25 no.1
• /
• pp.34-40
• /
• 2014

Mesoporous SAPO-34 catalyst was successfully synthesized by the hydrothermal method using carbon nanotube (CNT) as a secondary template. The effects of CNT contents (0.5, 1.5, 2.5, and 4.5 mol%) on catalytic performances were investigated. The synthesized catalysts were characterized with XRD, SEM, nitrogen physisorption isotherm and $NH_3$-TPD. Among the synthesized catalysts, SAPO-34 catalyst prepared by the addition of 1.5 mol% CNT (1.5C-SAPO-34) observed not only the largest amounts of mesopore volume but also acid sites. However, the mesopore volume was relatively decreased by further increasing of CNT contents due to the formation of small crystalline. The catalytic lifetime and the selectivity of light olefins ($C_2{\sim}C_4$) were examined for the dimethyl ether to olefins reaction. As a result, the 1.5C-SAPO-34 catalyst showed an improvement of ca. 36% in a catalytic lifetime and a better selectivity to light olefins as compared with the general SAPO-34 catalyst.

• Journal of Industrial Convergence
• /
• v.21 no.8
• /
• pp.35-42
• /
• 2023

Recently, electronic devices with bendable electronic devices based on flexible substrates are being sold, and therefore, the purpose of this study is to evaluate the possibility of flexible substrates of conductive transparent tapes. As a transparent electrode, carbon nanotube (CNT) was formed by the coating method developed by the research team, and samples coated up to 5 times were fabricated. The surface resistance and transmittance of the substrate were measured, and both resistance and transmittance decreased as the number of CNT coatings increased. After the tape was detached from the glass, the surface resistance slightly increased in all samples, and the transmittance increased by about 10% in all measured wavelength ranges because the glass was removed. Next, the tape coated with CNT twice was used to a bending test 20,000 times under the condition of a radius of curvature of 2 mm. The electrical and optical properties before and after bending did not change, which means that there was no change in CNT properties due to bending.