• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권4호
• /
• pp.139-143
• /
• 2005

For application of carbon nano-tube (CNT) as a counter electrode materials of dye-sensitized solar cell (DSSC), the electrochemical behavior of CNT electrode was studied, employing cyclic-voltammetry (C-V) and impedance spectroscopy. Fabrication of CNT-paste and formation of CNT-counter electrode for characteristic measurement have been carried out using ball-milling and doctor blade process, respectively. Unit cell for measurements was assembled using Pt electrode, CNT electrode, and iodine-embedded electrolyte. Field emission-scanning electron microscopy (FE-SEM) was used for structural investigation of CNT powder and electrode. Sheet resistance of electrode was measured with 4-point probe method. Electrochemical properties of electrode, C-V and impedance spectrum, were studied, employing potentiogalvanostat (EG&G 273A) and lock in amplifier (EG&G 5210). As a results, the sheet resistance of CNT electrode is almost similar to that of F-doped SnO2 (FTO) coated glass substrate as approximately 10 ohm/sq. From C-V and impedance spectroscopy measurements, it was found that CNT electrode has high reaction rate and low interface reaction resistance between CNT surface and electrolyte. These results provides that CNT electrode were superior to that of conventional Pt electrode. Particularly, the reaction rate in the CNT electrode is about thrice high than Pt electrode. Therefore. CNT electrode is to be good candidate material for counter electrode in DSSC.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.348-348
• /
• 2011

Carbon nanotube (CNT) field effect transistors and sensors use CNT as a current channel, of which the resistance varies with the gate voltage or upon molecule adsorption. Since the performance of CNT devices depends very much on the CNT/metal contact resistance, the CNT/electrode contact must be stable and the contact resistance must be small. Depending on the geometry of CNT/electrode contact, it can be categorized into the end-contact, embedded-contact (top-contact), and side-contact (bottom-contact). Because of difficulties in the sample preparation, the end-contact CNT device is seldom practiced. The embedded-contact in which CNT is embedded inside the electrode is desirable due to its rigidness and the low contact resistance. Fabrication of this structure is complicated, however, because each CNT has to be located under a high-resolution microscope and then the electrode is patterned by electron beam lithography. The side-contact is done by depositing CNT electrophoretically or by precipitating on the patterned electrode. Although this contact is fragile and the contact resistance is relatively high, the side-contact by far has been widely practiced because of its simple fabrication process. Here we introduce a simple method to embed CNT inside the electrode while taking advantage of the bottom-contact process. The idea is to utilize a eutectic material as an electrode, which melts at low temperature so that CNT is not damaged while annealing to melt the electrode to embed CNT. The lowering of CNT/Au contact resistance upon annealing at mild temperature has been reported, but the electrode in these studies did not melt and CNT laid on the surface of electrode even after annealing. In our experiment, we used a eutectic Au/Al film that melts at 250$^{\circ}C$. After depositing CNT on the electrode made of an Au/Al thin film, we annealed the sample at 250$^{\circ}C$ in air to induce eutectic melting. As a result, Au-Al alloy grains formed, under which the CNT was embedded to produce a rigid and low resistance contact. The embedded CNT contact was as strong as to tolerate the ultrasonic agitation for 90 s and the current-voltage measurement indicated that the contact resistance was lowered by a factor of 4. By performing standard fabrication process on this CNT-deposited substrate to add another pair of electrodes bridged by CNT in perpendicular direction, we could fabricate a CNT cross junction. Finally, we could conclude that the eutectic alloy electrode is valid for CNT sensors by examine the detection of Au ion which is spontaneously reduced to CNT surface. The device sustatined strong washing process and maintained its detection ability.

• Korean Chemical Engineering Research
• /
• 제61권1호
• /
• pp.52-57
• /
• 2023

본 연구는 고성능 유연 전극 소재 개발을 위한 기초 연구로, 유연 전극 소재의 성능을 향상시키기 위해 금속 산화물 CuO nanoparticles (CuO NPs)를 도입하여 탄소나노튜브 섬유(carbon nanotube fiber; CNT fiber) 표면 위에 전기화학적 증착시켜 CNT fiber/CuO NPs 전극을 합성하고, 이를 전기화학적 비효소 글루코스 센서에 적용하였다. 이 전극의 표면 및 elemental composition 분석은 주사전자 현미경(SEM)과 에너지분산형 분광분석법(EDS)을 이용하였으며, 전극의 전기화학적 특성 및 글루코스에 대한 센싱 성능은 순환전압 전류법(CV)과 전기화학 임피던스법(EIS), 시간대전류법(CA)을 통해 조사되었다. CNT fiber/CuO NPs 전극은 CNT fiber의 우수한 특성과 함께 CuO NPs 도입에 따른 약 2.6배의 유효 전극면적(active surface area) 증가 효과와 11배 정도의 향상된 전자전달(electron transfer) 특성 및 우수한 전기적 촉매 활성(electrocatalytic activity) 덕분에 CNT fiber 유연 기반 전극의 글루코스 검출에 대한 성능이 개선되었다. 따라서, 본 연구를 기반으로 다양한 나노구조체를 활용한 고성능 유연 전극 소재 개발이 기대된다.

• Korean Chemical Engineering Research
• /
• 제60권1호
• /
• pp.1-6
• /
• 2022

최근 웨어러블 디바이스에 대한 수요가 증가하면서 유연 전극 소재 개발에 대한 다양한 연구들이 진행되고 있다. 특히, 헬스케어용 웨어러블 센서들은 체온이나 심장 박동, 혈당, 혈중 산소 농도 등 신체 정보들의 실시간·지속적인 모니터링과 정확한 진단, 검출이 가능해야 하기 때문에 고성능 유연 전극 소재의 개발이 무엇보다 중요하다. 본 연구에서는 탄소나노튜브 섬유(carbon nanotube fiber; CNT fiber) 기반의 유연 전극 소재의 성능을 개선시키기 위해 CNT fiber 위에 전기화학적 중합(electrochemical polymerization) 공정을 통해 polyaniline (PANI) layer를 합성하고, 이에 대한 전기화학적 특성 분석과 비효소적 글루코스(glucose) 검출 특성을 확인하였다. 제작된 PANI/CNT fiber 전극의 표면 분석은 주사전자 현미경(SEM)을 이용하여 진행되었으며, 전극의 전기화학적 특성 및 글루코스에 대한 센싱 성능은 시간대전류법(CA)과 순환전압 전류법(CV), 전기화학 임피던스법(EIS)을 이용하여 분석되었다. PANI/CNT fiber 전극의 전기화학적 특성은 bare CNT fiber 전극에 비해 작은 electron transfer resistance와 낮은 peak separation potential, 증가된 전극 면적을 나타내며, 이런 향상된 특성들 덕분에 글루코스 검출에 대한 센싱 성능이 개선되었다. 따라서, 본 연구를 기반으로 다양한 나노구조체를 도입하고 접목을 통해 고성능 CNT fiber 기반의 유연 전극 소재 개발이 가능할 것으로 기대된다.

• Bulletin of the Korean Chemical Society
• /
• 제31권11호
• /
• pp.3123-3127
• /
• 2010

A highly sensitive electrochemical detection method for dopamine (DA) has been developed by relying on a multiwalled carbon nanotube (CNT)-sol-gel titania-Nafion composite film modified glassy carbon (GC) electrode. The CNT-titania-Nafion/GC electrode exhibited excellent electrocatalytic activity towards DA. Therefore, the CNT-titania-Nafion/GC electrode showed improved voltammetric and amperometric responses for DA compared to those obtained with both titania-Nafion/GC and Nafion/GC electrodes. The CNT-titania-Nafion/GC electrode gave a linear response ($R^2$ = 0.999) for DA from $0.5\;{\mu}M$ to 0.5 mM with a detection limit (S/N = 3) of $0.1\;{\mu}M$ and a good sensitivity of 150 mA/M while other electrodes such as CNT-Nafion/GC, titania-Nafion/GC, and a bare GC gave a sensitivity of 89, 39, and 36 mA/M, respectively. Besides, the CNT-titania-Nafion/GC electrode displayed very fast response time within 2 s. The modified electrode showed good selectivity against ascorbic acid. The modified electrode showed good stability and reproducibility. The CNT-titania-Nafion/GC electrode was applied to the determination of DA in urine and serum samples.

• 한국전기전자재료학회논문지
• /
• 제24권1호
• /
• pp.76-80
• /
• 2011

The ITO/Cabon Nano Tube (CNT) nano composites were deposited by nano cluster deposition (ITO) and arc discharge deposition (CNT) on glass substrates. The structural, optical and photovoltaic performance of ITO/CNT nano composites as a counter electrode of dye-sensitized solar-cells (DSSCs) such films were investigated. At low temperature below $250^{\circ}C$, the ITO films deposited on CNT. The ITO/CNT nano composit showed a good optical and electrical property for the counter electrode of DSSCs. When the as-prepared ITO/CNT nano composites are used for the counter electrodes, the photovoltaic parameters are $V_{OC}$ = 0.69 V, $J_{SC}$ = 5.69 mA/$cm^2$, FF = 0.32, and $\eta$ = 0.53 %. The ITO/CNT nano composites showed the possibility for the counter electrode applications of DSSCs.

• 융합정보논문지
• /
• 제12권2호
• /
• pp.127-133
• /
• 2022

ITO와 CNT를 적용한 전극을 코팅하여 제작한 대전입자형 전자종이 디스플레이 패널을 제작하여 내구성 및 전기광학적 특성을 비교한다. ITO 전극의 면저항은 10(ohm/sq.)이고 CNT 전극의 면저항은 300, 600, 1000(ohm/sq.)이며 내구성 측정을 위하여 물리적 충격 및 유연성 측정을 진행한다. ITO 전극의 경우 40회의 충격과 10mm의 곡률 반지름에서부터 변화가 시작되나 CNT 전극에서는 변화가 측정되지 않는다. 입자 이동, 반사율 및 응답 시간 측정에 필요한 구동 전압, 전계 등 전기광학 측정결과 CNT 전극은 ITO 전극과 유사한 결과를 얻었다.

• Transactions on Electrical and Electronic Materials
• /
• 제6권4호
• /
• pp.140-143
• /
• 2005

Carbon Nanotube(CNTs) counter electrode is a promising alternative to Platinum counter electrode for dye sensitized solar cells (DSSCs). In this study, CNT counter electrodes having different visible light transmittance were prepared on fluorine-doped tin oxide (FTO) glass surface by spray coating method. Microstructural images show that there are CNT-tangled region coated on FTO glass counter electrodes. Using such CNT counter electrodes and screen printed $TiO_2$ electrodes, DSSCs were assembled and its I-V characteristics have been studied and compared. Light energy conversion efficiency of DSSCs increased with decreasing in light transmittance of CNT counter electrode. Efficiency of DSSCs having CNT counter electrode is compatible to that of Pt counter electrode.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.615-616
• /
• 2005

Carbon Nanotubes (CNT) on flexible indium tin oxide (ITO) PET films were prepared for dye-sensitized solar cell (DSSC). These CNTs were prepared by spray coating method for various amount of light transparency. Also, Pt counter electrode was prepared by electro deposition method. All $TiO_2$ electrodes were deposited on ITO-PET films by spray coating method. Micro structural images show that CNT counter electrodes prepared by spray-coating have more dense structure with increasing spraying time (0 to 60 seconds). DSSC consisting of $TiO_2$ electrode and CNT counter electrode was fabricated with various amount of light absorption. DSSC have higher light energy conversion efficiency with increasing the thickness of CNT counter electrode. CNT counter electrode is at least compatible to that of CNT counter electrode.

• Korean Chemical Engineering Research
• /
• 제59권2호
• /
• pp.159-164
• /
• 2021

부착형(attachable) 타입의 웨어러블 디바이스 적용을 위한 패브릭(fabric)이나 텍스처(textiles) 타입의 고성능 전극 소재 개발에 대한 필요성이 부각되고 있다. 본 연구에서는 유연 전극 소재로 탄소나노튜브 섬유(CNT fibers)를 응용하고자, CNT fibers의 전기화학적 특성과 이를 적용한 비효소적 글루코스 센싱 성능을 확인하였다. CNT fibers의 표면 구조는 주사전자 현미경(SEM)을 이용하여 분석하였으며, 전기화학적 특성 및 센싱 성능 분석은 시간대전류법와 순환전압 전류법, 전기화학 임피던스 분석법을 이용하여 수행되었다. CNT fibers 전극은 낮은 capacitive current와 산화-환원 화학종과 전극 계면 간의 효율적인 direct electron transfer에 의한 우수한 electrochemical activity 등 향상된 전기화학적 특성으로 인해 높은 감도와 넓은 선형 농도 범위, 그리고 낮은 검출 한계 등 우수한 센싱 특성을 보였다. 따라서, 본 연구는 CNT fibers 기반의 고성능 유연 전극 소재 개발을 위한 기초 연구로 활용될 수 있을 것으로 기대된다.