• The Journal of the Korea institute of electronic communication sciences
• /
• v.3 no.2
• /
• pp.79-85
• /
• 2008

It is important to consider the life of battery and low power operation for various wireless communications. Thus, Analog current-mode signal processing with SI circuit has been taken notice of in designing the LSI for wireless communications. However, in current mode signal processsing, current memory circuit has a problem called clock-feedthrough. In this paper, we examine the connection of CMOS switch that is the common solution of clock-feedthrough and calculate the relation of width between CMOS switch for design methodology for improvement of current memory. As a result of simulation, when the width of memory MOS is 20um, ratio of input current and bias current is 0.3, the width relation in CMOS switch is obtained with $W_{Mp}=5.62W_{Mn}+1.6$, for the nMOS width of 2~6um in CMOS switch. And from the same simulation condition, it is obtained with $W_{Mp}=2.05W_{Mn}+23$ for the nMOS width of 6~10um in CMOS switch. Then the defined width relation of MOS transistor will be useful guidance in design for improvement of current memory.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2008.04a
• /
• pp.247-250
• /
• 2008

최근 무선통신용 LSI는 배터리 수명과 관련하여, 저전력 동작이 중요시되고 있다. 따라서 Digital CMOS 신호처리와 더불어 동작 가능한 SI (Switched-Current) circuit를 이용하는 Current-mode 신호처리가 주목받고 있다. 그러나 SI circuit의 기본인 Current Memory는 Charge Injection에 의한 Clock Feedthrough라는 문제점을 갖고 있기 때문에, 전류 전달에 있어서 오차를 발생시킨다. 본 논문에서는 Current Memory의 문제점인 Clock Feedthrough의 해결방안으로 CMOS Switch의 연결을 검토하였고, 0.25${\mu}m$ CMOS process에서 Memory MOS와 CMOS Switch의 Width의 관계는 simulation 결과를 통하여 확인하였으며, MOS transistor의 관계를 분명히 하여, 설게의 지침을 제공한다.

• IEIE Transactions on Smart Processing and Computing
• /
• v.3 no.6
• /
• pp.425-429
• /
• 2014

This paper proposes a DC-DC Buck-Converter with DT-CMOS (Dynamic Threshold-voltage MOSFET) Switch. The proposed circuit was evaluated and compared with a CMOS switch by both the circuit and device simulations. The DT-CMOS switch reduced the output ripple and the conduction loss through a low on-resistance. Overall, the proposed circuit showed excellent performance efficiency compared to the converter with conventional CMOS switch. The proposed circuit has switching frequency of 1.2MHz, 3.3V input voltage, 2.5V output voltage, and maximum current of 100mA. In addition, this paper proposes a SCP (Short Circuit Protection) circuit to ensure reliability.

• Journal of IKEEE
• /
• v.14 no.3
• /
• pp.232-235
• /
• 2010

A 60GHz active phase shifter with 65nm CMOS is presented by replacing passive switches in switched-line type phase shifter with active ones. Active-switch phase shifter is composed of active-switch blocks and passive delay network blocks. The active-switch phase shifter design is compact compare with the conventional vector-sum phase shifter. Active-switch blocks are designed to accomplish required input and output impedances whose requirements are different whether the switch is on or off. And passive delay network blocks are composed of lumped L,C instead of normal microstrip line to reduce the size of the circuit. An 1-bit phase shifter is fabricated by TSMC 65nm CMOS technology and measurement results present -4dB average insertion loss and 120 degree phase shift at 65GHz.

• Journal of electromagnetic engineering and science
• /
• v.8 no.3
• /
• pp.96-99
• /
• 2008

This paper describes a $0.13-{\mu}m$ CMOS RF switch for $3{\sim}5$ GHz UWB band(mode 1). It can improve isolation characteristics between ports by using deep n-well RF devices while their source and body terminals are separated. From the measurement results, the proposed T/R switch is comparative to the on-wafer probing measurement results of the series-shunt T/R switches. When the proposed T/R switch operates as Tx mode, measured insertion loss from Tx to output port is less than 1.5 dB and isolation between Tx and Rx is more than 27 dB for $3{\sim}5$ GHz. Return loss for the Tx port is more than -10 dB and input P1dB is +10 dBm.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.5
• /
• pp.261-269
• /
• 2016

A high-performance transmit/receive (T/R) switch is essential for every radio-frequency (RF) device. This paper proposes a T/R switch that is designed in the CEDEC 0.13 μm complementary metal-oxide-semiconductor (CMOS) technology for 2.4 GHz ISM-band RF applications. The switch exhibits a 1 dB insertion loss, a 28.6 dB isolation, and a 35.8 dBm power-handling capacity in the transmit mode; meanwhile, for the 1.8 V/0 V control voltages, a 1.1 dB insertion loss and a 19.4 dB isolation were exhibited with an extremely-low power dissipation of 377.14 μW in the receive mode. Besides, the variations of the insertion loss and the isolation of the switch for a temperature change from - 25℃ to 125℃ are 0.019 dB and 0.095 dB, respectively. To obtain a lucrative performance, an active inductor-based resonant circuit, body floating, a transistor W/L optimization, and an isolated CMOS structure were adopted for the switch design. Further, due to the avoidance of bulky inductors and capacitors, a very small chip size of 0.0207 mm² that is the lowest-ever reported chip area for this frequency band was achieved.

• ETRI Journal
• /
• v.30 no.4
• /
• pp.526-534
• /
• 2008

This paper presents a fully integrated 0.13 ${\mu}m$ CMOS MB-OFDM UWB transmitter chain (mode 1). The proposed transmitter consists of a low-pass filter, a variable gain amplifier, a voltage-to-current converter, an I/Q up-mixer, a differential-to-single-ended converter, a driver amplifier, and a transmit/receive (T/R) switch. The proposed T/R switch shows an insertion loss of less than 1.5 dB and a Tx/Rx port isolation of more than 27 dB over a 3 GHz to 5 GHz frequency range. All RF/analog circuits have been designed to achieve high linearity and wide bandwidth. The proposed transmitter is implemented using IBM 0.13 ${\mu}m$ CMOS technology. The fabricated transmitter shows a -3 dB bandwidth of 550 MHz at each sub-band center frequency with gain flatness less than 1.5 dB. It also shows a power gain of 0.5 dB, a maximum output power level of 0 dBm, and output IP3 of +9.3 dBm. It consumes a total of 54 mA from a 1.5 V supply.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.4
• /
• pp.116-126
• /
• 1994

In this paper, the switch-level fault simulator for CMOS circuits with a gate-to-drain/source short fault is implemented. A fault model used in this paper is based on the graphical analysis of the electrical characteristics of the faulty MOS devices and the conversion of the faulty CMOS circuit to the equivalent faulty CMOS inverter in order to find its effect on the successive stage. This technique is very simple and has the increased accuracy of the simulation. The simulation result of the faulty circuit using the implemented fault simulator is compared with the result of the SPICE simulation.

• ETRI Journal
• /
• v.27 no.5
• /
• pp.539-544
• /
• 2005

An analog CMOS vision chip for edge detection with power consumption below 20mW was designed by adopting electronic switches. An electronic switch separates the edge detection circuit into two parts; one is a logarithmic compression photocircuit, the other is a signal processing circuit for edge detection. The electronic switch controls the connection between the two circuits. When the electronic switch is OFF, it can intercept the current flow through the signal processing circuit and restrict the magnitude of the current flow below several hundred nA. The estimated power consumption of the chip, with $128{\times}128$ pixels, was below 20mW. The vision chip was designed using $0.25{\mu}m$ 1-poly 5-metal standard full custom CMOS process technology.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.1
• /
• pp.180-184
• /
• 2013

In this paper, a low power antenna switch controller IC is designed using a silicon-on-insulator (SOI) CMOS technology. To improve power handling capability and harmonic distortion performance of the antenna switch, the proposed antenna switch controller provides 3-state logic level such as +VDD, GND, and -VDD for the gate and body of switch of FETs according to decoder signal. By employing input-coupled current ring oscillator and hardware efficient level shifter, the proposed controller greatly reduces power consumption and hardware complexity. It consumes 135 ${\mu}A$ at a 2.5 V supply voltage in active mode, and occupies $1.3mm{\times}0.5mm$ in area. In addition, it shows fast start-up time of 10 ${\mu}s$.