• Elastomers and Composites
• /
• v.30 no.3
• /
• pp.235-246
• /
• 1995

When an O-ring is installed in a high fluid pressure device, a section of the O-ring is extruded into the piston-cylinder clearance gap. Any tendency towards extrusion will induce wear in dynamic applications, leading to premature failure of the seal. In this study, the mechanism of initial extrusion of the O-ring was studied, 1.e., how much amount of the O-ring will be extruded into the clearance gap at a certain pressure. The relationship between extrusion depth and a clearance gap or fluid pressure were studied by finite element analysis (FEA). After that, Salita's experimental data were analyzed. The result is that Initial extrusion depth for an O-ring into a clearance gap was 1.11 times the product of dimensionless pressure difference $(p-p_1)/E$ and clearance gap c. The required pressure $p_1$ for zero extrusion depth was found to decrease logarithmically with increasing clearance gap.

• Tribology and Lubricants
• /
• v.16 no.1
• /
• pp.27-32
• /
• 2000

This paper describes that the leaf spring damper (LSD) developed by authors can be controled by side clearance between side covers and leaf springs. The test rig and two prototype dampers with different side clearance were manufactured. Experiments were performed to investigate the effects of side clearance on the damping of the leaf spring damper. The stiffness and damping coefficients are obtained from the displacements and the reaction forces generated by rotating the eccentric shaft. All dynamic coefficients are plotted with the excitation frequency which is adjusted by rotating speed of the shaft.

• KSTLE International Journal
• /
• v.3 no.2
• /
• pp.84-89
• /
• 2002

Clearance movements of engine piston are very related to the piston impact to the engine block as well as many tribological problems. Some of the major parameters that influence these kinds of performances are piston profiles, piston offsets and clearance magnitudes. In our study, computational investigation is performed about the piston movements in the clearance between piston and cylinder liner by changing the skirt profiles and piston offsets. Our results show that curved profile and more offset magnitude to thrust side have better performance that has low side impact during the engine cycle.

• The KSFM Journal of Fluid Machinery
• /
• v.4 no.1 s.10
• /
• pp.30-37
• /
• 2001

The experimental study on the effect of axial clearance between the tip of impeller blades and stationary shroud has been performed. The investigated compressor, which is a part of a small auxiliary power unit engine, consists of a curved inlet, a centrifugal impeller, a channel diffuser and a plenum chamber. It was designed for a total pressure ratio of 4.3 and an efficiency of $77\%$ at design speed of 60,000 rpm. The experiments are carried out in an open-loop centrifugal compressor test rig driven by a turbine. For the four different clearance ratios Cr(clearance/impeller tip width) of 6.25, 10.93, 15.60 and 20.30 percent, the overall performance data are obtained at $97\%,\;90\%$ and $80\%$ of the design speed. The results show the overall pressure ratio decrease of $7.7\%$ and the efficiency loss of $8.7\%$ across the variation of clearance ratio near the design speed. It also indicates that the influence of tip clearance became weaker as the flow rate is reduced and the stable operating range is not significantly influenced by the change of clearance ratio.

• Journal of KSNVE
• /
• v.11 no.1
• /
• pp.125-131
• /
• 2001

There is a clearance between the parts of a machine due to design tolerance, manufacturing error, wear, looseness, or misalignment. If the clearance is large, the vibration and noise of the machine is generally large. Therefore, the analysis on the nitration and noise of a machine can tell the clearance of the machine, which reveals the condition of the machine, i.e., the existence of faults and the safety of the machine. The investigation of this kind of research should be on the basis of experimental results. A link mechanism with a clearance at a joint between the coupler and locker is made for the investigation of the condition monitoring of a machine due to clearance. The vibration and sound are measured from the link driving system during the operation. The signals are clarified using line enhancement technique. The noise removed signals are used to develop the dynamic model of the system for a model based fault diagnosis. Also this study showed that the clarified signals can be used for the calculation of the joint forces between the coupler and rocker and for the correlation between the vibration and sound levels and the clearance sizes.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.3
• /
• pp.189-196
• /
• 2009

The effect of inlet and outlet blade angles on a micro regenerative pump head was examined in experiments. The pump head was little increased by changing the blade angles compared with the original pump with the inlet and outlet blade angles of 0 degree. The effect of the axial clearance between the impeller and the casing on the pump head was also examined. The head was increased largely by decreasing the axial clearance. The computation of the internal flow was performed to clarify the cause of the increase of the pump head due to the decrease of the clearance. The local flow rate in the casing decreased as the leakage flow rate through the axial clearance decreased due to the decrease of the clearance. It was found that the larger head in the smaller clearance was just caused by the smaller local flow rate in the casing. In the case of the smaller clearance, the smaller local flow rate caused the smaller circumferential velocity near the front and rear sides of the impeller. This caused the increase of the angular momentum in the casing and the head.

• International Journal of Fluid Machinery and Systems
• /
• v.7 no.1
• /
• pp.28-33
• /
• 2014

In order to research the relationship between the tip clearance and leakage flow of centrifugal compressor, a high speed centrifugal compressor was investigated by using CFD. A numerical study on the effect of four different rotor tip clearance sizes of centrifugal compressor, which were 0.5times, 1 times, 1.5times and 2.0times of the design tip clearance, was carried out. Efficiency and pressure ratio curves were obtained under different mass flow. The reasons of the clearance vortex and the factors of vortex size were analyzed. The result indicated that with the increase of tip clearance size, the performance of the compressor changed obviously, the performance parameters such as efficiency and pressure ratio tended to decrease obviously. While, the leakage flow does not always lead to leak vortex. The strength of the vortex increased with the tip clearance. The size of leak vortex was affected by the pressure difference between the suction side and the pressure side of blade tip.

• Korean Journal of Environmental Biology
• /
• v.30 no.4
• /
• pp.349-354
• /
• 2012

To evaluate the biological response of sea squirt Halocynthia roretzi with different body size to heavy metals and its suitability for ecotoxicity assays, the effects of Cr, Cu and Zn on its clearance and oxygen consumption rates were investigated. Clearance and oxygen consumption rates of H. roretzi with various body sizes were calculated at different metal concentrations. Both clearance and oxygen consumption rate were negatively correlated with body sizes. Clearance rate of H. roretzi decreased gradually with increasing concentration of heavy metal, the decreasing rate was in an order of Cr>Cu>Zn. The oxygen consumption rate first increased at low metal concentration (below $100{\mu}g\;L^{-1}$) and then decreased rapidly with increasing metal concentrations. The decreasing rate was in an order of Cu>Cr=Zn. There was a trend that the clearance rate and oxygen consumption rate decreased drastically under a concentration of $400{\mu}g\;L^{-1}$, and then decreased smoothly when the metal ion concentration increased continually. So the oxygen consumption and clearance rate at a concentration of $400{\mu}g\;L^{-1}$ Cu could be thought as a suitable biological tool for exotoxicology analysis.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.40-44
• /
• 1999

A finite element analysis has been performed to investigate the effect of die clearance on shear planes in the fine blanking of a part of automobile safety belt. For the analysis S45$^{\circ}C$ is selected as an material which is used in manufacturing the part of automobile safety belt and Cockcroft-Latham fracture criterion is applied, Effect of die clearance on die-roll width die-roll depth burnish zone and fracture zone has been concentrately investigated in the finite element analysis. From the analytical results it has been found that die-roll width and depth of the shear plane increase with increasing die clearance. And the burnish zone has been concentrately investigated in the finite element analysis. From the analytical results it has been found that die-roll width and depth of the shear plane increase with increasing die clearance. and the burnish zone decreases with increasing die clearance but the variation of fracture zone is opposite to that of burnish zone because the increase in die clearance requires less fracture energy Theoretical predictions are compared with experimental results, There is a good agreement between theory and experiment

• The Korean Journal of Malacology
• /
• v.17 no.2
• /
• pp.95-104
• /
• 2001

To determine optimal conditions for measurement of the clearance rate in feeding experiment of an intertidal bivalve Glauconome chinensis, effects of starvation, extent of mixing at subsampling, and initial prey concentration were assessed. Experiments were conducted separately for each condition with different treatments. Two-way ANOVAs showed that there were significant differences in clearance rates among different starvation periods (p<0.001), extents of mixing (p = 0.005), and prey concentrations (p < 0.001). Starvation for 1 or 2 days gave rise to 2 to 3-fold increase in the clearance rate. After starvation for 5 days, the clearance rate decreased seriously, implying loss of physiological status. It is suggested that animals should be fed during acclimation. The differences of the clearance rates between gentle and vigorous mixings were significant, but the differences were smaller than that among different incubation times. It was found that vigorous mixing is not necessary. The effect of initial prey concentration was great. However, optimal prey concentration could not be determined at any fixed value. Experiments with multiple concentrations of algal prey are recommended. Optimal incubation time for measurement of the clearance rate of G. chinensis was determined to be 2-4 hours.