• Biotechnology and Bioprocess Engineering:BBE
• /
• v.9 no.2
• /
• pp.86-92
• /
• 2004

In this paper miniaturized disposable micro/nanofluidic components applicable to bio chip, chemical analyzer and biomedical monitoring system, such as blood analysis, micro dosing system and cell experiment, etc are reported. This system includes various microfluidic components including a micropump, micromixer, DNA purification chip and single-cell assay chip. For low voltage and low power operation, a surface tension-driven micropump is presented, as well as a micromixer, which was implemented using MEMS technology, for efficient liquid mixing is also introduced. As bio-reactors, DNA purification and single-cell assay devices, for the extraction of pure DNA from liquid mixture or blood and for cellular engineering or high-throughput screening, respectively, are presented.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.4
• /
• pp.45-51
• /
• 1999

In this study to assess chip breaking characteristics of cold-drawn free machining steels a newly developed non-dimensional parameter chip breaking index CB has been adopted. And for comparison with free machining steels chip breaking characteristics of conventional carbon steels were investigated. Properly controlled chips were produced with the CB value of 0.05-0.2 regardless of steel types. In case of cold-drawn free machining steels however cycle times of chip breaking are relatively shorter than those of conventional steels. And properly controlled chips were obtained from wider range of feed rate.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.319-320
• /
• 2002

Numerical simulation of chip formation during high speed machining requires knowing the friction at tool/chip interface. This parameter is hardly identified and generally the loadings (temperature, force) during the identification are not similar to those encountered during machining. Thus, Coulomb friction identified with pin-on-disc device is often used to conduct numerical simulation. The used of this technique cannot leads to good numerical results of chip formation compared to the experimental tests especially in the case of low uncut chip thickness. In this contribution, we propose a new method to evaluate the friction at tool/chip interface. In fact several Coulomb friction parameters are identified corresponding to several parts of the cutting tool. Experimental tests have been conducted allowed us to determinate both the level and the distribution of the Coulomb friction. Experimental results are also compared to the results of orthogonal cutting simulation. We show that this technique allows predicting accuracy results of chip formation.

• ETRI Journal
• /
• v.32 no.6
• /
• pp.969-971
• /
• 2010

Based on a de-embedding technique, a new method is proposed which is capable of evaluating chip impedance behavior over absorbed power in flip-chip bonded UHF radio frequency identification transponder ICs. For the de-embedding, four compact co-planar test fixtures, an equivalent circuit for the fixtures, and a parameter extraction procedure for the circuit are developed. The fixtures are designed such that the chip can absorb as much power as possible from a power source without radiating appreciable power. Experimental results show that the proposed modeling method is accurate and produces reliable chip impedance values related with absorbed power.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.2
• /
• pp.117-126
• /
• 2012

This paper provides a method for compression transmission of on-chip bus data. As the data traffic on on-chip buses is rapidly increasing with enlarged video resolutions, many video processor chips suffer from a lack of bus bandwidth and their IP cores have to wait for a longer time to get a bus grant. In multimedia data such as images and video, the adjacent data signals very often have little or no difference between them. Taking advantage of this point, this paper develops a simple bus data compression method to improve the chip performance and presents its hardware implementation. The method is applied to a Video Codec - 1 (VC-1) decoder chip and reduces the processing time of one macro-block by 13.6% and 10.3% for SD and HD videos, respectively

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.8
• /
• pp.1910-1920
• /
• 1993

An experimental study to investigate the unconventional chip formation called triangulation of chip in cutting with a SPRT (self-propelled rotary tool) is performed using acoustic emission (AE) signal analysis. In doing that, a quantitative model of the AE RMS signal in triangulation with a SPRT is first developed. The predicted results from this model show good correlation between the AE RMS signal and the general characteristics of triangular chip formation. Then, effects of various process parameters such as cutting conditions (cutting speed, depth of cut, oblique angle and normal rake angle) and the work material properties on the chip formation in cutting with a SPRT are explored. Special attention is paid to the work material properties which are found to have significant effects on triangulation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.4
• /
• pp.160-164
• /
• 2004

In DS/CDMA(direct sequence code division multiple access) system using the approximated analytic chip waveforms are applied. Proposed chip waveforms are classified into 2 types: uniform chip waveforms with uniform envelope and non-uniform chip waveforms with non-uniform envelope. It has confirmed that the similarity of the approximated analytical chip waveforms is compared using chip waveforms, envelope, phase, correlation, and bandwidth properties.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.300-304
• /
• 1993

Chip formation control is an important problem in the automation of manufacturing process, since the continuous chip can cause catastrophic failures of the tooling and entangle the workpiece causing damage. However, it is impossible to predict chip form correctly due to the complex nature of cutting process. In order to detect the chip form for unmanned manufacturing, a new identification method is proposed. The feasibility of using acoustic emission signals from the sensing plate for identification of chip form is investigated. Experiments were conducted under the various cutting conditions. When the acoustic emission sensor is attached to the sensing plate, it turns out that the moving averaged AE signals correlated well with the collision of segmented chips with the plate. The sensitivity of moving averaged AE signals to chip congestions due to continuous chip formation is illustrated as well.

• Journal of Korea Foundry Society
• /
• v.29 no.1
• /
• pp.38-44
• /
• 2009

Magnetic separation of Fe contaminated Al-Si cutting chip scraps was performed for the recyclability assessment. It was also aimed to investigate the casting and solidification characteristics of the cutting chip scraps. The magnetically separated cutting chip scraps were adequately treated for the casting procedure and test specimens were made into a stepped mold inducing different cooling rates. The test specimens were evaluated by the combined analysis of ICP, Spectroscopy, OM-image analyzer, SEM/EDS, etc. Solidification characteristics of cutting chip scraps were examined as functions of Fe content and cooling rate. It is concluded that the magnetic separation process can be utilized to recycle the Fe contaminated Al-Si cutting chip scraps in the high cooling rate foundry process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.471-474
• /
• 2001

Recently, due to demands of faster speed and extra features for the chip mounters, there has been ever-demanding needs for the basic technology. Until four or five years ago, chip mounters placing 0.3sec/chip were considered to be in the high speed category, but since then it has become a borderline for categorizing high speed machines capable of placing 0.1sec/chip. In this study, in order to analyze the vibration of head generated by the dynamic behavior of x-frame, FEM model is composed and modal analysis is performed to identify the dynamic characteristics of the structure. Those results are compared with the modal test in order to verify the model. In this paper, Several other factors, such as definition of dynamic accuracy, static accuracy and tolerance of the axis settling range, that might affect the dynamic behavior the head are discussed.