• 한국컴퓨터정보학회논문지
• /
• 제25권2호
• /
• pp.189-195
• /
• 2020

본 연구에서는 배기가스가 흡수탑으로 균일하게 유입될 수 있도록 가스 부유식 흡수탑의 입구덕트와 안내깃을 다시 설계하여 탈황효율을 높이고자 한다. 산업용 보일러에서 대기오염 물질의 주 발생원인 중에서 황산화물의 오염물질을 저감하기 위해 기존의 장치를 다시 설계하여 해결하고자 한다. 이를 위하여 가스 부유식 흡수탑 내부에서 배기가스 중에 SOx 성분의 제거효율을 높일 수 있도록 배기가스, 슬러리와 재순환 흡착제가 균일하게 접촉하도록 변경한다. 그리고 보일러 출구에서부터 가스 부유식 흡수탑 출구까지 압력손실에 대한 초기 설계값과 CFD 값을 비교하여 검증한다. 또한 배기가스의 속도분포, 재순환 흡착제 농도분포, 액상 슬러리 거동, 압력손실을 각각 비교하였다. 그 결과는 보일러 출구에서부터 흡수탑 출구까지 압력손실이 감소하고, 배기가스의 편향이 최소화되므로 인해 탈황 효율이 개선되었음을 확인하였다.

• 한국수소및신에너지학회논문집
• /
• 제31권2호
• /
• pp.169-176
• /
• 2020

There is a growing interest in hydrogen energy utilization since an alternative energy development has been demanded due to the depletion of fossil fuels. Hydrogen is produced by the reforming reaction of natural gas and biogas, and the electrolysis of water. An solid oxide electrolyte cell (SOEC) is reversible system that generates hydrogen by electrolyzing the superheated steam or producing the electricity from a fuel cell by hydrogen. If the water can be converted into steam by waste heat from other processes it is more efficient for high-temperature electrolysis to convert steam directly. The reasons are based upon the more favorable thermodynamic and electrochemical kinetic conditions for the reaction. In the present study, steam at over 180℃ and 3.4 bars generated from a boiler were converted into superheated steam at over 700℃ and 3 bars using a cylindrical steam superheater as well as the waste heat of the exhaust gas at 900℃ from a solid refuse fuel combustor. Superheated steam at over 700℃ was then supplied to a high-temperature SOEC to increase the hydrogen production efficiency of water electrolysis. Computational fluid dynamics (CFD) analysis was conducted on the effects of the number of 90° elbow connector for piping, insulation types and insulation layers of pipe on the exit temperature using a commercial Fluent simulator. For two pre-heater injection method of steam inlet and ceramic wool insulation of 100 mm thickness, the highest inlet temperature of SOEC was 744℃ at 5.9 bar.

• Journal of Biosystems Engineering
• /
• 제35권6호
• /
• pp.434-442
• /
• 2010

This study was carried out to determine necessary conditions for optimal ventilation of small windowless piglet house (4.0 (W) $\times$ 11.0 (L) $\times$ 2.6(H) m) with corridor and attic for preheating using CFD (Computational Fluid Dynamics) simulation. The experimental weaning piglet house was consisted of a corridor, an attic, 4 rooms (3.0 (W) $\times$ 2.75(L) m), 3 fences (0.7(H) m), 5 air inlets and 2 exhaust fans (0.4 (D) m) and simulated using CFD code, FLUENT. The simulation results for the experimental weaning piglet house showed that each room was uniformly ventilated under all the experimental conditions and air velocities at 0.1 m above floor are less than 0.15 m/s for 0.75 m/s and 1.0 m/s of air inlet velocity but 0.61 m/s for 1.25 m/s. The simulation results are similar to the measured results. Considering the air flow pattern, ventilating efficiency, air velocity at 0.1 m above floor and cold stress of weaning piglets and so on, the optimum velocity of air inlet might be 1.0 m/s.

• 상하수도학회지
• /
• 제20권6호
• /
• pp.911-918
• /
• 2006

This study was conducted to evaluate the effect of the launder type on settling performance and hydrodynamic behavior within the two certain full-scale sedimentation basins (each flow rate/one basin; $10,000m^3/d$); one is the transverse typed launder(existing basin) and the other is building the finger type launder in combination with the longitudinal baffle. Comparative experimental investigations have been carried out through residual turbidity and particle concentration measurements in each effluent from two basins with the transverse and the finger type launders, respectively. From the experimental results, we could observe that turbidity removal rate in the finger type launder basin (modified basin) is about 30% higher than that in the transverse type launder basin (existing basin). Also, from the measurement of total particle concentration in each effluent, the removal efficiency was improved about 27% within modified basin compared to the existing basin. In order to explain the comparative experimental results and investigate the hydridynamic behavior within each basin in more detail, we conducted computational fluid dynamics (CFD) simulation and verified simulation results with acoustic Doppler velocimetry (ADV) technique. From the CFD simulation, it was investigated that extreme upward flow occurs underneath of the transverse launder. On the other hand, in the case of modified basin, the upward flow, which occurred in the beneath of launder, was much less than that in the existing basins.

• 대한기계학회논문집B
• /
• 제41권2호
• /
• pp.109-115
• /
• 2017

전산유체해석(CFD) 기법을 이용하여 음극 지지체형 고체산화물 연료전지(SOFC)에 대한 수치해석을 수행하였다. 평판형 구조의 SOFC 에서 가스채널과 리브폭 변화에 따른 성능과 온도균일성에 관한 연구가 이루어졌다. 전산해석 툴로서는 공개소스 전산유체해석 툴박스인 OpenFOAM 을 이용하였다. 수치해석결과, 산소고갈이 일어나지 않는 범위 내에서 가스채널과 리브폭의 증가는 성능과 온도 균일성에 크게 영향을 미치지 않음을 알 수 있었다. 하지만 넓은 리브폭의 사용과 고전류밀도에서의 작동은 산소고갈로 인한 성능저하의 가능성이 있음을 확인하였다.

• Tribology and Lubricants
• /
• 제37권4호
• /
• pp.117-124
• /
• 2021

In this study, we perform a 3D CFD conjugate analysis according to the shape of the foil ramp of the air foil thrust bearing, analyze the flow characteristics inside the bearing, and compare the results corresponding to the two shapes. Air has a lower viscosity than lubricating oil. Therefore, the thrust runner of the bearing must rotate at high speed to support the load. The gap between thrust runner and foil is significantly smaller than that of the oil bearing. Hence, it is crucial to analyze the complex flow characteristics inside the bearing to predict the complex flow inside the bearing and performance of the bearing. In addition, flow characteristics may appear differently depending on the ramp shape of the bearing foil, which may affect bearing performance. In this study, we numerically analyze the main flow path of air flowing into the bearing and the secondary flow path used for cooling the bearing using the commercial CFD software ANSYS CFX and compare the flow characteristics for straight and curved foil ramp shapes. Notably, there is a difference in the speed of the flowing air according to the shape of the ramp, which affects the bearing performance.

• 한국터널지하공간학회 논문집
• /
• 제20권6호
• /
• pp.989-1002
• /
• 2018

암반 내 그라우팅은 불연속면 내부에 시멘트 그라우트재를 주입하여 주변지반을 강화하는 목적으로 사용된다. 현장에서 다상의 그라우트재의 주입 시 거동특성 및 주입경로인 3차원 절리면의 형태가 사전파악되지 않으므로 정량적인 설계가 어려운 분야중 하나이다. 따라서 현장에서의 그라우트 주입 거동특성을 나타내는 GIN (Grouting Intensity Number) 지표를 이용하여 주입 모니터링을 통해 적절한 시공관리를 수행하는 것이 최적이 방안이다. 본 논문에서는 그라우팅 주입 시 절리면의 거칠기 등급과 물시멘트(W/C)비에 따라 발생하는 압력의 손실을 전산유동해석을 수행하여 조사하였다. 절리면이 거칠수록 그리고 물시멘트비가 높을수록 주입 시 마찰저항은 크게 발생하였으며 해당 결과를 각 조건별 상관식으로 정리하였다.

• 대한조선학회논문집
• /
• 제56권3호
• /
• pp.200-210
• /
• 2019

High-speed planing craft is generally smaller than commercial vessels, for which not only the roll motion but also the pitch and heave motions are relatively large during operation However, if seakeeping performance of high-speed planing craft is evaluated by assessment methods of commercial vessels considering roll damping only, it would get unreasonable results due to excessive magnitudes of motion. This research aims at developing a procedure to evaluate seakeeping performance of high-speed planing craft reasonably well by considering responses of roll, heave and pitch motions. In addition, we tried to combine advantages of the potential flow method and CFD in this procedure, a so-called hybrid method, which uses the 3D panel method for the analysis of seakeeping performance, and tunes the damping coefficient using CFD analysis at a specific frequency. Finally, we evaluated seakeeping performance of coastal rescue boat in operation by applying the proposed procedure, and analyzed the results referring to the seakeeping criteria.

• 한국수소및신에너지학회논문집
• /
• 제32권4호
• /
• pp.228-235
• /
• 2021

Polymer electrolyte membrane fuel cells (PEMFC) are currently being used in various transport applications such as drones, unmanned aerial vehicles, and automobiles. The power required is different according to the type of use, purpose, and the conditions adjusted using a cell stack. The fuel cell stack is compressed to reduce the size and prevent fuel leakage. The unit cells that make up the cell stack are subjected to compression by clamping force, which makes geometrical changes in the porous media and it impacts on cell performance. In this study, finite elements method (FEM) and computational fluid dynamics (CFD) analysis for the deformed unit cell considering the effects of clamping force is performed. First, structural analysis using the FEM technique over the deformed gas diffusion layer (GDL) considering compression is carried out, and the resulting porosity changed in the GDL is calculated. The PEMFC model is then verified by a three-dimensional, two-phase fuel cell simulation applying the physical properties and geometry obtained before and after compression. The detailed simulation results showed different concentration distributions of fuel between the original and deformed geometry, resulting in the difference in the distribution of current density is represented at compressed GDL region with low oxygen concentration.

• 한국포장학회지
• /
• 제28권3호
• /
• pp.211-215
• /
• 2022

Air distribution occupies an important position in the smart unit load container design process for agricultural products. Inner air may be uncomfortable because of its temperature, speed, direction, and volume flow rate. It doesn't matter how efficient the ventilation equipment is if the air is not distributed well. The main aim of this study was to design the inlet and outlet fan locations of smart unit load container for agricultural products. A numerical study was performed on the effects of the location of inlet air and outlet air in relation to the container cooling sources on air distribution and thermal comfort. A concept of combining inner container cooling sources with the exhaust outlet was employed in this investigation. Also, in this research, the developed CFD (Computational Fluid Dynamics) models were thoroughly validated. This system was adopted for use in container spaces, where the exhaust outlet was located. In this study, the location of the inlet was derived through CFD for a container with a size of 1,100×1,100×1,700 mm, and it was derived that the inlet was located at the center of the lower part of the container for efficient air flow. It was efficient to position the outlet through the air inlet in the center of the lower part of the container at the top of the same side.