• Korean Journal of Remote Sensing
• /
• v.15 no.4
• /
• pp.297-305
• /
• 1999

Ocean Scanning Multispectral Imager (OSMI) is a payload on the KOMPSAT satellite to perform global ocean color monitoring for the study of biological oceanography. The instrument images the ocean surface using a wisk-broom motion with a swath width of 800km and a ground sample distance (GSD) of < 1km over the entire field of view (FOV). The instrument is designed to have an on-orbit operation duty cycle of 20% over the mission lifetime of 3 years with the functions of programmable gain/offset and on-board image data compression/storage. The instrument also performs sun and dark calibration for on-board instrument calibration. The OSMI instrument is a multi-spectral imager covering the spectral range from 400nm to 900nm using CCD Focal Plane Array (FPA). The ocean colors are monitored using 6 spectral channels that can be selected via ground commands. KOMPSAT satellite with OSMI was integrated and the satellite level environment tests including instrument aliveness/functional test, such as launch environment, on-orbit environment (Thermal/Vacuum) and EMI/EMC test were performed at KARl. Test results met the requirements and the OSMI data were collected and analyzed during each test phase. The instrument is launched on the KOMPSAT satellite on December 21,1999 and is scheduled to start collecting ocean color data in the early 2000 upon completion of on-orbit instrument checkout.

• Korean Journal of Remote Sensing
• /
• v.18 no.6
• /
• pp.337-344
• /
• 2002

In general, in order to obtain position information from satellite images, satellite sensor model which represents the geometric relationship between sensor and targeted area should be established in the first place. However, it is not simple for modelling pushbroom satellite sensor due to the image capturing process. In recent development of new generation imaging sensors, a generic sensor model, which is applicable to all types of sensors such as frame, pushbroom, whiskbroom, and SAR is in great need to the remote sensing and photogrammetry community. In this paper, the RFM as sensor model was implemented with KOMPSAT EOC and SPOT satellite images and analyzed in cases where the number and distribution of ground control points were varied. The test results of RFM were presented and compared with those of Direct Linear Transformation(DLT).

• Journal of Broadcast Engineering
• /
• v.21 no.3
• /
• pp.425-435
• /
• 2016

In this paper, we propose a classification model by analyzing raw material images recorded using a color CCD camera to automatically classify good and defective agricultural products such as rice, coffee, and green tea, and raw materials. The current classifying agricultural products mainly depends on visual selection by skilled laborers. However, classification ability may drop owing to repeated labor for a long period of time. To resolve the problems of existing human dependant commercial products, we propose a vision based automatic raw material classification combining mean shift clustering and stepwise region merging algorithm. In this paper, the image is divided into N cluster regions by applying the mean-shift clustering algorithm to the foreground map image. Second, the representative regions among the N cluster regions are selected and stepwise region-merging method is applied to integrate similar cluster regions by comparing both color and positional proximity to neighboring regions. The merged raw material objects thereby are expressed in a 2D color distribution of RG, GB, and BR. Third, a threshold is used to detect good and defective products based on color distribution ellipse for merged material objects. From the results of carrying out an experiment with diverse raw material images using the proposed method, less artificial manipulation by the user is required compared to existing clustering and commercial methods, and classification accuracy on raw materials is improved.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.21 no.2
• /
• pp.43-53
• /
• 2003

As information-communication network has been developed rapidly, internet users' circumstances also have been changed for the better, in result, more information can be applied than before. At this moment, there are many differences between real color and reappeared color on the CRT. When we observe a material object, our eyes perceive the multiplied form of light sources and nature spectral reflection. However, when the photographed signal is reappeared, illumination at that time of photographing and spectral reflection of a material object are converted into signal, and this converted RGB signal is observed on the CRT under another illumination. At this time, RGB signal is the reflected result of illumination at that time of photographing Therefore, this signal is influenced by the illumination at present, so it can be perceived another color. To accord the colro reflections of another color source, the study has been reported by S.C.Ahn$^{[1]}$, which study is about the color reapperarance system using neuron network. Furthermore, color reappearing method become independent of its circumstances has been reported by Y.Miyake$^{[2]}$. This method can make the same illuminations even if the observe circumstances are changed. To assume the light sources of observe circumstances, the study about color reappearing system using CCD sensor also have been studied by S.C.Ahn$^{[3]}$. In these studies, a population is fixed, first, on ab coordinates of CIE L${\ast}$a${\ast}$b${\ast}$. Then, color reappearing can be possible using every population and existing digital camera. However, the color is changed curvedly, not straightly, according to value's changes on the ab coordinates of CIE L${\ast}$a${\ast}$b. To solve these problems in this study, first of all, Labeling techniques are introduced. Next, basis color-it is based on Munsell color system-is divided into 10 color fields. And then, 4 special color- skin color, grass color, sky color, and gray-are added to the basis color. Finally, 14 color fields are fixed. After analyzing of the principle elements of new-defined-color fields' population, utility value and propriety value are going to be examined in 3-Band system from now on.

• Imaging Science in Dentistry
• /
• v.39 no.1
• /
• pp.35-39
• /
• 2009

Purpose: The purpose of the experiment was to evaluating the diagnostic ability of dental caries detection using digital subtraction in the artificial caries activity model. Materials and Methods: Digital radiographies of five teeth with 8 proximal surfaces were obtained by CCD sensor (Kodak RVG 6100 using a size #2). The digital radiographic images and subtraction images from artificial proximal caries were examined and interpreted. In this study, we proposed novel caries detection method which could diagnose the dental proximal caries from single digital radiographic image. Results: In artificial caries activity model, the range of lesional depth was $572-1,374{\mu}m$ and the range of lesional area was $36.95-138.52mm^2$. The lesional depth and the area were significantly increased with demineralization time (p<0.001). Furthermore, the proximal caries detection using digital subtraction radiography showed high detection rate compared to the proximal caries examination using simple digital radiograph. Conclusion: The results demonstrated that the digital subtraction radiography from single radiographic image of artificial caries was highly efficient in the detection of dental caries compared to the data from simple digital radiograph.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.10
• /
• pp.1265-1273
• /
• 1999

PIV(Particle Image Velocimetry) velocity field measurements inside the snout of a1/10 scale model of the Zn plating process were carried out at the strip speed $V_s=1.5m/s$. Aluminum powder particles ($1{\mu}m$) and atomized olive oil ($3{\mu}m$) were used as seeding particles to simulate the molten Zinc flow and deoxidization gas flow, respectively. A pulsed Nd:Yag laser and a $2K{\times}2K$ high-resolution CCD camera were synchronized for the PIV velocity field measurement. From flow visualization study, it is found that the liquid flow in the Zn pot is dominantly governed by the uprising flow caused by the rotating sink roll, with its effect on the steel strip inside the snout largely diminished by installing of the snout. The deoxidization gas flow in front of the strip inside the snout can be characterized by a large-scale vortex rotating clockwise direction formed by the moving strip. In the rear side of the strip, a counter-clockwise vortex is formed and some of the flow entrained by the moving strip impinges on the free surface of molten zinc. The liquid flow in front of the strip is governed by the flow entering the snout, caused by the spinning sink roll. Just below the free surface a counter-clockwise vortex is formed near the snout wall. The moving strip affects dominantly the flow behind the strip inside the snout, and large amount of the liquid flow follows the moving strip toward the sink roll. The thickness of the flow following the strip is very thin in the front side due to the uprising flow, however thick boundary layer is formed in the rear side of the strip. Its thickness is increased as moving downstream toward the sink roll. Inside the snout, the deoxidization gas flow above the free surface is much faster than the liquid flow in the zinc pot. Due to the larger influx of the flow following the moving strip in the rear side of the strip, higher percentage of imperfection can be anticipated on the rear surface of the strip.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.42 no.2 s.302
• /
• pp.101-112
• /
• 2005

As we perceive the world as 3-dimensional through our two eyes, we can extract 3-dimensional information from stereo images obtained from two or more cameras. Since stereo images have a large amount of data, with recent advances in digital video coding technology, efficient compression algorithms have been developed for stereo images. In order to compress stereo images and to obtain 3-D information such as depth, we find disparity vectors by using disparity estimation algorithm generally utilizing pixel differences between stereo pairs. However, it is not unusual to have stereo images having different intensity values for several reasons, such as incorrect control of the iris of each camera, disagreement of the foci of two cameras, orientation, position, and different characteristics of CCD (charge-coupled device) cameras, and so on. The intensity differences of stereo pairs often cause undesirable problems such as incorrect disparity vectors and consequent low coding efficiency. By compensating intensity differences between left and right images, we can obtain higher coding efficiency and hopefully reduce the perceptual burden of brain to combine different information incoming from two eyes. We propose several methods of intensity compensation such as local intensity compensation, global intensity compensation, and hierarchical intensity compensation as very simple and efficient preprocessing tool. Experimental results show that the proposed algerian provides significant improvement in coding efficiency.

• Journal of the Korea Concrete Institute
• /
• v.24 no.2
• /
• pp.205-214
• /
• 2012

Crack widths play an important role in the serviceability limit state. When crack widths are controlled sufficiently, the reinforcement corrosion can be reduced using only existing concrete cover thickness due to low permeability in the region of finely distributed hair-cracks. Thus, the knowledge about the tensile crack opening is essential in designing more durable concrete structures. Therefore, numerous researches related to the topic have been performed. Nevertheless accurate measurement of a crack width is not a simple task due to several reasons such as unknown potential crack formation location and crack opening damaging strain gages. In order to overcome these difficulties and measure precise crack widths, a displacement measurement system was developed using digital image correlation. Accuracy calibration tests gave an average measurement error of 0.069 pixels and a standard deviation of 0.050 pixels. Direct tensile test was performed using ultra high performance concrete specimens. Crack widths at both notched and unnotched locations were measured and compared with clip-in gages at various loading steps to obtain crack opening profile. Tensile deformation characteristics of concrete were well visualized using displacement vectors and full-field displacement contour maps. The proposed technique made it possible to measure crack widths at arbitrary locations, which is difficult with conventional gages such as clip-in gages or displacement transducers.

• Journal of the Korea Concrete Institute
• /
• v.20 no.4
• /
• pp.513-522
• /
• 2008

The fiber dispersion performance in fiber-reinforced cementitious composites is a crucial factor with respect to achieving desired mechanical performance. However, evaluation of the fiber dispersion performance in the composite PVA-ECC (Polyvinyl alcohol-Engineered Cementitious Composite) is extremely challenging because of the low contrast of PVA fibers with the cement-based matrix. In the present work, an enhanced fiber detection technique is developed and demonstrated. Using a fluorescence technique on the PVA-ECC, PVA fibers are observed as green dots in the cross-section of the composite. After capturing the fluorescence image with a Charged Couple Device (CCD) camera through a microscope. The fibers are more accurately detected by employing a series of process based on a categorization, watershed segmentation, and morphological reconstruction.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.55 no.2
• /
• pp.152-161
• /
• 2019

This research carried out a study on the job characteristics of the skipper of the coastal composite fishing vessels in order to find a way to prevent the ship collision caused by the highest human error among the marine casualty of fishing boats. Video observation was used as the research method in which six CCD cameras were installed on the vessel to collect image data and data extracted from the image were analyzed to derive the results of the functional activity of skipper according to the fishing operation process of experimental fishing vessel. The results are as follows. The working process of the experimental fishing vessel consisted of navigation for fishing ground, setting line, waiting for hauling line, hauling line and navigation to homeport. In these processes, the skipper was performing watchkeeping in the wheelhouse in which he carried out a single task, a dual task that performed two tasks simultaneously, and a triple task that performed two or more tasks simultaneously. In addition, one of the risk factors causing the collision was a no watchkeeping in the wheelhouse for navigating for fishing ground, waiting for hauling line, and hauling line at 25.4%, 64.6% and 0.3%, respectively among the marine casualty while drowsiness caused 1.2% of the marine casualty in navigating for fishing ground. Concurrent tasks that simultaneously perform two or more tasks that can overlook any other important duties while carrying out watchkeeping in the wheelhouse include 51.3% of navigation for fishing ground, 81.9% of setting line, 19.0% of waiting for hauling line, 87.9% of hauling, and 88.7% of navigation to homeport. The above concurrent tasks yielded an average of 66.1%. Experimental fishing vessels are required to focus on ship handling operations related to fishery operations, and the skipper is assigned more activities and attention to fishery related tasks. Therefore, it is considered desirable to build a collision prevention system that is appropriate to the characteristics of the skipper's work, escaping from transferring the responsibility of ship collision to the skipper completely.