• Proceedings of the KIPE Conference
• /
• 2015.11a
• /
• pp.25-26
• /
• 2015

Inductive Power Transfer (IPT) method becomes more and more popular for the Electric Vehicle (EV) battery charger due to its convenience and safety in comparison with plugged-in charger. In recent years, Lithium batteries are increasingly used in EVs and Constant Current/Constant Voltage (CC/CV) charge needs to be adopted for the high efficiency charge. However, it is not easy to design the IPT Battery Charger which can charge the battery with CC/CV charge under the wide range of load variation due to the wide range of variation in its operating frequency. This paper propose a new design and control method which makes it possible to implement the CC/CV mode charge with minimum frequency variation (less than 1kHz) during all over the charge process. A 6.6kW prototype charge has been implemented and 96.1% efficiency was achieved with 20cm air gap between the coils.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.407-408
• /
• 2017

In regenerative mode of an IPMSM control system without a bi-directional DC-DC converter, the 3-phase PWM inverter charges the battery. At this time, the regenerative torque reference for braking must output the proper torque reference to charge the battery. This paper proposed a regeneration control method that controls the voltage and current of the battery through CC-CV control at the regenerative braking torque corresponding to the driver's brake control.

• Aerospace Engineering and Technology
• /
• v.8 no.2
• /
• pp.140-148
• /
• 2009

MOV(Main Oxidizer shut-off Valves) control the combustion of launch vehicle systems by the supply and the isolation of liquid oxygen to a main combustion chamber in launch vehicle systems. Moreover, in the steady operational state, the MOV should secure a constant flow rate of liquid oxygen for combustion instability in the combustion chamber. Concerning the development of MOV, TM(Technology Model) has been manufactured and normal operations of the valve have been verified. However, the Cv of TM has been proved to be too low as compared with a design specification value. Therefore, CFD analysis have been performed by modification of the configurations of TM in order to increase sufficiently Cv of EM(Engineering Model), which is the following model of TM. The modifications of TM configurations such as partial scale-up of valve, increase of stroke length, and outlet angle of 120o would result in a considerable augmentation of Cv. It has been verified by flow capacity tests that the improved Cv of EM is min. 212, which is higher than Cv of TM, 161 by about 32%.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.2_1
• /
• pp.115-124
• /
• 2020

In wireless power transfer (WPT) system, the conventional compensation topologies only can provide a constant current (CC) or constant voltage (CV) output under their resonant conditions. It is difficult to meet the CC and CV hybrid charging requirements without any other schemes. In this study, a switching hybrid topology (SHT) is proposed for CC and CV electric vehicle (EV) battery charging. By utilizing an additional capacitor and two AC switches (ACSs), a double-side LCC (DS-LCC) and an inductor and double capacitors-series (LCC-S) topologies are combined. According to the specified CC and CV charging profile, the CC and CV charging modes can be flexibly converted by the two additional ACSs. In addition, zero phase angle (ZPA) also can be achieved in both charging modes. In this method, because the operating frequency is fixed, without using PWM control, and only a small number of devices are added, it has the benefits of low-cost, easy-controllability and high efficiency. A 3.3-kW experimental prototype is configured to verify the proposed switching hybrid charger. The maximum DC efficiencies (at 3.3-kW) of the proposed SHT is 92.58%.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.10
• /
• pp.93-100
• /
• 2013

Generally, the conventional battery charging system using an analog method has the large, heavy hardware and low efficiency. Also, it has the disadvantage that it is necessary to replace the control circuit on the basis of the characteristic curve of the specific battery cell. The proposed programmable digital LLC resonant charging system use high efficiency control system(CC-CV), and has characteristic a small hardware and advantage that a digital programming of the voltage, current, and battery capacity characteristics can be flexible. The system proposed the use of Half-bridge LLC resonant converter is possible to improve efficiency and reduce switching losses by using ZVS topology. Further, a constant voltage - constant current(CC-CV) control algorithm apply to the charger which using a buck converter. The performance of the proposed system is demonstrated through experiments.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.28 no.1
• /
• pp.30-38
• /
• 2023

In this paper, a constant current(CC) and constant voltage(CV) control method using a primary-side regulated(PSR) fly-buck converter is proposed. Because the primary-side structure of the fly-buck converter is the same as that of the synchronous buck converter, it always operates in continuous conduction mode(CCM). Therefore, in the proposed method, the load information on the secondary side can always be easily estimated by measuring the primary inductor current at the midpoint of the switch-on period. An accurate CC/CV control can be achieved through simple calculations based on this estimated information. Consequently, the proposed method is advantageous for optimizing the control performance of the PSR converter. The validity of the proposed control was verified using a 5 W prototype of a PSR fly-buck converter. The experimental results confirmed that the current reference of 500 mA was followed within the error range of 1.2%, and that the voltage reference of 12 V was followed within the error range of 1.8% despite the indirect control of the load current and output voltage from the primary side.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.23 no.2
• /
• pp.83-87
• /
• 2017

This study was conducted to determine types of oxygen transmission rate (OTR) films suitable for modified atmosphere (MA) storage treatment of strawberries (cv. 'Maehyang') for export and examination related changes in quality of strawberries during simulated shipping distribution conditions ($2^{\circ}C$ for $10days{\sim}8^{\circ}C$ for 11 days). Strawberries were packed by 1,300, 10,000, 20,000, and $30,000cc/m^2{\cdot}day{\cdot}atm$ OTR films for MA storage treatment and perforated film as the control for MAP. Fresh weight loss rate was less than 0.5% in OTR films except for the perforated film. Carbon dioxide and oxygen content in packages prevailed in permissible range for strawberries under recommended CA/MA conditions (i.e., $CO_2$: 15~20%, $O_2$: 5~10%) at 10,000 cc, 20,000 cc, and 30,000 cc OTR films. Ethylene content in OTR films did not reveal significant differences during storage. The 1,300 cc OTR film revealed highest off-flavor and lowest fungal incidence rate by sensory evaluation. The firmness, soluble solids, and visual quality were preserved the highest at 10,000 cc OTR film. In conclusion, 10,000 cc OTR film preserved the highest quality and extended shelf-life by 13 days if compared with conventional distribution conditions.

• Journal of Bio-Environment Control
• /
• v.23 no.3
• /
• pp.235-243
• /
• 2014

This research was conducted to investigate the influence of leaching fractions (LF) in each irrigation or fertigation on plant growth and changes in chemical properties of root media during the production of seedling grafts of tomato. Two root media containing Sphagnum peat moss plus vermiculite (5:5, v/v, PV) and coir dust plus vermiculite (5:5, v/v, CV) were formulated and pre-planting fertilizers were incorporated during formulation. Then, each medium was packed into 50 cell (volume 33 cc) and 105 cell (volume 18 cc) trays and the rootstock (cv. J3B Strong) and scion (cv. Sunmyung) were grown, respectively. The seedlings were grafted at 31 days after sowing and then the cut seedling grafts (Sunmyung scion/J3B Strong rootstock) were planted into 50 cell plug trays containing each of the two root media. After induction of the graft union and new adventitious roots for 7 days, the seedling grafts were fed with fertilizer solution once a week containing 4 different N concentrations (0, 50, 100, $200mg{\cdot}L^{-1}$). When determined after 31 days from seed sowing, the highest fresh weights of the root stock seedlings were obtained with 0.75 LF in PV (8.96g/seedling) and CV (7.11g/seedling) mixes. The EC of the both mixes were 0.93 and $1.09dS{\cdot}m^{-1}$, respectively. The fresh weights of the scion seedlings 31 days after seed sowing were 4.29g with 0.50 LF in the PV and 3.13g with 0.50 LF in the CV. The root medium ECs of the two treatments were 0.76 and $1.34dS{\cdot}m^{-1}$, respectively. Fresh weights of the seedling grafts grown for 31 days were greatly influenced by post-planting fertilizer concentrations. The heavier plants were obtained in $100mg{\cdot}L^{-1}$ N treatment than any other treatments in same mixes. The substrate ECs in these two treatments were 0.98 and $1.93dS{\cdot}m^{-1}$, respectively, indicating that the desirable range of soluble salts in soil extracts is higher in the CV mix than the PV mix. Results of this study suggest that optimum EC range is different in each medium and LF need to be adjusted differently for each root medium to produce high quality seedling grafts of tomato.

• Journal of Bio-Environment Control
• /
• v.20 no.3
• /
• pp.221-226
• /
• 2011

The study was carried out to investigate the effect of MA packaging materials on quality and storability of tomato in long distance export condition. We found that the fresh weight loss in perforated film was higher than other breathable films. The fresh weight of tomato (cv 'Madison') packaged with breathable films, such as 5,000 cc, 10,000 cc, $20,000cc/m^2{\cdot}day{\cdot}atm$ oxygen permeable films, reduced less than 0.6%, but perforated film that already being used for packaging horticultural crops showed 1.4% fresh weight loss during $5^{\circ}C$ storage for 20 days and then $20^{\circ}C$ storage for last 5 days with 85% relative humidity. The carbon dioxide and oxygen concentration in tomato packages showed proper level for MA storage in $20,000cc/m^2{\cdot}day{\cdot}atm$ $O_2$ breathable film treatment at $5^{\circ}C$ storage. Although at $20^{\circ}C$ storage, the carbon dioxide concentration increased sharply, the oxygen concentration decreased remarkably, the change of these gases concentration was the lowest in 20,000 cc film treatment. The ethylene concentration was sharply increased at $20^{\circ}C$ from $21^{st}$ day to $25^{th}$ day after $5^{\circ}C$ storage for 20 day, and the concentration was lower in 20,000 cc film treatment among the breathable film treatments. Until 20 days, at $5^{\circ}C$ storage all treatments did not exceed the marketability. However, the last 5 days during at $20^{\circ}C$, the fruit appeared fungal rots and the quality rapidly decreased. The $20,000cc/m^2{\cdot}day{\cdot}atm$ $O_2$ permeability treated tomato performed higher firmness (9.56 N), vitamin C (16.31 mg/100 gFW), and soluble solids ($7^{\circ}Brix$) than other breathable films at final storage day. The results suggest that the $20,000cc/m^2{\cdot}day{\cdot}atm$ $O_2$ permeable film treatment of tomato (cv 'Madison') performed the highest quality and storability of tomato for long distance exporting.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1991.10a
• /
• pp.332-347
• /
• 1991

Accurate prediction of future settlement is essential for the settlement control of soft soil by pre-loading method. To predict future settlement in clayey soft soils, several methods like Asaoka method, Hyperbolic Method and Hoshino method are currently being used. These methods predict the future sett1ement by mathmatical treatment of the measured settlement data on the basis of consolidtion theory and empiricism. But the correlation coefficient between the measured and the predicted settlement was relatively low (0.8~0.9). Also, the prediction of future settlemet for the design load is very difficult. In this article, the measured field settlement data was treated as the the field consolidation test. Hence, condolidation coefficient(Cv) and compression index(Cc) was evaluated from the field settlement data. Cv and Cc values from field data was used to calculate the degree of consolidation and settlement at desired time. By this method, the correlation coefficent between the measured and the predicted settlement was significantly increased(0.97~0.99). Also the settlement by the design load after the improvement of soft soil could be predicted reasonably. This method is quite rational and sound but it requires thousands of calculation steps. Today, by the aid of low priced personal computers above mentioned technique could be used much acre economically and effectively than conventional methods. This article presented the mechanisms and capacities of this method and demonstrated the enhanced correlation coefficient when applied to actual field settlement data.