• 한국생산제조학회지
• /
• 제9권2호
• /
• pp.138-143
• /
• 2000

The establishment of a practical ultra-precision grinding technique using Diamond and CBN wheels is one of the major key technolo-gies to improve production techniques for machine-to-difficult materials without finishing process such as lapping and polishing. But the special efficient dressing technique for ultra-fine grit type grinding wheels to stabilize the grinding ability was not developed. Recently electrolytic in-process dressing technique is proposed to ultra-fine grit type metal bonded diamond wheels to protrude abra-sives continuously from the tool surface. This technology can be widely used to surface grinding and cylindrical grinding but cannot be used efficiently to internal grinding because of the electrode attachment trouble. This paper describes the effect of interval type electrolytic dressing as proposed newly to cast iron bonded diamond wheel for efficient internal grinding with mirror type high quality ground surface.

• 한국기계가공학회지
• /
• 제1권1호
• /
• pp.101-108
• /
• 2002

In the grinding process, the degree of the sharpness in wheel gram affects the surface roughness and the dimensional accuracy. If a wheel with dull grains is used, the grinding force will be increased and the surface roughness deteriorated. To produce a precision component, the magnitude of parameters related to the wear amount of a grinding wheel has to be limited. In this study, a variation of the grinding force and the surface roughness were measured to seek the machining characteristics of the W A and CBN wheels. From the wear amount of the grinding wheel and the removal rate of workpiece, the grinding ratio was calculated. And also the wheel life was determined at a rapid decreasing point of the grinding ratio. The difference between the surface of wheel-workpiece before grinding and after wheel life was clearly verified with a microscopic photo.

• 한국기계가공학회지
• /
• 제15권1호
• /
• pp.68-73
• /
• 2016

In this paper, the grinding characteristics in internal grinding methods(plunge, thrust) were studied with vitreous CBN wheels using machining center. Grinding experiments were performed according to the same material removal rate conditions such as a wheel speed, depth of cut and workpiece speed. And the grinding force, machining error and grinding ratio were investigated though these experiments. Based on the experimental results, the grinding characteristics on internal grinding methods were compared.

• 한국공작기계학회논문집
• /
• 제16권2호
• /
• pp.30-36
• /
• 2007

In order to estimate the maximum undeformed chip thickness in grinding operation, it is necessary to obtain the successive cutting point spacing. In the past it was obtained by experiments. In this paper, the average successive cutting point spacing has been obtained using the given grinding input conditions and it is possible to estimate the maximum undeformed chip thickness without using any experimentally obtained data. The validity of the proposed analysis has been verified based on two sets of grinding scratch tests using WA and CBN grinding wheels.

• 한국기계가공학회지
• /
• 제14권4호
• /
• pp.55-61
• /
• 2015

In this paper, the grinding characteristics of internal thrust grinding were studied with vitreous CBN wheels using a machining center. Grinding experiments were performed according to grinding conditions, such as wheel feed speed and depth of cut, workpiece speed, and rate of grinding width. Additionally, the grinding force and grinding ratio were investigated though these experiments. Based on the experimental results, the grinding characteristics of internal thrust grinding were discussed.

• 한국기계가공학회지
• /
• 제15권5호
• /
• pp.73-79
• /
• 2016

In this paper, the grinding characteristics in thrust internal grinding have been studied using vitreous CBN wheels with a machining center. Grinding experiments have been performed according to grinding conditions such as wheel feed speed, cut depth, workpiece speed, rate of grinding width and number of grinding passes. The machining error, shape of machined surfaces, grinding force, and surface roughness have been investigated though these experiments. Based on the experimental results, the grinding characteristics on the machined surface in the internal thrust grinding are discussed.

• 한국정밀공학회지
• /
• 제19권3호
• /
• pp.59-65
• /
• 2002

In the grinding process, the degree of the sharpness in wheel grain affects the surface roughness and the dimensional accuracy. If a wheel with dull grains is used, te grinding force will be increased and the surface roughness deteriorated. To produce a precision component, the magnitude of parameters related to the wear amount of a grinding wheel has to be limited. In this study, a variation of the grinding force and the surface roughness were measured to seek the machining characteristics of the WA and CBN wheels. From the wear amount of the grinding wheel and the removal rate of workpiece, the grinding ratio was calculated. And also the wheel life was determined at a rapid decreasing point of the grinding ratio. The difference between the surface of wheel-workpiece before grinding and after wheel life was clearly verified with a microscopic photo.