• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.4
• /
• pp.40-45
• /
• 2003

In this paper, to choose the optimum CBN wheel for Internal Grinding at LM Guide, among 7 types of CBN-wheels, the 2 types of CBN-wheels, which were the macrofracture CBN wheel and the microfracture CBN wheel, have been used, and the SCM420H have been used as the workpiece. The working conditions in the grinding experiments were depth-of-cut, table speed, and spindle speed for 4 types of the CBN grinding wheels, 2 types of the lubrications. By the experiments, the loading effect of the microfracture types of the CBN-wheel needed a short dressing interval and resulted in grinding wheel wear and bad surface roughness. However, a macrofracture type of CBN-wheel with the concentration of 100, CB120Q100V showed the best surface roughness quality at a low table speed for internal grinding at LM-guide.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.3
• /
• pp.31-37
• /
• 2011

The purpose of this study is to investigate cutting characteristics and wear behavior in SCM440 steel with different cutting tools, CBN(Cubic Boron Nitride) and coated CBN. During the test coated CBN tool especially with TiAlN showed better wear resistance behavior than orginal CBN tools. In the interrupted cutting condition, axial groove affected tool surface with impact force during the turning operation. For advantageous turning parameter in the interrupted process it is recommendable that lower speed. Also surface roughness showed better behavior in the coated CBN tool conditions than normal CBN conditions. Mainly this is caused by reduced friction between material and tool surface with coated layer.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1533-1541
• /
• 1990

Cubic boron nitride (CBN) is known the second hardest material followed diamond and was provided industry as an abrasive grain in the late 1960's. Since the introduction of CBN, a large amount of research has been carried out to determine the best application condition for grinding operation. Despite the advantages in its characteristics, CBN has not yet gained full acceptance as more excellent abrasive grain than traditional one. The reason for this state is that the surface roughness ground by CBN is worse than by traditional one and dressing and truing is very difficult. This led user's resistance to the use of CBN as an abrasive grain. Present study is to investigate the cause of lower surface roughness ground by CBN single crystal abrasive grain comparing with traditional one.

• Journal of the Korean Society of Industry Convergence
• /
• v.8 no.4
• /
• pp.227-234
• /
• 2005

In this study an experimental investigation was conducted to assesment of cutting ability for CBN ball end-milling, STD11 and NAK80 materials. The cutting force and surface roughness of the work-pieces were obtained in machining center. The assessment of CBN tools were inspected through the tool dynamotor and SEM. When $30^{\circ}$ negative rake angle, the wear and cutting force were good, surface roughness was better at cutting fluid during CBN cutting.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.315-320
• /
• 2001

Ultra-abrasives such as diamond and CBN have used to maintain accuracy and form deviation for superalloy etc. This study contains the dry cylindrical grinding of metals with Vitrified-bond CBN wheel and Resinoid-bond CBN wheel. For various condition of grinding speed, workpiece speed, grinding depth and feed speed of table, the grinding resistance, the surface roughness, and material removal are measured and discussed.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.7
• /
• pp.58-65
• /
• 1999

Hard turning offers many possible benefits over grinding such as lower equipment costs, shorter setup time, reduced process steps and better surface integrity. Despite the amount of research in this area, there exists no data in the intermittent hard turning. The objective of this paper is to investigate the effect of CBN tool materials and machinability to an intermittent hard turning. To this end, different CBN materials were tested to evaluate the tool wear and surface roughness in an intermittent hard turning. It is found that low-CBN-content tool is better than high-CBN-content tool. Then, we discussed a cutting force, vibration, and CBN tool wear mechanism from the hard turning.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.12
• /
• pp.121-126
• /
• 1997

The use of CBN tool material has been greatly increased because of the superior metal cutting performance for the machining of hardened steel. This paper presents some experimental results on the ball endmiling of harened steels. Three different hardnesses of STD11 workpieces were machined using CBN ball endimills, and the machining characteristics including cutting forces tool wear, and surface roughness of machined surface were compared. It has been found that the CBN ball endmill works better in the machining of harder workpieces. The microscopic examination explains that this unusual phenomenon is caused by the difference of microstructure of each workpieces.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.26-30
• /
• 1996

This paper presents the performance of CBN tools in the machining of hardened die-materials, SKD11 and SKD61 steel with HRC 50, by high-speed face milling. Generally, grinding or EDM is being used in machining of hardened materials but the cost is very high. If those can be replaced by cutting, it will be a greatly economical advantage. CBN tool has been recognized as an effective tool in turning, but it has not been in milling. So wear and surface roughness mode of CBN tool for hardened SKD11 and SKD61 steel were investigated by high-speed face milling in this study Also the relation between cutting force and wear mode of CBN tools was investigated.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.5
• /
• pp.25-30
• /
• 2001

The purpose of this investigation is experimentally to clarify the machinability and optimum tool geometry on milling of hardened STD11 steel. In the finish process office milling of high hardened STD11 steel by CBN tool, the optimum tool shape is suggested, which can minimize the tool fracture and chipping by impact. It is measured that cutting farce, tool wear and surface roughness generated during single-insert face milling using various geometric CBN tools. It has been found that the optimal chamfer angle of CBN tool is about -$25^{\circ}C$ and the suitable chandler width is 0.2mm. The nose radius of tool is the most excellent at 1.2mm in the viewpoint of tool wear and surface roughness.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.925-929
• /
• 2001

Ultra-abrasives such as diamond and CBN have used to maintain accuracy and form deviation for superalloy etc. This study contains the dry cylindrical grinding of metals with Vitrified-bond CBN wheel and Resinoid-bond CBN wheel. For various conditions of grinding speed, workpiece speed, grinding depth and feed speed of table, the grinding resistance, the surface roughness, and the material removal are measured and discussed.