• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.108-113
• /
• 2004

The compressive axial collapse tests were performed to investigate energy absorption characteristics of Al/CFRP compound tubes which are aluminum tubes wrapped with CFRP (Carbon Fiber Reinforced Plastics) outside the aluminum circular and square tubes. Based on collapse characteristics of aluminum tubes and CFRP tubes respectively, the axial collapse tests were performed for Al/CFRP compound tubes which have different fiber orientation angles. Test results showed that Al/CFRP compound tubes supplemented the unstable brittle failure of CFRP tubes due to ductile nature of inner aluminum tubes. In the light-weight aspect, specific energy absorption were the highest for Al/CFRP, CFRP in the middle, and aluminum the lowest. Also, specific energy absorption of circular tubes was higher than square tubes'. It turned out that fiber orientation angle of Al/CFRP compound tubes influence specific energy absorption together with the collapse modes of the tubes.

• 대한기계학회논문집A
• /
• 제30권12호
• /
• pp.1603-1610
• /
• 2006

In this paper compressive characteristics of composite egg-box panels were investigated and energy absorption was calculated from the nominal stress-strain relations obtained by the compressive tests. Several different stacking sequences and number of plies were introduced for investigation of static compression characteristics and the energy absorption rates of composite egg-box panels. The compressive stress-strain relation and energy absorption of various composite egg-box panels were compared with those of aluminium egg-box panels. From the test results it was found that the fracture behavior of composite egg-box panel was affected by stacking angle causing different local deformation, during lay-up and draping processes and types of prepreg; that is, plain weave carbon/epoxy and 4-harness satin glass/epoxy. The energy absorption capacity of composite egg-box panels were proved to be higher than that of aluminium egg-box panels with low mass.

• 비파괴검사학회지
• /
• 제36권3호
• /
• pp.175-180
• /
• 2016

Nondestructive evaluation for material health monitoring is important in aerospace industries. Composite laminates are exposed to heat cyclic loading and humid environment depending on flight conditions. Cyclic heat loading and moisture absorption may lead to material degradation such as matrix breaking, debonding, and delamination. In this paper, the moisture absorption ratio was investigated by measuring the Lamb wave velocity. The composite laminates were manufactured and subjected to different thermal aging cycles and moisture absorption. For various conditions of these cycles, not only changes in weight and also ultrasonic wave velocity were measured, and the Lamb wave velocity at various levels of moisture on a carbon-epoxy plate was investigated. Results from the experiment show a linear correlation between moisture absorption ratio and Lamb wave velocity at different thermal fatigue stages. The presented method can be applied as an alternative solution in the online monitoring of composite laminate moisture levels in commercial flights.

• 한국막학회:학술대회논문집
• /
• 한국막학회 2004년도 추계 총회 및 학술발표회
• /
• pp.216-219
• /
• 2004

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2008년도 Asian Magnetics Conference
• /
• pp.144.1-144.1
• /
• 2008

• Composites Research
• /
• 제22권6호
• /
• pp.32-38
• /
• 2009

본 연구에서는 탄소, 케블라 및 탄소-케블라 하이브리드 등 4가지 소재로 제작된 원형튜브시편에 대한 에너지 흡수능력 및 파손모드를 평가하였다. 이를 위해, 본 연구에서 일방향 프리프레그를 이용해서 원형튜브 제작하고 10mm/min의 하중속도로 준정적 압축시험을 수행하였다. 시험을 통해 취성파괴모드로 압축되는 탄소/에폭시로 제작된 튜브가 가장 우수한 에너지 흡수 특성을 보인 반면, 좌굴에 의해 압축되는 케블라/에폭시 튜브가 가장 낮은 에너지 흡수특성을 보였다. 하이브리드 [$90_C/0_K$]튜브의 경우 국부좌굴모드에 의해 에너지를 흡수했으며 우수한 압축후 구조온전성 특성을 보였다. [$90_K/0_C$] 튜브의 경우 주 파손모드는 단층굽힘모드이고 압축후 구조온전성이 확보되지 못했다.

• 펄프종이기술
• /
• 제48권2호
• /
• pp.20-27
• /
• 2016

Ethylene gas is a natural hormone that directly affects the freshness of agricultural products, so it is very important for the maintenance of freshness to remove ethylene gas from corrugated board boxes. Many methods for the removal of this and other gases have been reported. In this study, the utilization of an absorbent using activated carbon was adopted for the removal of ethylene gas from a corrugated board box. Activated carbon powders were prepared by grinding in a laboratory and were used to treat the surface and to laminate paperboards with a starch solution. The ethylene gas absorption was evaluated by using a gas chromatography to measure the residual ethylene gas concentration. About 60% of the ethylene gas was absorbed by the activated carbon itself. However, the paperboards that were surface-treated and laminated with starch and activated carbon showed lower than 20% ethylene gas absorption. This was because the starch and smaller particles of activated carbon blocked the surface pores of activated carbon particles. Therefore, either the use of the binders must be minimized for the surface treatment of paperboards, or activated carbon packs can be used as absorbents in corrugated boxes.

• 상하수도학회지
• /
• 제37권6호
• /
• pp.335-345
• /
• 2023

In Korea, as part of the Green New Deal project toward a carbon-neutral society, it is necessary to build a climate-resilient urban environment to green the city, space, and living infrastructure. To this end, SWMM-ING was improved and the model was modified to analyze the carbon reduction effect. In addition, I plan to select target watersheds where urbanization is rapidly progressing and evaluate runoff, non-point pollution, and carbon reduction effects to conduct cost estimation and optimal design review for domestic rainwater circulation green infrastructure. In this study, green infrastructure facilities were selected using SWMM-ING. Various scenarios were presented considering the surface area and annual cost of each green infrastructure facility, and The results show that the scenario derived through the APL2 method was selected as the optimal scenario. In this optimal scenario, a total facility area of 190,517.5 m² was applied to 7 out of 30 subwatersheds to achieve the target reduction. The target reduction amount was calculated a 23.50 % reduction in runoff and a 26.99 % reduction in pollutant load. Additionally, the annual carbon absorption was analyzed and found to be 385,521 kg/year. I aim to achieve additional carbon reduction effects by achieving the goal of reducing runoff and non-point pollution sources and analyzing annual carbon absorption. Moreover, considering the scale-up of these interventions across the basin, it is believed that an objective assessment of economic viability can be conducted.

• 한국항해항만학회지
• /
• 제30권9호
• /
• pp.763-766
• /
• 2006

In this paper, the EM wave absorbers were designed and fabricated for X -band sensors using Carbon of dielectric material with CPE. The complex relative permittivity of samples is calculated by using measurement results of S-parameter. We simulated the double-layered type EM wave absorber with broad bandwidth using the measured complex relative permittivity by changing the thickness and layer, which was fabricated based on the simulated design The fabricated EM wave absorber consists of 1 mm first layer sheet facing metal with Carbon composition ratio 70 vol. % and 1.5 mm second layer sheet with Carbon composition ratio 60 vol. %. The measured results showed a good agreement to the simulated ones. It is found toot the optimized absorption ability of double-layered type EM wave absorber with thickness of 2.5 mm is higher than 10 dB from 7.8 GHz to 13.3 GHz.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2006년도 International Symposium on GPS/GNSS Vol.1
• /
• pp.297-300
• /
• 2006

In this paper, the EM wave absorbers were designed and fabricated for X-band sensors using Carbon of dielectric material with CPE. The complex relative permittivity of samples is calculated by the measured S-parameter data. We simulated the double-layered type EM wave absorber with broad bandwidth using the measured complex relative permittivity by changing the thickness and layer, which was fabricated based on the simulated design. The fabricated EM wave absorber consist of 1mm first layer sheet facing metal with Carbon composition ratio 70 vol% and 1.5 mm second layer sheet with Carbon composition ratio 60 vol%. The comparisons of simulated and measured results are good agreement. As a result, the optimized absorption ability of double-layered type EM wave absorber with thickness of 2.5 mm is higher than 10 dB from 7.8 GHz to 13.3 GHz.