• Journal of the Korean Ceramic Society
• /
• v.30 no.1
• /
• pp.7-16
• /
• 1993

Effect of sulfate on the reactionof C3S formation in presence of clinker melt and its appearance in clinker were investigated, using (NH4)2SO4 and CaSO4 as sulfate sources. When (NH4)2SO4 and CaSO4 were added, both showed the similar results, 1.0wt% of sulfate could promoted the reaction of C3S formation, however for its content of more than 2.0wt%, the formation of C3S was prevented. Residual limit of sulfate to C3S formation is about 1.4wt%. Appearances of sulfate were C4A3l and CaSO4 in interstitial phase. For the addition of (NH4)2SO4 or CaSO4 of 20wt%~4.0wt%, C3S grains showed the hypertrophic growth. We might consider that, because sulfate reduced the surface tension and viscosity of the clinker melt, C3S crystals were precipitated below 140$0^{\circ}C$, and the crystlas of C3S were coalesced and linked in the same crystallographical direction with increasing temperature becuase of their rapid growth rate.

• Journal of the Korean Ceramic Society
• /
• v.27 no.2
• /
• pp.195-200
• /
• 1990

For the development of low energy cement, the belite cement clinker of calcium sulphoaluminate ferrite type was synthesized at 130$0^{\circ}C$ and containing C2S, C4A3S as the major minerals along with C3A, C4AF, CS by using limestone, dolomite, clay, iron ore, gypsum and alumina as raw materials. At over 130$0^{\circ}C$, C4A3S was decomposed and thus C3A was increased. When hydrated, this cement was hardened, producing ettringite, CSH, etc.

• Journal of the Korean Ceramic Society
• /
• v.27 no.8
• /
• pp.1055-1063
• /
• 1990

The early hydration characteristics of the system $C_3S-C_3A-C_4AF$ according to the clinker composition variations, in order to establish the mutual interactionof clinker minerals during the portland cement hydration, have been studied. The early hydration rate of $C_3S$ was greatly effected by the change of $C_3S/C_3A$ ratio. The lower the $C_3S/C_3A$ ratio was, the faster the apex reaching time and the rate of heat liberation of the 2nd exothermic peak originating from the formation of $Ca(OH)_2$ were. The effect of $C_3S/C_3A$ ration on the amounts of $Ca(OH)_2$ formation was decreased, in process of hydration time, but the effect of $C_3S$ content was increased.

• Cement
• /
• s.66
• /
• pp.12-15
• /
• 1977

석회석과 고로수재 slag을 1.6 : 1로 혼합 분쇄한 원료를 1,450$^{\circ}C$에서 소결하여 고$C_3A$ clinker를 얻었다. 이 clinker 중에는 $C_3S$ 40$\%$, $C_2S$ 31$\%$, $C_3A$ 22$\%$, $C_4AF$ 2$\%$를 함유하고 있으며 보통 크링카 보다 $C_3A$ 함량이 2$\~$3배 정도 높고, clinker 색은 연두색을 띄는 것이 특색이다. 이와 같이 $C_3A$ 함량이 높은 시멘트의 특성 및 제조 가능성을 검토한 결과는 다음과 같다. 1) 석회석과 slag를 1.6 : 1(61.5$\%$ : 38.5$\%$)로 사용할 경우 보통 시멘트 제조시 석회석 사용량 보다 약 28$\%$ 정도 절감되나 고품위의 석회석이 요구된다. 2) 동일 free CaO 0.4$\%$를 기준으로 소성할 경우 고$C_3A$ clinker가 보통 clinker 보다 소성 시간이 20분 단축된다. 3) carbonate 분해열을 비교하면 고$C_3A$ 시멘트 원료가 보통 시멘트 원료보다 116Kcal/$\cal{kg}$-cl 절감된다. 4) $C_3A$ 함량이 높아 가소성이 저하되고 표준연도의 시멘트 paste를 얻기 위하여서는 보통 시멘트 보다 많은 물량이 요구되며 응결시간도 빠르다. 5) Blaine 3,000$cm^3$/g으로 분쇄한 고$C_3A$ 시멘트의 3 일강도는 보통 시멘트 보다 40$\~$50$\cal{kg}$/$cm^3$ 더 높으나 28 일 강도는 다소 저하되는 경향이며 Blaine 5,000$cm^2$/g으로 분쇄한 고$C_3A$ 시멘트는 조강 시멘트와 같은 강도 수준이다.

• Journal of the Korean Ceramic Society
• /
• v.37 no.5
• /
• pp.459-465
• /
• 2000

3CaO.3Al2O3.CaSO4(C4A3)clinker was prepared by solid state reaction and then its hydration property was investigated. C4A3 clinker was fired at various temperatures in the range of 700~135$0^{\circ}C$. The hydration of it was studied by XRD, DSC, Solid-state 27Al MAS NMR and SEM. According to the results, the Ca4A3 clinker was produced by reacting calcium aluminates with CaSO4 and Al2O3 and C4A3 was formed as a main phase after calcining at 120$0^{\circ}C$. The hydration products were mainly calcium monosulfoaluminate hydrate and Al(OH)3, and they were produced after 2hrs of hydration. However the hydration rate was about 74% at 3days.

• Journal of the Korean Ceramic Society
• /
• v.33 no.10
• /
• pp.1163-1169
• /
• 1996

The effects of borax on the phase formation of C2S, C4A3 and $\alpha$'-C2S phases. It has negative effects on formation of C4A3 And it lowers the forming temperature of C4AF. It also has been found that borax improves the clinkerization of MBC. In the MBC clinker with borax 3% C2S have larger and more irregular shapes, larger C/S mole ratio and C4A3 have smaller size larger C/ molr ratio than in the clinker without borax.

• Journal of the Korean Ceramic Society
• /
• v.22 no.2
• /
• pp.33-38
• /
• 1985

The hydration of supersulphated slag cement which is the mixture of granuloated blast furnace slag anhydrite $C_4A_3$ type clinker and calcined dolomite was studied by X-ray diffraction differential thermal analysis scanning electron microscope observation and measurement of the rate of heat liberation. The main hydrates were ettrigite and C-S-H. This supersulphated slag cement enhanced rapid-hardening and increased in strength at early stage due to the much of ettrigite. Furthermore the hardened cement became stronger due to the C-S-H that was produced from the hydration of the $eta$-$C_2S$ in $C_4A_3$ type clinker and the hydration of the dissolved components from slag at later period.

• Journal of the Korean Ceramic Society
• /
• v.17 no.4
• /
• pp.217-221
• /
• 1980

Hydration of granulated blastfurnace slag-gypsum-$C_4A_3\bar{S}$ clinker/modified converter slag clinker was investigated to develop the cement of slag-gypsum system. In the hydration of granulated slag-gypsum-$C_4A_3\bar{S}$ system clinker, the hydrates such as ettringite, CSH gel and $AH_3$ gel were formed, and the strength of hardened body would be increased by forming compact microstructure. The modified converter slag clinker which contains alite and calcium aluminate was synthesized, and the hydration reactivity of the cement from this clinker, gypsum and granulated slag is similar to usual portland cement, and the hydrates were mainly CSH, ettringite, and $Ca(OH)_2$.

• Computers and Concrete
• /
• v.15 no.1
• /
• pp.89-101
• /
• 2015

In this paper, Artificial Neural Networks (ANN) and Multiple Linear Regression (MLR) models were discussed to determine the compressive strength of clinker mortars cured for 1, 2, 7 and 28 days. In the experimental stage, 1288 mortar samples were produced from 322 different clinker specimens and compressive strength tests were performed on these samples. Chemical properties of the clinker samples were also determined. In the modeling stage, these experimental results were used to construct the models. In the models tricalcium silicate ($C_3S$), dicalcium silicate ($C_2S$), tricalcium aluminate ($C_3A$), tetracalcium alumina ferrite ($C_4AF$), blaine values, specific gravity and age of samples were used as inputs and the compressive strength of clinker samples was used as output. The approximate reasoning ability of the models compared using some statistical parameters. As a result, ANN has shown satisfying relation with experimental results and suggests an alternative approach to evaluate compressive strength estimation of clinker mortars using related inputs. Furthermore MLR model showed a poor ability to predict.

• Journal of the Korean Ceramic Society
• /
• v.40 no.8
• /
• pp.804-810
• /
• 2003

The fine powder produced by heating and grinding of the waste concrete in the waste construction was investigated whether utilize as substitution raw material of SiO$_2$, CaO, and Al$_2$O$_3$ source for OPC clinker manufacture is possible or not. In order to synthesize OPC clinker, limestone, shale, converter slag and fly ash were used as main raw materials, and modulus was fixed LSF 91.0, SM 2.60, IM 1.60. The synthesized clinkers were characterized. The Main products of synthesized clinker were C$_3$S, ${\beta}$-C$_2$S, C$_3$A, C$_4$AF as OPC clinker at 1,43$^{\circ}C$. As a result of TG-DTA and burnability index(B.U) analysis of each raw mixtures, the formation temperature of clinker phases was similar and B.I was showed easy burning as 48.6∼51.4.