• Journal of the Korea Concrete Institute
• /
• v.29 no.1
• /
• pp.65-75
• /
• 2017

C-S-H phase is the most abundant reaction product, occupying about 50~60% of cement paste volume. The phase is also responsible for most of engineering properties of cement paste. This is not because it is intrinsically strong or stable, but because it forms a continuous layer that binds together the original cement particles into a cohesive whole. The binding ability of C-S-H phase arises from its nanometer-level structure. In terms of chloride penetration in concrete, C-S-H phase is known to adsorb chloride ions, however, its mechanism is very complicated and still not clear. The purpose of this study is to examine the interaction between chloride ions and C-S-H phase with various Ca/Si ratios and identify the adsorption mechanism. C-S-H phase can absorb chloride ions with 3 steps. In the C-S-H phase with low Ca/Si ratios, momentary physical adsorption could not be expected. Physical adsorption is strongly dependent on electro-kinetic interaction between surface area of C-S-H phase and chloride ions. For C-S-H phase with high Ca/Si ratio, electrical kinetic interaction was strongly activated and the amount of surface complexation increased. However, chemical adsorption could not be activated for C-S-H phase with high Ca/Si ratio. The reason can be explained in such a speculation that chloride ions cannot be penetrated and adsorbed chemically. Thus, the maximum chloride adsorption capacity was obtained from the C-S-H phase with a 1.50 Ca/Si ratio.

• Cement Symposium
• /
• no.25
• /
• pp.36-40
• /
• 1997

• Journal of the Korean Ceramic Society
• /
• v.31 no.10
• /
• pp.1231-1239
• /
• 1994

In this study, gel powder which had relatively high hydration reactivity in CaO and P2O5 rich composition of CaO-P2O5-SiO2-H2O system was prepared by sol-gel process and its hydrated specimen was manufactured. The it was investigated to appropriate calcination temperature in sol-gel process which hydrated specimen of gel powder have proven to strength and the effect of factors influenced strength in hydration process. The major product of before and after hydration reaction was hydroxyapatite, and crystalline phase of C-S-H was already formed during gelation process. After hydration reaction of pressed specimen, crystalline phase of C-S-P-H was formed. It was hydrated product of silicocarnotite (5CaO.P2O5.SiO2). Gel phases of C-S-H and C-S-P-H occured as a result of partial substitution of amorphous silica by P2O5 was formed. The strength of hydrated hardened body is developed by strong bonding and bridging between the gel phases of C-S-H or C-S-P-H and the crystalline products such as hydroxyapatite, Ca(OH)2 C-S-H and C-S-P-H. In addition, the ultrafine gel powder have an great effect on increase of hydration reaction.

• Journal of the Korea Concrete Institute
• /
• v.27 no.1
• /
• pp.85-92
• /
• 2015

The chloride ions, responsible for the initiation of the corrosion mechanism, intrude from the external medium into the concrete. A part of the intruding chloride ions will be retained by the hydration products of the binder in concrete, either through chemical adsorption or by physical adsorption. Since the hydration products of cement are responsible for the chloride binding in concrete, this study focused on the chloride binding in individual hydrate. The purpose of this study is to explore the time dependant behaviors of chloride ions adsorption with cement hydrates, focused on its mechanism. AFt phase and CH phase were not able to absorb chloride ion, however, C-S-H phase and AFm phase had a significant chloride adsorption capacity. In particular, AFm phase showed a chemical adsorption with slow rate in 40 days, while C-S-H phase showed binding behaviors with 3 stages including momentary physical adsorption, physico-chemical adsorption, and chemical adsorption. Based on the results, this study suggested theoretical approach to depict chloride adsorption behavior with elapsed time of C-S-H phase and AFm phase effectively. It is believed that the approach suggested in this study can provide us with a good solution to understand the mechanism on chloride adsorption with hydrates and to calculate a rate of chloride penetration with original source of chloride ions, for example, marine sand at initial time or sea water penetration later on.

• Journal of ILASS-Korea
• /
• v.5 no.4
• /
• pp.57-65
• /
• 2000

For this research an extension of the LIF technique that the LIEF(Laser Induced Exciplex Fluorescence) technique has been used LIEF technique is the unique method to allows the visualization of fuel vapor phase and liquid phase individually by capturing each signals of them. In this work performed that the basic procedure for advanced LIEF technique using TEA and benzene as dopants md high power KrF excimer laser to excite the dopants. Iso-octane is used as the fuel because it does not absorb light at the laser wavelength. The boiling point of benzene and TEA are $81^{\circ}C\;and89^{\circ}C$, respectively, in comparison to $99^{\circ}C$ for iso-octane. It is observed that the behavior and distribution of high pressed fuel injection from various test condition. The injection pressure is set as 3MPa. and 5MPa. And the ambient pressure of test chamber is atmospheric pressure and 1MPa, the ambient temperature of chamber is room temperature, $300^{\circ}C\;and\;500^{\circ}C$ to imitate the condition of GDI engine cylinder.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.119-121
• /
• 1998

Phase controller is made and tested to estimate the characterics of superconductor. Phase controller using the DSP2104 can determine the closing phase angle and period of transport current increased by shorting bypassed circuit. In this paper, the experimental results are described.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.25 no.5
• /
• pp.392-398
• /
• 1992

Field study on the sporogenesis periods of 16 red algae growing at the intertidal zone of Daesongri was conducted from April 1987 to March 1988, obseuing the occurence of carposporic and tetrasporic fronds. The period of Gloiopeltis furcata was in spring and summer; that of Laurencia intermedia, Laurencia undulata and Rhodymenia intricate in summer; that of Chondria dasyphylla and Hypnea charoides in autumn; that of Carpopeltis affinis, Pachymeniopsis lanceolata, Chondrus ocellatus, Awosorium polyneunm, Gymnogongrus flabelliformis, Gigartina intermedia, Champia parvula and Ceramium paniculatum in summer and autumn. Of the species, G. flabelliiformis, G. intermedia and R. intricate only matured the carposporic phase, and P. telfairiae, H charoides, C. parvula and C. paniculatum did the tetrasporic phase. But the carposporic phase of G. flabelliformis and the tetrasporic phase of C. paniculatum were not occured in Kori area where water temperature was 3 C higher than that in Daesongri. In that area they only matured the other phase. This suggests that the life history is rarely complete in nature and water temperature is a important factor influencing on the sporogenesis. Also it was observed in C. affinis, C. ocellatus and S. latiuscula that the period of one phase is much longer than that of the other phase. But in most of species with both phases, tatrasporic and caropsporic, the former phase appeared a month later than the latter phase. In addition, their biomass became maximum just before sporgenesis, and then gradually decreased with release of reproductive cells.

• Journal of Magnetics
• /
• v.15 no.2
• /
• pp.61-63
• /
• 2010

We used $^1H$ nuclear magnetic resonance (NMR) to study the phase transitions and molecular dynamics in a characteristic ferroelectric liquid crystal with a carbon number n = 7, S-2-methylbutyl 4-n-heptyloxybiphenyl-4'-carboxylate (C7). The results were compared with those of our recent work on S-2-methylbutyl 4-n-octanoyloxybiphenyl-4'-carboxylate (C8), with a carbon number n = 8. While the recrystallization and isotropic phase transitions exhibited a first-order nature in the $^1H$ NMR spin-lattice and spin-spin relaxation measurements, a second-order nature was shown at the Sm-A - Sm-$C^*$ liquid crystalline phase transition. A soft-mode anomaly arising from the tilt angle amplitude fluctuation of the director, of which only a hint had been noticed in the C8 system, was manifested in the C7 system at this transition.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.908-911
• /
• 1993

The single-Phase induction motor is widely used in many light duty applications. especially in home and the office. At present, many applications which use these motor require continuously adjustable speed control. In the general, the speed control of single-phase induction motor is accomplished at a few discrete speeds by using tapped-windings, pole switching or gear. These techniques is inefficient and complicated. In this paper, auxiliary winding voltage phase angle of single-phase induction motor is used to continuously adjust electromagnetic torque. The analysis includes the determination of the relationship between the auauxiliary winding voltage phase angle and torque. Simulation results of the motor's torque-speed characteristics using the controlled auxiliary winding supply are shown and discussed. The drive is tested using a dynamometer to experimentally verify the results of the theory and simulations.

• Progress in Superconductivity
• /
• v.3 no.1
• /
• pp.91-94
• /
• 2001

By varying fabricating process, precursor powders with different initial conditions were prepared. Subsequently, Bi-2223/Ag tapes were made through these powders. The effects of precursor powders on the phase evolution and Jr properties of Bi-2223/Ag tapes were studied along with several thermomechanical cycles. Our results showed that the initial conditions of precursor powders could strongly influence the phase formation rate and $J_{c}$ value in final tapes. The factors of precursor powders that influence the phase formation and $J_{c}$ of Bi-2223/Ag tapes must be studied and optimized in combination.ion.