• Journal of the Korean Society for Heat Treatment
• /
• v.29 no.6
• /
• pp.259-263
• /
• 2016

This study was carried out to investigate the effect of hot forging ratio on the microstructure and mechanical properties of incoloy 825 alloy. Hot forging was carried out at the forging ratio of 0%, 60% and 90% respectively in a range of $900^{\circ}C{\sim}1,140^{\circ}C$ and followed solution treatment was conducted at $1,000^{\circ}C$ for 1 hr. In all the specimens of hot forged of 0%, 60% and 90%, precipitates were not observed. The average grain size of 0% specimen is $82{\mu}m$ and that of 60% and 90% is $56{\mu}m$ and $31{\mu}m$, respectively. The range of grain size in the 0% specimen is uneven in $182{\mu}m$ to $31{\mu}m$, but the grain size of 90% specimen is uniform. With increasing hot forging ratio, the mechanical properties such as tensile strength, elongation, hardness increased and impact toughness increased by grain refinement.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.2 s.233
• /
• pp.263-270
• /
• 2005

An experimental study was performed to investigate the effects of partially premixing, varying the equivalence ratios from $0.79{\sim}{\infty}$, on NOx emissions and chemiluminescence of excited $OH^{\ast},\;CH^{ast}\;C_2^{\ast}$ radicals in laminar partially premixed flames. the signal from the electronically excited state of $OH^{\ast},\;CH^{ast}\;C_2^{\ast}$ was detected through a band pass filter with a photo multiplier tube, which are processed to the intensity ratio ($C_2^{\ast}/CH^{\ast},\;C_2^{\ast}/OH^{\ast},\;and\;CH^{\ast}/OH^{\ast}$) to reveal the correlation with local equivalence ratio. And measurements of NOx emission were made to investigate the relationship between visible flame appearance, chemiluminescence, and EINOX. The results demonstrated that (1) the flames at ${\phi}<1.59$ exhibited classical double flame structure, at ${\phi}>4.76$, the flames exhibited diffusion flame structure, and the intermediate flames at $1.59<{\phi}<4.76$ was a merged flame, (2) the $OH^{\ast}$ peak was located inside the $CH^{\ast}\;and\;C_2^{\ast}$ radical for all measured conditions and the emission intensity ratio of $C_2^{\ast}/CH^{\ast}\;and\;C_2^{\ast}/OH^{\ast}$ were identified as good marker for local equivalence ratio over a range of ${\phi}=0.79{\sim}1.2\;and\;CH^{\ast}/OH^{\ast}\;is\;0.79<{\phi}<1.9$. However, it was difficult to predict the equivalence ratio in partially premixed flames using this system for ${\phi}>2.38$, (3) the minimum NOX emission index (EINOx) is obtained for a equivalence ratio of 3.19 in the intermediate flames.

• Plant Journal
• /
• v.14 no.4
• /
• pp.33-38
• /
• 2018

In this study, it was confirmed whether the cooling water bypass ratio of packing for plume abatement matched designed value during winter operation of combined cycle power plant. Designed operating wet bulb temperature of the plume abatement cooling tower with 29 Gcal/h capacity had a range from $13^{\circ}C$ to $-20^{\circ}C$, while its designed bypass ratio was from 0 % to 78%, so that increasing rate of the designed bypass ratio was $2.36%/^{\circ}C$ when the external temperature decreased. When the wet bulb temperature at cooling tower inlet had a range from $7.8^{\circ}C$ to $-11.8^{\circ}C$ in a normal operation, it was measured that actual bypass ratio of packing for plume abatement had a range from 23.8 % to 74.3%. While increasing rate of the actual bypass ratio was $2.71%/^{\circ}C$ in a range from $7.8^{\circ}C$ to $-9.55^{\circ}C$, it was $1.61%/^{\circ}C$ under $-10^{\circ}C$ in cold weather condition according to atmospheric temperature drop, therefore it was confirmed that the increasing rate of the bypass ratio for packing was lowered than its design.

• Restorative Dentistry and Endodontics
• /
• v.5 no.1
• /
• pp.29-34
• /
• 1979

The purpose of this study was to measure thermal expansions of dental investments, Biovest(Casting Investment. Dentsply International INC, U.S.A.), Multi-Best (Use for all dental chrome-cobalt alloys, The Ransom & Randolph Co. U.S.A.), Kerr(Inlay Investment. Sybron Kerr, U.S.A.), O. K. (Inlay Investment. Shofu Dental MFG, Co. Japan), Whip-Mix (Cristobalite Inlay Investment. Whip-Mix Corporation. U.S.A.). Thermal expansion of specimens(5mm in diameter and 50mm in length) was measured by a dilatometer at the temperature range from $20^{\circ}C$ to $700^{\circ}C$ by comparing expansion between standardized quartz and experimental specimens with heating rate about $300^{\circ}C$/hr. The following results were obtained. 1. The coefficient of thermal expansion of Biovest was $15{\times}10^{-6}/^{\circ}C$ in the water powder ratio 18/100 and $14{\times}10^{-6}/^{\circ}C$ in the water powder ratio 28/100. Those of Multi-Best were $9{\times}10^{-6}/^{\circ}C$ in the water powder ratio 14/100 and $7{\times}10^{-6}/^{\circ}C$ in the water powder ratio 24/100. 2. The coefficient of thermal expansion of Kerr were $17{\times}10^{-6}/^{\circ}C$ in the water powder ratio 38/100 and $14{\times}10^{-6}/^{\circ}c$ in the water powder ratio 48/100. Those of O. K. were $9{\times}10^{-6}/^{\circ}C$ in the water powder ratio 33/100 and $7{\times}10^{-6}/^{\circ}C$ in the water powder ratio 43/100 3. The coefficient of thermal expansion of Whip-Mix were $14{\times}10^{-6}/^{\circ}C$ in the water powder ritio 40/100 and $12{\times}10^{-6}/^{\circ}c$ Fein the water powder ratio 50/100. Those of Hi-Heat were $11{\times}10^{-6}/^{\circ}c$ in the water powder ratio 28/100 and $10{\times}10^{-6}/^{\circ}c$ in the water powder ratio 38/100.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.355-356
• /
• 2009

The change of thermal expansion and mechanical behaviors by cold working has been investigated in Fe-29%Ni-17%Co low thermal expansion Kovar alloy. Fe-29%Ni-17%Co alloy was cold rolled gradually and prepared to plates having reduction ratio of 0%, 20%, 40%, 60%, and 80%. Annealing effect on the properties was also studied. Thermal expansion was measured from $25^{\circ}C$ to $600^{\circ}C$ with a heating rate of $5^{\circ}C$/min by using vacuum differential dilatometer. It was found that thermal expansion coefficient ($\alpha_{30{\sim}400}$) slightly decreased (reduction ration of 20%) and then remarkably increased (above reduction ration of 40%) with increasing reduction ratio of cold rolling. Thermal expansion coefficient ($\alpha_{30{\sim}400}$) was sharply decreased after annealing heat-treatment. Yield and tensile strengths were continuously increased and elongation was decreased by cold roiling. Microstructural observation and X-ray diffraction analysis results showed that the $\alpha$ phase significantly increased as the reduction ratio increased. The slight decrease of thermal expansion coefficient bellow reduction ration of 20% could be explained by the destroying short-range ordering and the decreasing of grain size. The significant increase of thermal expansion coefficient with cold rolling mainly attributed to the appearance of $\alpha$ phase. The correlation between the microstructural cause and invar phenomena for the low thermal expansion behavior was also discussed.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.7
• /
• pp.385-389
• /
• 2017

Generally, refrigerant temperature out of the receiver is assumed to be saturated. This may be true for horizontal or vertical receivers having small aspect ratio. However, this assumption needs verification for vertical receiver having large aspect ratio. No study has reported information on this issue. The objective of this study was to determine the effect of liquid level and mass flow rate on liquid subcooling of a long vertical receiver using R-410A. During the test, inlet subcooling was maintained at $5^{\circ}C$ while saturation temperature was maintained at $10^{\circ}C$. Results showed that subcooling was maintained for the long vertical receiver. Subcooling preservation ratio (ratio of exit to inlet subcooling) was increased as mass flow rate or liquid level was increased. As a whole, 50 to 70% subcooling preservation was possible for the present receiver. Further investigations are needed to enhance information on this issue using receivers having different aspect ratios.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.3
• /
• pp.171-176
• /
• 2014

PURPOSE. The aim of this study was to determine the absolute value of the root/crown ratio (R/C ratio) using panoramic radiographs (PRGs) in a healthy Korean population. MATERIALS AND METHODS. In total, 99 patient radiographs (of 50 males and 49 females subjects; aged 16 to 24 years old) were examined, and 2,770 teeth were analyzed. Crown lengths and root lengths were measured with modified Lind's measurements using PACS tools by two examiners in two separate sessions two months apart. All data were analyzed using SPSS. The independent t-test was used to assess for gender differences, and the paired t-test was used to compare both arches with a significance level of P<.05. RESULTS. The mean R/C ratios varied from 1.29 to 1.89 (male: 1.28-1.84; females: 1.31-1.94). The highest R/C ratios were recorded for the mandibular canines (1.89), followed by the maxillary canines (1.79). The lowest R/C ratios were recorded for the maxillary second molars (1.31). In comparison with the maxillary teeth (1.29-1.78), the mandibular teeth yielded the higher R/C ratio (1.47-1.89), and this difference was significant in the females (P<.05). The difference between the genders was not statistically significant, except for the maxillary central incisors, mandibular canines and mandibular first premolars. CONCLUSION. These data may enhance the understanding of the clinical R/C ratio as a useful guideline for determining the status of teeth and the ethnic difference.

• Journal of Environmental Science International
• /
• v.29 no.5
• /
• pp.531-539
• /
• 2020

To understand the composition, quantity, and quality of Suspended Particulate Organic Matter (SPOM) in the Gangneung Namdae Stream, Korea, we examined spatiotemporal variations in water temperature, salinity, chlorophlly a (Chl a), Particulate Organic Carbon (POC) and nitrogen (PON), and carbon stable isotope (δ¹³C) of SPOM at six stations in June (pre-monsoon), July (monsoon), and September (post-monsoon) 2017. With increasing precipitation, the average POC and C/N values increased significantly in July than in June. In September, the values decreased with decreasing precipitation. The δ¹³C values showed irregular spatiotemporal fluctuations among the stations and periods, thereby suggesting a greater contribution of autochthonous organic matter to the pool of SPOM than that of allochthonous organic matter derived from upstream. In addition, the large and irregular changes in POC, C/N ratio, C:Chl a, and δ¹³C compared to that of PON were observed for all periods among the stations, indicating a serial discontinuity of the stream. Our results suggest that the Gangneung Namdae Stream is significantly influenced by the increase in freshwater discharge caused by heavy rainfalls during the summer monsoon and post-monsoon periods.

• Korean journal of applied entomology
• /
• v.52 no.1
• /
• pp.29-33
• /
• 2013

The fecundity of summer generation adults of arrowhead scale, Unaspis yanonensis (Kuwana) (Hemiptera: Diaspididae), was examined at constant temperatures. The total fecundity increased up to $29^{\circ}C$ and declined thereafter. Total fecundity reached a maximum of 254.5 eggs (crawlers) per female at $29^{\circ}C$. Females showed periodic oviposition activity but the pattern differed with temperature. Three or more oviposition cycles were occurred at 25 and $29^{\circ}C$. At the other temperatures, the 2nd oviposition cycle was reduced or obscure. And oviposition cycle after the 2nd cycle was not obvious at low or high temperatures. The fecundity of the 1st cycle was significantly different according to temperature, showing higher fecundity at 25 and $29^{\circ}C$. Fecundity after 1st cycle at 13, 17 and $21^{\circ}C$ were lower than at 25 and $29^{\circ}C$. The sex ratios of hatched nymphs in terms of female : male in 13, 17, 25, 29 and $33^{\circ}C$ were 1 : 0.48, 1 : 4.79, 1 : 2.48, 1 : 1.85 and 1 : 0.56, respectively.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.24 no.3
• /
• pp.385-392
• /
• 2000

The adsorption ability of dyes on chitin, a natural polymer was investigated for decolorization of dye wastewater. Chitin was manufactured in lab by decalcification in dilute aqueous HCI solution and deproteination in dilute aqueous NaOH solution with shrimp shells. Absorbance of residue solution of dyebaths after dye adsorptions of chitin were measured in varieties of dye concentration and dipping periods. Four kinds of dyestuffs were used, C.I.Acid Blue 29. C.I.Direct Blue 6, C.I.Reactive Orange 12 and C.I.Basic Red 18. When chtin 1g was dipped in 0.05% of dyebath with stirring, maximum adsorption ratio of each kind of dyes was exhibited as 91.6% for C.I.Acid Blue 29, 95% for C.I.Direct Blue 6, 58.2% for C.I.Reactive Orange 13 and 75.8% for C.I.Basic Red 19. It shows that chitin has better adsorption abilities of ionic dyes of acid, direct and basic dye than non-ionic reactive dye. And chitin has better adsorption abilities of anionic acid direct dyes than cationic basic dye because of the presence of nitrogen atoms. All kinds of dyestuffs used showed speedy absorption effects by chitin, so chitin can absorb much amount of dyes in 5 mimutes reach to equilibrium of adsorption in 2 hours after dipping. Basic dye was absorbed the most speedily in 5 minutes, although maximum adsorption ratio is not high. That reason can be thought that chitin surface is essentially negatively charged due to polar funtional groups.