Drop-in tests were conducted using R290/R32 (31:69) mixture in an ice-cream maker for possible replacement of R-502 and R-404A. Optimum refrigerant charge and TEV opening were obtained through a series of experiments. At the standard outdoor condition ($35^{\circ}C$ DT, $24^{\circ}C$ WT), the time required for initial ice-cream making was 6'22", which was approximately the same as that of R-404A. The electric energy consumed was 660 kJ, which was about 10% higher than that of R-404A. The compressor outlet temperature ($8^{\circ}C$) and pressure (2.52 MPa) were higher than those ($60^{\circ}C$ and 1.48 MPa) of R-404A. The reason could be the usage of the same R-404A compressor although the specific volume of R290/R32 is much larger.
Experiments were carried out to investigate the condensation heat transfer characteristics for R22 and its alternatives, R407C (R32/125/134a, 23/25/52wt%) and R410A (R32/125, 50/50wt%). A concentric tube heat exchanger was made to conduct condensation heat transfer tests. Mass flux and saturation temperature of refrigerants at the test section inlet were varied to get the corresponding heat transfer coefficients. Serial and parallel input of secondary fluid (water) were applied to the test subsections. Compared with existing correlations of condensation heat transfer, experimental heat transfer coefficients obtained in this study were generally higher than the predicted values, and mean absolute deviations from several correlations were shown. Wall subcooling was introduced to get a new correlation for condensation heat transfer coefficients by modifying Shah's equation. The RMS deviation of the measured heat transfer coefficients from the new correlation in this study for R22 is 9.9% and that for R407C and R410A are 10.2% and 14.6%, respectively.
복합재료 제작 기술은 저비용, 유연성 그리고 용이한 가공성 등을 그대로 유지하면서 필러(filler)의 특성을 부여하는 방법을 지향하고 있으며 다양한 기능성 복합재료 개발로 이루어지고 있다. 기능성 복합재 구현과 관련하여 그래핀(Graphene)을 필러로 사용하는 복합재료의 고성능화 연구가 활발히 진행되고 있다. 본 연구에서는 기능성 물성치 향상을 위해 많이 사용되는 그래핀을 이용하여 물리 화학적 물성치를 고찰하였다. 대표적 filler인 graphane nanoplatelet(GNP)을 사용하여 그래핀 옥사이드(graphene oxide, GO)를 제조하였고 그래핀 옥사이드(GO) 를 환원시켜 reduced graphene oxide(R-GO)를 형성하였다. 각기 제조된 GO와 R-GO의 물성치를 분석하였고 이를 GNP 분석결과와 비교하여 제조된 방법의 신뢰성을 검토하였다. Raman 분광법에 의한 분석 결과 R-GO의 경우 GO에 비해 D-peak와 G-peak의 강도의 감소를 확인할 수 있었고 ID/IG의 비를 통해 0.08의 증가 값을 볼 수 있었다. FTIR을 이용한 GNP, GO 및 R-GO의 작용기 분석 결과 C-C, C=C의 반복되는 연결 구조를 가진 GNP와는 다르게 GO 및 R-GO의 경우 명확한 peak를 통해 C-O 결합, C=C 결합, C=O 결합 및 O-H 결합을 확인할 수 있었다. X-ray 회절 분석 결과 GNP는 (002) 평면 특성의 25.86°에서 넓은 회절의 peak를 보인 반면 GO와 R-GO는 (001), (100) 평면에 해당하는 peak를 볼 수 있었고 GO의 층간거리는 GNP에 비해 약 2.6배 증가한 것을 확인할 수 있었다.
Through enrichment on two nutrient agars, 57 Thermus isolates were recovered from 15 hot spring samples taken from the Rehai geothermal area, Tengchong, China. Unique growth characteristics were observed when the strains were transferred from YIM14 medium to Thermus medium. Phylogenetic analysis showed that the 16S rDNA sequences of the isolates and clones from the Rehai geothermal area farmed a monophyletic group on the phylogenetic tree. A secondary structure comparison showed that their 16S rRNAs have unique secondary structure characteristics.
본 연구는 중소 벤처기업들의 태생적 약점을 극복하게 해 주는 것으로 알려진 사회적 네트워크와 그 원천인 정치적 기술 간의 관계구조를 실증 고찰한 연구이다. 211명의 벤처기업가 응답을 근거로 한 구조방정식 모형 분석 결과, 첫째 네트워킹 능력은 사회적 네트워크의 약한 유대(${\beta}$=.527, C.R.=3.626), 강한 유대(${\beta}$=.594, C.R.=3.969), 네트워크 중심성(${\beta}$=.418, C.R.=4.884)에 모두 유의하고 강한 정(+)의 영향을 미치는 것으로 나타났으며, 둘째, 사회적 통찰력 역시 약한 유대(${\beta}$=.192, C.R.=1.701), 강한 유대 (${\beta}$=.269, C.R.=2.509) 그리고 네트워크 중심성(${\beta}$=.228, p=2.283)에 유의한 정(+)의 영향을 미치는 것으로 나타났다. 셋째 대인관계 영향력은 강한 유대(${\beta}$=-.264, C.R.=-1.862)와 네트워크 중심성(${\beta}$=-.394, C.R.=-2.914)에만 유의한 영향을 미치는 것으로 나타났는데 부호의 방향이 (-)인 것으로 나타났다. 마지막으로 외형적 진실성은 사회적 네트워크의 하부요인들에 유의한 영향을 미치지 않는 것으로 나타났다. 연구결과는 사회적 네트워크와 사회적 역량의 관계를 실증 분석했다는 점 외에 중소 벤처기업 기업가들에게 그들의 태생적 한계 극복을 위한 실제적인 정보를 제공했다는 점에서 의의가 있다. 또한 사회적 역량의 구체적 실체인 정치적 기술 개념을 제안하고 실증분석 함으로써, 기업가적 역량 구축에 관심을 둔 향후 연구들의 이론적 토대를 제공했다는 점에 큰 의의가 있다.
Thermodynamic performance of eight zeotropic R-22 alternative refrigerant mixtures selected by AREP(R-22 Alternative Refrigerants Evaluation Program) and R-32/R-125/R-134a(23%/25%/52%), namely R-407C were evaluated by the "drop-in" simulation method. An existing air conditioner was selected and its design data were used for the simulation. "ARI Test A" air conditions were applied. The degree of vapor superheat at the compressor inlet fixed at $5^{\circ}C$ for all the mixtures. The results of the simulation were compared with those of R-22. COPs of all mixtures except for R-32/R-227ea(35%/65%) and R-32/R-125/R-134a(10%/70%/20%), were higher than that of R-22 by 2%~8%, while the capacities were all lower than that of R-22 by 13%~27%. COP of R-32/R-134a(40%/60%) was 2.4% higher but the capacity was 15% lower than those of R-22. In the case of R-32/R-134a(30%/70%), COP and capacity were 5.5% higher and 15% lower than those of R-22, respectively. Among the ternary mixtures, R-407C and R-32/R-125/R-134a(30%/10%/60%) showed the best performance. COP of R-407C was 2.4% higher than those of R-22 but the capacity was 15% lower.
This paper presents the results of an experimental investigation on the flexural behavior of doubly reinforced lightweight concrete (R.L.C.) beams tested under cyclic loading. A total of 20 beam specimens were tested. Test results are presented in terms of ductility index, the degradation of strength and stiffness, and energy dissipation. The flexural properties of R.L.C. beam were compared to those of normal concrete (R.C.) beams. Test results show that R.L.C. beam with low and medium concrete strength (20, 40MPa) performed displacement ductility similar to the R.C. beam. The ductility can be improved by enhancing the concrete strength or decreasing the tension reinforcement ratio. Using lightweight aggregate in concrete is advantageous to the dynamic stiffness of R.L.C. beam. Enhancement of concrete strength and increase of reinforcement ratio will lead to increase of the stiffness degradation of beam. The energy dissipation of R.L.C beam, similar to R.C. beam, increase with the increase of tension reinforcement ratio. The energy dissipation of unit load cycle for smaller tension reinforcement ratio is relatively less than that of beam with higher reinforcement ratio.
버들치 Rhynchocypris oxycephalus와 버들개 R. steindachneri를 대상으로 마취 수온 10도C, 15도C 및 20도C에서 염산리도카인(염산리도카인/NaHCO하(3))의 마취 효과를 조사하였다. 마취 시간과 회복 시간을 고려시 효과적인 염산리도카인 농도는 버들치에서 300ppm ($20^{\circ}C.$), 400ppm ($15^{\circ}C.$) 및 600ppm ($10^{\circ}C.$) 이었고 버들개에서 400ppm ($20^{\circ}C.$), 500ppm ($15^{\circ}C.$) 및 600ppm ($10^{\circ}C.$) 이었다. 마취시간과 회복시간에 있어 버들치 속 2종은 염산리도카인 농도 및 마취 수온 의존적이었다. 각 염산리도카인 농도에서 개체 크기가 증가할수록 마취 시간이 길어졌으며, 개체 크기가 큰 군은 마취 농도가 증가할수록 회복 시간 역시 길어졌다. 본 연구 결과 염산리도카인은 버들치 속어류 마취에 효과적인 것으로 판명되었다.
Bacillus subtilis에 존재하는 DEAD-box RNA helicase 유전자의 결손이 저온 충격에 민감성을 보이는지를 조사하였다. 저온 충격에 민감한지를 알아 보기 위하여 대수기에($O.D_{600}$=0.5-0.6) 있는 세포를 $15^{\circ}C$도 낮추어 저온충격을 가하여 생장하는 정도를 조사하였다. DEAD-box RNA helicase 유전자 ydbR, yfmL, yqfR, deaD의 결손 균주들이 저온충격을 가하였을 때 ydbR 결손 균주의 생장이 야생형 균주에 비해 5배 정도 현저히 감소하였으나, 다른 DEAD-box RNA helicase 유전자의 (yfmL, yqfR, deaD) 결손은 야생형 균주와 비슷한 생장을 보였다. 저온에서의 유전자 발현을 알아보기 위하여 Northern blot으로 mRNA 양을 알아본 결과 $37^{\circ}C$에 비해 $15^{\circ}C$에서 ydbR과 yqfR의 mRNA전사물 증가를 확인할 수 있었고, 반면에 yfmL과 deaD의 전사 증가는 관찰되지 않았다. $37^{\circ}C$에서 $15^{\circ}C$로 저온 충격을 가하면 ydbR mRNA 양의 뚜렷한 증가를 확인하였고, 전사 억제제인 rifampicin를 처리하여 ydbR mRNA의 양을 조사하였을 때 $15^{\circ}C$ 조건에서는 mRNA 양이 거의 유지하는 반면에 $37^{\circ}C$ 조건에서는 급격한 mRNA의 감소가 일어나 전사과정에서 유도되기 보다는 전사 후 전사물의 안정에 기인하는 것으로 보인다. 이와 관련하여 ydbR 유전자의 5' UTR (untranaslated region) 부근에서 csp (cold shock protein) 유전자에서 관찰되는 cold box element를 확인하였고, ydbR이 저온 충격 조건에서 발현되는 과정이 csp와 유사하게 전사물의 안정성에 기인함을 알 수 있었다.
This study presents test results of a residential window system air-conditioner using R22 and two potential alternative refrigerants, R407C and R410B. A series of performance tests was performed for the basic and liquid-suction heat exchange cycle in a psychrometric calorimeter test facility. For R407C, the same rotary compressor was used as in the R22 system. However, compressor for the R410B system was modified to provide the similar cooling capacity. The evaporator circuit was changed to get a counter-cross flow heat exchanger to take advantage of zeotropic mixture's temperature glide, and liquid-line suction-line heat exchange cycle was also considered to improve the performance of the system. Test results were compared to those for the basic R22 system.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.