• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1115-1121
• /
• 2017

In order to obtain high thrust at the beginning of the flight, the solid rocket motor with large initial burning surface area was designed and tested. From the static firing test, lower initial thrust was obtained compared with the expected thrust based on the internal ballistic prediction due to the negative erosive burning effect which reduced the burning rate estimated by APN Law. In addition, the radial mode combustion instability was observed with 8 fins grain configuration. This instability was removed after the odd number of fins were used.

• Journal of the Korean Ceramic Society
• /
• v.27 no.2
• /
• pp.211-218
• /
• 1990

CA2-based clinker with highly activated surface and hydraulic properties was synthesized at a comparatively lowr temperature than that of conventional synthesis by "hydration-burning method". This consists of calcining the mixture of CaCO3 and Al2O3 to obtain a primary clinker, hydrating the primary clinker and reburning the hydrates to obtain final clinker. Burning of primary clinker above 1200℃ was necessary to eliminate free CaO in it and to obtain it's solid hydrate. However, rising the burning temperature above 1300℃ is ineffective due to the decrease in hydraulic properties of the primary clinker with the temperature. Hydration of primary clinker at the elevated temperature(>35℃) was required to obtain the hydrate with more porous structure and final clinker with more active surface. CA2 was formed and increased with temperature at above 1150℃, finally became a primary phase of the final clinker. However, burning at the temperature above 1300℃ resulted in reverse effect on the hydraulic properties of the final clinker due to rapid decrease in it's surface area with the temperature.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.5
• /
• pp.493-502
• /
• 2012

Syngas laminar burning velocity measurements were carried out at atmospheric pressure and ambient temperature using the Bunsen flame configuration with nozzle burner as a fundamental study on flame stability of syngas fuel. Representative syngas mixture compositions ($H_2$:CO) such as 25:75%, 50:50% and 75:25% and equivalence ratios from 0.5 to 1.4 have been conducted. Average laminar burning velocities have been determined by the stabilized nozzle burner flames using the angle method, radical surface area method and compared with the data obtained from the other literatures. And the results of each experimental methodologies in the various composition ratios and equivalence ratios were coincided with the result of numerical simulation. Especially, it was confirmed that there was necessary to choice a more accurate measurement methodology even the same static flame method for the various composition ratios of syngas fuel including hydrogen. Also, it was reconfirmed that the laminar burning velocities gradually increased with the increasing of hydrogen content in a fuel mixture.

• The Journal of Engineering Geology
• /
• v.17 no.2 s.52
• /
• pp.225-233
• /
• 2007

The engineering properties of surface soils in natural terrain are changed due to wildfire. This change of engineering properties induced by wildfire is related to landslides occurrence. To investigate the change of soil properties caused by wildfire, the various soil tests are performed. The soil samples are obtained from the recently burned slopes of Yangyang area, Kangwon Province. The soil samples obtained from the burned slopes are classified into three types depending on the burning grade: the perfect burning grade, the intermediate burning grade, the non-burning grade. As the result of tests, the specific gravity and the dry unit weight of soils obtained from perfect and alternative burning grades are less than those of soils obtained from non-burning grade. It judges that an electronic force, ionic components and of soils are changed and organic matters in soils are burned by wildfire. The permeability of soil obtained from alternative burning grade is the lowest and that of soil obtained from perfect burning grade is the highest. The water-repellent layer is formed on soil surface by wildfire. The water-repellent layer is existed at the area of alternative turning grade, while the layer is not existed at the area of perfect burning grade. The water-repellent layer is collapsed in high temperature more than about $400^{\circ}C$.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.2
• /
• pp.12-19
• /
• 2022

Propellant grains with embedded metal wires have been used for enhancement of burning rate while maintaining high loading density. For the performance design of a solid rocket motor using propellant grain with embedded metal wires, burn-back analysis is required according to number, location, arrangement angle of metal wires, and augmentation ratio of the propellant burning rate near a wire region. In this study, a numerical method to quickly calculate a burning surface area was developed in response to the design change of the propellant grain with embedded metal wires. The burning surface area derived from the developed method was compared with the results of a CAD program. Error rate decreased as the radial size of the grid decreased. Analysis for characteristics of burning surface area was performed according to the number and location of metal wires, the initial and final phases were shortened and the steady-state phase was increased when the number of metal wires increased. When arranging the metal wires at different radii, the burning surface area rapidly increased in the initial phase and sharply decreased in the final phase compared to the case where the metal wires were disposed in the same radius.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.65-72
• /
• 2003

In order to clarify turbulent combustion characteristics of hydrocarbon mixtures by hydrogen addition, turbulent burning velocities in a constant volume vessel were measured for both lean and rich hydrocarbon mixtures. Moreover, the configuration characteristics of turbulent flame was investigated in the wrinkled laminar flame region. A laser tomography technique was used to obtain the images of turbulent flame, and quantitative analyses were performed. As a result, the characteristics of turbulent burning velocity was shown a distinct difference with the addition rate of hydrogen between lean and rich mixtures. On the other hand, the obtained tomograms showed that the surface area of turbulent flame depends almost only on the turbulence intensity.

• Journal of Energy Engineering
• /
• v.11 no.2
• /
• pp.166-177
• /
• 2002

The present study is described of the flame structure of one-dimensional, flat, premixed, laminar, coal-air flame with some addition of methane for the flame stability. A low pressure burner operating at a combustion pressure of 0.3 arm was employed in order to extend the reaction zone. Predicted results from the models considered in the present study are compared with experimental results. Comparisons are included gas temperatures, species concentrations, char analysis and measured burning velocity. Among the models, Model II $I^{*}$-d, which specified devolatilization rate constants and a char surface area factor S=4, resulted in good agreement within the present experimental ranges. The results of char analysis suggest that the extent of the reaction occurring on the panicle might be underestimated in the model so that the char surface area should be increased. A value of 4 for this factor was given by sensitivity analysis of change in char surface area. Again, model II $I^{*}$-d gave satisfactory predictions of burning velocities over most of the experimental range studied. It has been clearly shown that the particle diameter appreciably affects the rates of devolatilisation and char oxidation through the effects of thermal lag and volumetric reactive surface area, consequently laminar burning velocity.ity.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.8
• /
• pp.2030-2038
• /
• 1995

In this study, three turbulent flame propagation models are compared using experimentally measured data of a 4 valves/cylinder spark-ignition engine. First two conventional models are B.K model and GESIM combustion model. The burning rates calculated from the two models are compared with the burning rates calculated from measured pressure data using the one-zone heat release analysis. GESIM combustion model predicts burning rates closer to the data acquired from the experiment in wide operating ranges than B-K model does. The third model is refined based on GESIM combustion model by including the effect of flame stretch, turbulent length scale band pass filter and a variable that considers flame size and the area of flame contacting the cylinder wall surface. The refined combustion model predicts burning rates closer to experimental results than GESIM combustion model does. Also, the refined combustion model predicts flame radius close to the experimental result measured by using optical fiber technique.

• Journal of Oral Medicine and Pain
• /
• v.26 no.2
• /
• pp.161-171
• /
• 2001

In order to determine how oral mucosal change relates to inducing factors of burning mouth syndrome, the difference in pain perception scale and keratinization rate between burning mouth syndrome patients and normal subjects were investigated. Twenty patients (13 female, 7 male, mean age: 59 years), presenting in the Department of Oral Medicine, Chonnam National University Hospital were participated in this study. All subjects had been complaining of constant oral burning pain for more than a year, none took any strong analgesics, and none had oral mucosal lesions. Twenty volunteers (11 females, 9 males, mean age: 25 years) were also participated in this study as a control group. The control subjects had never had any symptoms of oral burning pain. A thermal stimulation using a Nd-YAG laser and cytological smear were carried out to anterodorsal part of tongue, tip of tongue, the left buccal mucosa, the lower lip mucosa and the chief complaint site. Stimulation of the dorsum of left hand was also carried out to contrast the mucosal area of burning mouth syndrome subjects and the control subjects. The laser output power could be adjusted from 0.75W to 4W. The pain perception scale of the burning mouth syndrome subjects were lower than in control subjects in the chief complaint area, the anterodorsal part of tongue and the buccal mucosa(p<0.01). The keratinization rate of burning mouth syndrome subjects, however, was higher keratinization rate than in normal subjects in the same area and lower lip mucosa(p<0.001). From above results, the anterodorsal part of tongue is the most appropriate site to use diagnostic laser stimulation. The higher level of keratinization and the lower level of thermal pain perception of the burning mouth syndrome subjects are explained as a protective mechanism against xerostomia and burning sensations. The application of Nd-YAG laser stimuli and cytological smear to oral mucosal surface could therefore be usefully employed as appropriate and standardized diagnostic tools for chronic orofacial pain subjects.

• Journal of the Korean Ceramic Society
• /
• v.44 no.9
• /
• pp.517-523
• /
• 2007

For the preparation of tricalciumaluminate $(C_3A)$ clinker, in traditional clinkering method using oxides and carbonates as a raw material, uneconomical repetition of burning have been necessary to avoid the melting of clinker by eutectic reaction in the system $CaO-Al_2O_3$. In this study, special starting raw materials for the clinker burning were prepared from a mixture of oyster shell and aluminium hydroxide by heating to $1100^{\circ}C$ and hydrating at $30^{\circ}C$. The starting raw materials, hardened body with weak hydraulic strength, were mainly composed of $C_3AH_6$ formed by resolution-precipitation mechanism of the system $CaO-Al_2O_3-H_2O$. By heating them, relatively pure $C_3A$ clinker could be obtained by one-time burning at the fairly lower temperature than that of conventional method. The easier formation of $C_3A$ clinker seemed to be caused by higher compositional homogeneity and stoichiometry of the starting materials, high surface area and crystallographic instability of the thermally decomposed products, and the catalytic effect of decomposed moisture on the early-stage crystallization of calciumaluminates. The basic hydration behavior of the clinker was also confirmed.