• Proceedings of the KIEE Conference
• /
• 1998.11b
• /
• pp.689-692
• /
• 1998

In this research a fault-tolerant and bumpless switching control is proposed for boiler systems used in the power plants. Firstly, three operating points are selected to control the nonlinear boiler through the full operational range, and the $H_{\infty}$ loop shaping controller and the model-based predictive controller(MBPC) are designed. To prevent the windup and bump problems which are caused by the actuator saturation and the controller switching, an anti-windup and bump less transfer technique is adopted to the $H_{\infty}$ loop shaping controller. Also the constrained gain-scheduling technique is applied to MBPC to achieve the same objective. Secondly, the fault-tolerant control technique is proposed to continue the control action without stopping the boiler operation even in case of some faults. Through various simulation studies, the performances of the proposed control techniques are demonstrated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.472-475
• /
• 2003

Electric Power Steering (EPS) mechanism has become widely equipped in passenger vehicle due to the environmental consciousness and higher fuel efficiency. This paper describes the development of co-simulation technique and simulation integration technique of EPS control system with dynamic vehicle model. A full vehicle model interacted with EPS control algorithm is concurrently simulated on a single bump road condition. Dynamic responses of vehicle chassis and steering system resulting from road surface impact are evaluated and compared with proving ground experimental data. The comparisons will show reasonable agreement on tie-rod load. rack displacement, handle-wheel torque and tire center acceleration. This developed simulation capability can be used for EPS performance evaluation and calibration as well as for vehicle handling performance integration and synthesis.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.3
• /
• pp.43-48
• /
• 2022

In this study, simulation method was developed to improve the accuracy of the warpage simulation based on the equivalent anisotropic viscoelastic model. First, a package with copper traces and bumps was modeled to implement anisotropic viscoelastic behavior. Then, equivalent anisotropic viscoelastic properties and thermal expansion coefficient for the bump region were derived through the representative volume element model. A thermal cycle of 0 to 125 degrees was applied to the package based on the derived mechanical properties, and the warpage according to the thermal cycle was simulated. To verify the simulation results, the actual package was manufactured, and the warpage with respect to the thermal cycle was measured through shadow moiré interferometer. As a result, by applying the equivalent anisotropic viscoelastic model, it was possible to calculate the warpage of the package within 5 ㎛ error and predict the shape of the warpage.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.6 s.183
• /
• pp.72-80
• /
• 2006

Electric Power Steering (EPS) mechanism has become widely equipped in passenger vehicle due to the increasing environmental concerns and higher fuel efficiency. This paper describes the development of concurrent simulation technique and simulation integration technique of EPS control system with a dynamic vehicle system. A full vehicle model interacting with EPS control algorithm was concurrently simulated on a single bump road condition. The dynamic responses of vehicle chassis and steering system resulting from road surface impact were evaluated and compared with proving ground experimental data. The comparisons show reasonable agreement on tie-rod load, rack displacement, steering wheel torque and tire center acceleration. This concurrent simulation capability was employed fur EPS performance evaluation and calibration as well as for vehicle handling performance integration and synthesis.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.5
• /
• pp.834-840
• /
• 2001

A real time multibody vehicle dynamics model has been developed and implemented using a subsystem synthesis method based on recursive formulation. To verify real time simulation capability the developed model has been applied to HMMWV(High Mobility Multipurpose Wheeled Vehicle) with steering system. For the kinematically driven steering system, the coupled front suspension-steering subsystem can be decoupled into two SLA suspension subsystems, which improves the efficiency of simulation. To investigate theoretical efficiency, operational counting method has been also employed to compare the proposed model with the conventional recursive dynamics model. Various simulations such as unsymmetric bump run, step steering(J-turn) and sine steering input test have been carried out to verify the real time feasibility of the proposed model.

• Journal of Magnetics
• /
• v.16 no.4
• /
• pp.323-327
• /
• 2011

By means of Monte Carlo simulation, we investigate the effects of interface roughness and temperature on the exchange bias and coercivity in ferromagnetic (FM)/antiferromagnetic (AFM) bilayers. Both exchange bias and coercivity are strongly dependent on interface roughness. For a perfect uncompensated interface a domain wall is formed in the AFM system during FM reversal, which results in a very small exchange bias. However, a finite interface roughness leads to a finite value of the exchange bias due to the existence of pinned spins at the AFM surface adjacent to the mixed interface. It is observed that the exchange bias decreases with increasing temperature, consistent with the experimental results. It is also observed that a bump in coercivity occurs around the blocking temperature.

• Advances in materials Research
• /
• v.1 no.1
• /
• pp.83-92
• /
• 2012

The effect of under-bump-metallization (UBM) on electromigration was investigated at temperatures ranging from $135^{\circ}C$ to $165^{\circ}C$. The UBM structures were examined: 5-${\mu}m$-Cu/3-${\mu}m$-Ni and $5{\mu}m$ Cu. Experimental results show that the solder joint with the Cu/Ni UBM has a longer electromigration lifetime than the solder joint with the Cu UBM. Three important parameters were analyzed to explain the difference in failure time, including maximum current density, hot-spot temperature, and electromigration activation energy. The simulation and experimental results illustrate that the addition 3-${\mu}m$-Ni layer is able to reduce the maximum current density and hot-spot temperature in solder, resulting in a longer electromigration lifetime. In addition, the Ni layer changes the electromigration failure mode. With the $5{\mu}m$ Cu UBM, dissolution of Cu layer and formation of $Cu_6Sn_5$ intermetallic compounds are responsible for the electromigration failure in the joint. Yet, the failure mode changes to void formation in the interface of $Ni_3Sn_4$ and the solder for the joint with the Cu/Ni UBM. The measured activation energy is 0.85 eV and 1.06 eV for the joint with the Cu/Ni and the Cu UBM, respectively.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.326-330
• /
• 2007

Bumper back beam is one of the essential structural components of front-end module. It should be designed to withstand a minor bump in low-speed collision, 2.5 mph crash test for example. And weight reduction is always important problem in the design of almost all the parts in car for energy saving. So, the key issues in shape design of a bumper are weight reduction and the performance in 2.5mph crash test. In this study, a light weight and high performance bumper back beam model was developed using analytical approach based on mechanics and FE simulation together.

• Journal of computational fluids engineering
• /
• v.19 no.2
• /
• pp.79-85
• /
• 2014

An air-water free surface flow simulation by using the Lattice Boltzmann Method(LBM) has not been studied a lot compared with the done by the Navier-Stoke equation. This paper shows the LBM is as one of the application tools for the free surface movement over an obstacle. The Mezo scaled application tool has been developed with two dimensional and nine discretized velocity direction using conventional lattice Bhatnagar-Gross-Krook model. Boundary conditions of a halfway-based for solid wall and a kinematic-based for interface are adopted. A validation case with a trapezoidal shape bump to make a comparison between freesurface movements from computational results and experimental ones was described with grid size dependency.

• Journal of Mechanical Science and Technology
• /
• v.19 no.spc1
• /
• pp.312-319
• /
• 2005

For real time dynamic simulation, two different subsystem synthesis methods with independent generalized coordinates have been developed and compared. In each formulation, the subsystem equations of motion are generated in terms of independent generalized coordinates. The first formulation is based on the relative Cartesian coordinates with respect to moving subsystem base body. The second formulation is based on the relative joint coordinates using recursive formulation. Computational efficiency of the formulations has been compared theoretically by the arithmetic operational counts. In order to verify real-time capability of the formulations, bump run simulations of a quarter car model with SLA suspension subsystem have been carried out to measure the actual CPU time.