• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.921-927
• /
• 2001

Steady flow bench test is a practical, powerful and widely used test in most engine manufacturers to give a design concept of a new engine. In order to use steady data as a performance index, it is necessary to build some database, which can correlate the port characteristics with engine data. However, it is very hard to investigate all port and valve shapes with experimental tools. The steady flow scheme is relatively simple and its results are bulk ones such as flow rate and momentum of flow. Therefore a CFD code can be easily applied to the port evaluation. In this study, the steady flow test was simulated through two and three-dimensional analysis on intake port design for comparing with experimental data and confirming the feasibility of applying analytic method. For this purpose, the effect of valve curvature on flow rate was estimated by a CFD code. There results were compared with those of real steady flow tests. As a result, the 2-D analysis described the phenomena qualitatively well, and also the results of 3-D analysis were almost consistent with experimental data.

• Journal of Biosystems Engineering
• /
• 제25권4호
• /
• pp.279-286
• /
• 2000

Most of the domestic cold storage rooms are inefficient for agricultural products because of temperature gradients inside the storage rooms. Temperature gradients are developed mainly by improper airflow pattern inside the storage room, which is a main cause of the spoilage of the agricultural products. There proper airflow pattern is essential to minimize these temperature gradients and the spoilage. The performance and characteristics of a cold storage room were determined as a function of airflow pattern and temperature distribution in forced circulation cold storage room. A commercial CFD(computational fluid dynamics) code was used to simulate 3-D airflow in the cold storage room. Solving the flow equations for the storage room, a standard k-$\varepsilon$ turbulent model was implemented to calculate steady state turbulent velocity distribution. The CFD prediction results were compared with temperature measurements inside the cold storage room. In case of pallet storage, Temperature gradients inside pallet storage was reduced because the contact area of cold air expanded through an alley of airflow in storage. But is case of bulk storage, the last temperature of storage considerably rose more than the initial temperature of storage. The reason was that bulk storage didn't include any alley of airflow in storage.

• 한국가스학회지
• /
• 제17권1호
• /
• pp.26-34
• /
• 2013

상 변화(phase change)를 수반한 다상 유동 연구(multiphase flow analysis)는 증발, 응축과 같은 많은 분야에 적용, 응용될 수 있고 현상의 복잡성 때문에 많은 연구의 관심을 받고 있는 분야이다. 본 연구에서는 극저온 유체인 액화질소가 다양한 밀도의 글라스 울 내부 다공성 매질속으로 스며들면서 나타나는 거동을 살펴보았다. 유동에 영향을 미치는 투과성 계수에 대해서, 외부 압력의 영향성에 대한 실험을 진행하였고 논의하였다. 극저온 유체인 액화질소를 실험유체로 사용하여 사각 기둥 실린더 내부의 유체의 유동에 대한 실험으로 유체의 유동을 살펴보았다. 그 결과 벌크 밀도가 커짐에 따라 투과성 계수가 작아지고, 거리에 따른 압력변화의 비선형성이 커짐을 보였다. 마지막으로 CFD 전산유동 프로그램으로 실험결과와 동일한 상황을 모사하였으며, 이를 실험결과와 비교 분석하였다. 이에 대한 검증결과, 시뮬레이션 결과가 실험결과와 유사한 경향과 결과를 보여주었다.

• 대한화학회지
• /
• 제21권5호
• /
• pp.339-352
• /
• 1977

소성변형에 대한 저자들의 이론(제1보)을 요업재료, 금속, 합금 및 단결정들에 적용하였다. 그 결과 다중 결정에서는 dislocation 운동과 grain boundary 운동이 실험조건에 따라 함께 또는 분리되어 나타나는 반면 단결정에서는 dislocation 운동만 나타났다. 유동식에 나타나는 파라미터$({\alpha}_{d1},\;1/{\beta}_{d1})와\;({\alpha}_{gj}/X_{gj},\;1/{\beta}_{gj})$ (j = 1 or 2) 및 활성화엔탈피 ${\Delta}H_{k1}^{\neq}$ (k = d 혹은 g)를 구하여 예측한 소성변형은 실험과 잘 일치함을 보았다. 여기서 첨자 d1는 첫번째의 dislocation 유동단위, gj는 j번째 grain boundary 유동단위를 나타낸다. 활성화엔탈피에 대하여 ${\Delta}H_{d1}^{\neq}$는 bulk의 자체확산에 대한 활성화엔탈피와 일치하고 ${\Delta}H_{g1}^{\neq}$는 grain boundary 자체확산에 대한 활성화엔탈피와 일치하였다. 이 사실은 저자들의 이론의 정당성을 보이고 있다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.332-337
• /
• 2009

Recently, boss and rib test based on backward extrusion process was proposed to quantitative evaluate the interfacial friction condition in bulk forming process. In this test, the tube-shaped punch with hole pressurizes the workpiece so that the boss and rib are formed along the hole and outer surface of the punch. It was experimentally and numerically revealed that the height of boss is higher than that of the rib under the severe friction condition. This work is focused on the effect of the punch design and friction condition on deformation pattern in boss and rib test. From the boss and rib test simulations, it was found that there is slight variation in both the heights of boss and rib according to the length of punch land, nose radius, and face angle. However the hole diameter of the punch and the clearance between the punch and die have a significant influence on the heights of the boss and rib. In addition, the effect of flow stress was also investigated on the deformation patterns through FE simulations.

• 한국전산유체공학회지
• /
• 제4권1호
• /
• pp.19-26
• /
• 1999

This paper describes a numerical method for predicting the incompressible unsteady laminar three-dimensional flows with free-surface. The Navier-Stokes equations governing the flows have been discretized by means of finite-difference approximations, and the resulting equations have been solved via the SIMPLE-C algorithm. The free-surface is defined by the motion of a set of marker particles and the interface behaviour was investigated by means of a "Lagrangian" technique. Using the GALA concept of Spalding, the conventional mass continuity equation is modified to form a volumetric or bulk-continuity equation. The use of this bulk-continuity relation allows the hydrodynamic variables to be computed over the entire flow domain including both liquid and gas regions. Thus, the free-surface boundary conditions are imposed implicitly and the problem formulation is greatly simplified. The numerical procedure is validated by comparing the predicted results of a periodic standing waves problems with analytic solutions. The results show that this numerical method produces accurate and physically realistic predictions of three-dimensional free-surface flows.

• 대한기계학회논문집B
• /
• 제32권1호
• /
• pp.15-22
• /
• 2008

Recently, ultra-lightweight materials with open, periodic cell structures take much attention owing to its potential for multi-functionality such as load bearing, thermal dissipation, and actuation. This paper presents experimental results on the fluid flow and heat transfer characteristics for the Wire-woven Bulk Kagome (WBK) composed of aluminum 1100 wires. The overall pressure drop and heat transfer of the WBK specimen was experimentally investigated under forced air convection condition. The pressure loss and heat transfer performance of the aluminum WBK were compared with other heat dissipation media. It was shown that heat transfer characteristics depended on relative density and surface area density. Comparison with metal foams and other heat dissipation media such as packed beds, lattice frame materials, louvered fins, and others suggests that the aluminum WBK competes favorably with the best available heat dissipation media in heat transfer performance.

• 펄프종이기술
• /
• 제43권4호
• /
• pp.23-30
• /
• 2011

Fillers have been used for papermaking in order to enhance the optical properties, to improve sheet formation, printability and dimensional stability and to reduce the furnish cost. However, filler particles in paper interfere with fiber-fiber bonding, resulting in decreased paper strength. In order to increase filler content in paper without sacrificing too much paper strength, dual addition technology of fillers was investigated. As a first step, the effects of thick stock addition of fillers on paper properties and papermaking process were elucidated. It was shown that thick stock addition of fillers could increase paper strength at a given filler content. No significant adverse effects on formation, drainage and filler retention were observed. However, bulk of paper was reduced with thick stock addition of fillers, which shall be resolved with regulating other factors such as the mixing ratio of pulps and type of fillers.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.417-420
• /
• 2006

The composition and structure of dendrite phase within $Zr_{76.11}Ti_{4.20}Cu_{4.51}Ni_{3.16}Be_{1.49}Nb_{10.53}$ bulk metallic glass (BMG) were confirmed by using an EPMA, XRD and TEM, respectively. The chief elements of dendrite phase were Zr-Ti-Nb and had a BCC structure. The thermal properties of this BMG have been then subsequently investigated by using a differential scanning calorimeter (DSC). The glass transition and crystallization onset temperatures were determined as $339.7^{\circ}C$ and $375.8^{\circ}C$ for this alloy, respectively. Mechanical properties have also been examined by conducting a series of uniaxial compression tests at various temperatures within supercooled liquid region under the strain rates between $10^{-4}/s$ and $3{\times}10^{-2}/s$. The deformation behavior of BMG composite within supercooled liquid region is similar to one of Vit-1 exhibiting amorphous single phase alloy. The flow stresses of BMG composite, however, are entirely higher than those of Vit-1 because dendrite phases are interfere with moving of atoms.

• International Journal of Fluid Machinery and Systems
• /
• 제10권1호
• /
• pp.76-85
• /
• 2017

Wall pressure measurements and flow visualization were conducted for a 90 degree elbow with an axis curvature radius the same as its inner diameter (125 mm). Reynolds numbers 320,000 and 500,000, based on the inner diameter and bulk velocity, were examined. A deflected inflow, having an almost constant velocity slope and a faster velocity at the inside, was introduced. Ensemble averaged pressure distributions showed that no difference of normalized pressure could be found in both the Reynolds number cases. Power spectral density functions of pressures exhibited that the fluctuation having the Strouhal number (based on the inner diameter and bulk velocity) of 0.6 existed in the downstream region of the elbow, which was 0.1 larger than that of the uniform inflow case [1]. Results of numerical calculations qualitatively coincided with the experimental ones.