• Journal of Dental Rehabilitation and Applied Science
• /
• v.16 no.1
• /
• pp.51-60
• /
• 2000

The purpose of this study was to compare the microleakage at the interface of cast post and tooth according to the type of cement. Forty anterior teeth with single root were used. The teeth were cut 2 mm coronal from the cementoeamel junction and chamfer finish line was made on 1 mm coronal from the cementoeamel junction. After the routine endodontic treatment, post space was prepared using #5.5 Parapost drill to a depth of 7 mm. After the pick up impression, core building was made to 3 mm of clinical crown with burnout wax, then post and core was cast with nonprecious metal. The teeth were divided into four groups of ten each. In Group I, post and core were cemented with Fleck's(Zinc phosphate cement) In Group II, post and core were cemented with Fuji I(Glass ionomer cement) In Group III, post and core were cemented with Superbond C & B(Composite resin cement) In Group IV, post and core were cemented with Panavia 21(Composite resin cement) All cemented teeth were stored in normal saline at $37^{\circ}C$ for 7 days and thermocycled from $5^{\circ}C$ to $55^{\circ}C$ for 500 cycles with a dwell time of 30 seconds. After thermocycling, teeth were immersed in 1% Basic fuchsin dye for 48 hours. All 40 teeth were then embedded in the epoxy resin and cut buccolingually with a cutting instrument. The degree of penetration of dye at interface was graded on a scale of 0 to 4 using a stereomicroscope at 25 to 40 times magnification. Through the findings of this study, the following conclusion were obtained. 1. All the groups showed the microleakage at the interface of cast post core and tooth. 2. Group I showed the highest microleakage score among the groups with a significant difference(p<0.05). 3. Group II showed higher microleakage score than Group III and Group IV with a significant difference(p<0.05). 4. Group IV showed the lowest microleakage score but there were no significant difference with Group III(p>0.05).

• Journal of the Korean Institute of Landscape Architecture
• /
• v.44 no.6
• /
• pp.26-39
• /
• 2016

This research paper explores the process of developing skateboarding spaces in urban parks. Skateboarding is one of the most popular sport activities representative of urban parks. This research paper will analyze the process of introducing skateboarding activities into park spaces and their acceptance by the general public as well as derive meaningful general implications for park space development planning. The research method is a discourse analysis of newspaper articles regarding skateboarding issued between the 1960s and 2010s. These articles are the main resources to show the creation of a skateboarding culture, generation of skate park spaces, and the extinction of these spaces during the research period. The result of this research is as follows. There are reasons that allowed for the creation of skate park spaces in urban parks. First of all, positive associations that people have regarding skateboarding have influenced the park's users and operators' decisions that a park is proper space for skateboarding activities, and the agreement to remodel the park space. Secondly, skate parks became a space for multiple-uses that can be shared with other emerging sports, which resulted in a building boom of skateboarding spaces in urban parks. Thirdly, urban parks and their new culture of active sports became a marketing tool used by local governments to attract new inhabitants to their new towns. On the contrary, there are three main reasons for the deterioration of skate parks. First of all, within parks in which skateboarding activities collided with other park usage, the skate parks disappeared. Secondly, skate parks built specifically for competitive skateboarding events and without consideration of casual skaters disappeared, as these facilities were not sustainable for use in the long term. Thirdly, the golden age of skate park skateboarding did not last long, as skateboarding trends shifted from trick performance to street skating, where skate parks are no longer needed. For this reasons, the exclusive use of park space for skateboarding activities has faded from public interest. The findings of this research suggest how sport activities should be introduced to urban parks. At first, each park's management needs to identify a sport suitable for long-term development, and not only plan for temporal events or follow fleeting trends. Secondly, the park's management systems should reflect a type of sport activity that would not only be popular at the beginning of the spaces development, but also take into consideration how these activities will change over time. Lastly, in cases where there are conflicts between sport activities and other activities in urban parks, attempts should be made to suggest feasible solutions other than the liquidation of sport spaces. This study explains the development process of sport spaces offered in urban parks, by thorough research of the process of acceptance of skateboarding activities in current urban park systems. This conclusion also indicates further areas for research with the purpose of understanding general best practices in urban parks sport space planning.

• Journal of Life Science
• /
• v.25 no.2
• /
• pp.237-242
• /
• 2015

The use of calcite-forming bacteria (CFB) in crack remediation and durability improvements in construction materials creates a permanent and environmentally-friendly material. Therefore, research into this type of application is stimulating interdisciplinary studies between microbiology and architectural engineering. However, the mechanisms giving rise to these materials are dependent on calcite precipitation by the metabolism of the CFB, which raises concerns about possible hazards to cement-based construction due to microbial metabolic acid production. The aim of this study was to determine target microorganisms that possibly can have bio-corrosive effects on cement mortar and to assess multi-functional CFBs for their safe application to cement structures. The chalky test was first used to evaluate the $CaCO_3$ solubilization feature of construction sites by fungi, yeast, bacterial strains. Not all bacterial strains are able to solubilize $CaCO_3$, but C. sphaerospermum KNUC253 or P. prolifica KNUC263 showed $CaCO_3$ solubilization activity. Therefore, these two strains were identified as target microorganisms that require control in cement structures. The registered patented strains Bacillus aryabhatti KNUC205, Arthrobacter nicotianae KNUC2100, B. thuringiensis KNUC2103 and Stenotrophomonas maltophilia KNUC2106, reported as multifunctional CFB (fungal growth inhibition, crack remediation, and water permeability reduction of cement surfaces) and isolated from Dokdo or construction site were unable to solubilize $CaCO_3$. Notably, B. aryabhatti KNUC205 and A. nicotianae KNUC2100 could not hydrolyze cellulose or protein, which can be the major constituent macromolecules of internal materials for buildings. These results show that several reported multi-functional CFB can be applied to cement structures or diverse building environments without corrosive or bio-deteriorative risks.

• Journal of Distribution Science
• /
• v.12 no.6
• /
• pp.15-20
• /
• 2014

Purpose - In general, researchers try to abide by the code of research ethics, but many of them are not fully aware of plagiarism, unintentionally committing the research misconduct when they write a research paper. This research aims to introduce researchers a clear and easy guideline at a conference, which helps researchers avoid accidental plagiarism by addressing the issue. This research is expected to contribute building a climate and encouraging creative research among scholars. Research design, data, methodology & Results - Plagiarism is considered a sort of research misconduct along with fabrication and falsification. It is defined as an improper usage of another author's ideas, language, process, or results without giving appropriate credit. Plagiarism has nothing to do with examining the truth or accessing value of research data, process, or results. Plagiarism is determined based on whether a research corresponds to widely-used research ethics, containing proper citations. Within academia, plagiarism goes beyond the legal boundary, encompassing any kind of intentional wrongful appropriation of a research, which was created by another researchers. In summary, the definition of plagiarism is to steal other people's creative idea, research model, hypotheses, methods, definition, variables, images, tables and graphs, and use them without reasonable attribution to their true sources. There are various types of plagiarism. Some people assort plagiarism into idea plagiarism, text plagiarism, mosaic plagiarism, and idea distortion. Others view that plagiarism includes uncredited usage of another person's work without appropriate citations, self-plagiarism (using a part of a researcher's own previous research without proper citations), duplicate publication (publishing a researcher's own previous work with a different title), unethical citation (using quoted parts of another person's research without proper citations as if the parts are being cited by the current author). When an author wants to cite a part that was previously drawn from another source the author is supposed to reveal that the part is re-cited. If it is hard to state all the sources the author is allowed to mention the original source only. Today, various disciplines are developing their own measures to address these plagiarism issues, especially duplicate publications, by requiring researchers to clearly reveal true sources when they refer to any other research. Conclusions - Research misconducts including plagiarism have broad and unclear boundaries which allow ambiguous definitions and diverse interpretations. It seems difficult for researchers to have clear understandings of ways to avoid plagiarism and how to cite other's works properly. However, if guidelines are developed to detect and avoid plagiarism considering characteristics of each discipline (For example, social science and natural sciences might be able to have different standards on plagiarism.) and shared among researchers they will likely have a consensus and understanding regarding the issue. Particularly, since duplicate publications has frequently appeared more than plagiarism, academic institutions will need to provide pre-warning and screening in evaluation processes in order to reduce mistakes of researchers and to prevent duplicate publications. What is critical for researchers is to clearly reveal the true sources based on the common citation rules and to only borrow necessary amounts of others' research.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.6
• /
• pp.1731-1741
• /
• 2014

Recently, many overpasses, highway, and advanced transit systems have been constructed to distribute the traffic congestion, thus small size of curved bridges with small curvature such as ramp structures have been increasing. Many of early curved bridges had been constructed by using straight beams with curved slabs, but curved steel beams have replaced them due to the cost, aesthetic and the advantage in building the section form and manipulating the curvature of beams, thereby large portion of curved bridges were applied with steel box girders. However, steel box girder bridges needs comparatively high initial costs and continuous maintenance such as repainting, which is the one of the reason for increasing the cost. Moreover, I-type steel plate girder which is being studied by many researchers recently, seem to have problems in stability due to the low torsional stiffness, resulting from the section characteristics with thin plate used for web and open section forms. Therefore, in recent studies, researchers have proposed curved precast PSC girders with low cost and could secured safety which could replace the curved steel girder type bridges. Hence, this study developed a Smart Mold system to manufacture efficient curved precast PSC girders. And by using this mold system a 40 m 2-girder bridge was constructed for a static flexural test, to evaluate the safety and performance under ultimate load. At the manufacturing stage, each single girder showed problems in the stability due to the torsional moment, but after the girders were connected by cross beams and decks, the bridge successfully distributed the stress, thereby the stability was confirmed. The static loading test results show that the initial crack was observed at 1,400 kN when the design load was 450 kN, and the load at the allowable deflection by code was 1,800 kN, which shows that the safety and usability of the curved precast PSC bridge manufactured by Smart Mold system is secured.

• Journal of the Korea Concrete Institute
• /
• v.24 no.3
• /
• pp.275-283
• /
• 2012

Steel Plate for Rebar Connection was recently developed to splice rebars in delayed slab-wall joints in high-rise building, slurry wall-slab joints, temporary openings, etc. It consists of several couplers and a thin steel plate with shear key. Cyclic loading tests on slab-wall joints were conducted to verify structural behavior of the joints having Steel Plate for Rebar Connection. For comparison, joints with Rebend Connection and without splices were also tested. The joints with Steel Plate for Rebar Connection showed typical flexural behavior in the sequence of tension re-bar yielding, sufficient flexural deformation, crushing of compression concrete, and compression rebar buckling. However, the joints with Rebend Connection had more bond cracks in slabs faces and spalling in side cover-concrete, even though elastic behavior of the joints was similar to that of the joints with Steel Plate for Re-bar Connection. Consequently, the joints with Rebend Connection had less strengths and deformation capacities than the joints with Steel Plate for Re-bar Connection. In addition, stiffness of the joints with Rebend Connection degraded more rapidly than the other joints as cyclic loads were applied. This may be caused by low elastic modulus of re-straightened rebars and restraightening of kinked bar. For two types of diameters (13mm and 16mm) and two types of grades (SD300 and SD400) of rebars, the joints with Steel Plate for Rebar Connection had higher strength than nominal strength calculated from actual material properties. On the contrary, strengths of the joints with Rebend Connection decreased as bar diameter increased and as grade becames higher. Therefore, Rebend Connection should be used with caution in design and construction.

• Journal of Radiation Protection and Research
• /
• v.37 no.3
• /
• pp.108-115
• /
• 2012

The Urban Areas Working Group within the EMRAS-2 ($\underline{E}$nvironmental $\underline{M}$odelling for $\underline{RA}$diation $\underline{S}$afety, Phase 2), which has been supported by the IAEA (International Atomic Energy Agency), has designed some types of accidental scenarios to test and improve the capabilities of models used for evaluation of radioactive contamination in urban areas. For the comparison of the results predicted from the different models, the absorbed doses in air were analyzed as a function of time following the accident with consideration of countermeasures to be taken. Two kinds of considerations were performed to find the dependency of the predicted results. One is the 'accidental season', i.e. summer and winter, in which an event of radioactive contamination takes place in a specified urban area. Likewise, the 'rainfall intensity' on the day of an event was also considered with the option of 1) no rain, 2) light rain, and 3) heavy rain. The results predicted using a domestic model of METRO-K have been submitted to the Urban Areas Working Group for the intercomparison with those of other models. In this study, as a part of these results using METRO-K, the countermeasures effectiveness in terms of dose reduction was analyzed and presented for the ground floor of a 24-story business building in a specified urban area. As a result, it was found that the countermeasures effectiveness is distinctly dependent on the rainfall intensity on the day of an event, and season when an event takes place. It is related to the different deposition amount of the radionuclides to the surfaces and different behavior on the surfaces following a deposition, and different effectiveness from countermeasures. In conclusion, a selection of appropriate countermeasures with consideration of various environmental conditions may be important to minimize and optimize the socio-economic costs as well as radiation-induced health detriments.

• Journal of Intelligence and Information Systems
• /
• v.16 no.4
• /
• pp.195-211
• /
• 2010

An exhibition is defined as market events for specific duration to present exhibitors' main product range to either business or private visitors, and it also plays a key role as effective marketing channels. Especially, as the effect of the opinions of the visitors after the exhibition impacts directly on sales or the image of companies, exhibition organizers must consider various needs of visitors. To meet needs of visitors, ubiquitous technologies have been applied in some exhibitions. However, despite of the development of the ubiquitous technologies, their services cannot always reflect visitors' preferences as they only generate information when visitors request. As a result, they have reached their limit to meet needs of visitors, which consequently might lead them to loss of marketing opportunity. Recommendation systems can be the right type to overcome these limitations. They can recommend the booths to coincide with visitors' preferences, so that they help visitors who are in difficulty for choices in exhibition environment. One of the most successful and widely used technologies for building recommender systems is called Collaborative Filtering. Traditional recommender systems, however, only use neighbors' evaluations or behaviors for a personalized prediction. Therefore, they can not reflect visitors' dynamic preference, and also lack of accuracy in exhibition environment. Although there is much useful information to infer visitors' preference in ubiquitous environment (e.g., visitors' current location, booth visit path, and so on), they use only limited information for recommendation. In this study, we propose a booth recommendation methodology using Sequential Association Rule which considers the sequence of visiting. Recent studies of Sequential Association Rule use the constraints to improve the performance. However, since traditional Sequential Association Rule considers the whole rules to recommendation, they have a scalability problem when they are adapted to a large exhibition scale. To solve this problem, our methodology composes the confidence database before recommendation process. To compose the confidence database, we first search preceding rules which have the frequency above threshold. Next, we compute the confidences of each preceding rules to each booth which is not contained in preceding rules. Therefore, the confidence database has two kinds of information which are preceding rules and their confidence to each booth. In recommendation process, we just generate preceding rules of the target visitors based on the records of the visits, and recommend booths according to the confidence database. Throughout these steps, we expect reduction of time spent on recommendation process. To evaluate proposed methodology, we use real booth visit records which are collected by RFID technology in IT exhibition. Booth visit records also contain the visit sequence of each visitor. We compare the performance of proposed methodology with traditional Collaborative Filtering system. As a result, our proposed methodology generally shows higher performance than traditional Collaborative Filtering. We can also see some features of it in experimental results. First, it shows the highest performance at one booth recommendation. It detects preceding rules with some portions of visitors. Therefore, if there is a visitor who moved with very a different pattern compared to the whole visitors, it cannot give a correct recommendation for him/her even though we increase the number of recommendation. Trained by the whole visitors, it cannot correctly give recommendation to visitors who have a unique path. Second, the performance of general recommendation systems increase as time expands. However, our methodology shows higher performance with limited information like one or two time periods. Therefore, not only can it recommend even if there is not much information of the target visitors' booth visit records, but also it uses only small amount of information in recommendation process. We expect that it can give real?time recommendations in exhibition environment. Overall, our methodology shows higher performance ability than traditional Collaborative Filtering systems, we expect it could be applied in booth recommendation system to satisfy visitors in exhibition environment.

• Journal of Intelligence and Information Systems
• /
• v.22 no.4
• /
• pp.69-85
• /
• 2016

Successful relationship with loving partners is one of the most important factors in life. In psychology, there have been some previous researches studying the factors influencing romantic relationships. However, most of these researches were performed based on statistical analysis; thus they have limitations in analyzing complex non-linear relationships or rules based reasoning. This research analyzes commitment and persistence in heterosexual involvement according to styles of loving using a datamining technique as well as statistical methods. In this research, we consider six different styles of loving - 'eros', 'ludus', 'stroge', 'pragma', 'mania' and 'agape' which influence romantic relationships between lovers, besides the factors suggested by the previous researches. These six types of love are defined by Lee (1977) as follows: 'eros' is romantic, passionate love; 'ludus' is a game-playing or uncommitted love; 'storge' is a slow developing, friendship-based love; 'pragma' is a pragmatic, practical, mutually beneficial relationship; 'mania' is an obsessive or possessive love and, lastly, 'agape' is a gentle, caring, giving type of love, brotherly love, not concerned with the self. In order to do this research, data from 105 heterosexual couples were collected. Using the data, a linear regression method was first performed to find out the important factors associated with a commitment to partners. The result shows that 'satisfaction', 'eros' and 'agape' are significant factors associated with the commitment level for both male and female. Interestingly, in male cases, 'agape' has a greater effect on commitment than 'eros'. On the other hand, in female cases, 'eros' is a more significant factor than 'agape' to commitment. In addition to that, 'investment' of the male is also crucial factor for male commitment. Next, decision tree analysis was performed to find out the characteristics of high commitment couples and low commitment couples. In order to build decision tree models in this experiment, 'decision tree' operator in the datamining tool, Rapid Miner was used. The experimental result shows that males having a high satisfaction level in relationship show a high commitment level. However, even though a male may not have a high satisfaction level, if he has made a lot of financial or mental investment in relationship, and his partner shows him a certain amount of 'agape', then he also shows a high commitment level to the female. In the case of female, a women having a high 'eros' and 'satisfaction' level shows a high commitment level. Otherwise, even though a female may not have a high satisfaction level, if her partner shows a certain amount of 'mania' then the female also shows a high commitment level. Finally, this research built a prediction model to establish whether the relationship will persist or break up using a decision tree. The result shows that the most important factor influencing to the break up is a 'narcissistic tendency' of the male. In addition to that, 'satisfaction', 'investment' and 'mania' of both male and female also affect a break up. Interestingly, while the 'mania' level of a male works positively to maintain the relationship, that of a female has a negative influence. The contribution of this research is adopting a new technique of analysis using a datamining method for psychology. In addition, the results of this research can provide useful advice to couples for building a harmonious relationship with each other. This research has several limitations. First, the experimental data was sampled based on oversampling technique to balance the size of each classes. Thus, it has a limitation of evaluating performances of the predictive models objectively. Second, the result data, whether the relationship persists of not, was collected relatively in short periods - 6 months after the initial data collection. Lastly, most of the respondents of the survey is in their 20's. In order to get more general results, we would like to extend this research to general populations.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.38 no.1
• /
• pp.39-48
• /
• 2010

Recreation forests are in the spotlight as the place for personality development, mind and body comfort, companionship, and environment education in forests and valleys. Visitors to recreation forests have been on the increase along with booming in recreation forest building since 1988. Recreation forests are being categorized according to some features such as regional and environmental condition. Recreation forests, however, have not met the expectations of some visitors who want to take a rest with calmness due to the influence of the 5-day-work-week system, increasing interest in rest, leisure, and well-being, and users converge during weekends, summer, and the tourist season. In order to improve visitors' satisfaction efficiently, this study surveyed the level of satisfaction in each cluster based on the precedent study which had classified 85 national or public recreation forests in Korea into clusters. Questionnaires were distributed properly to each cluster and, of the 1,132 questionnaires collected, 1,015 were valid and used for analysis. Reliability of questionnaires and statistical validity of the model were verified. As a result, there are meaningful differences in the ranking of independent variables which affect the level of satisfaction according to clusters. Variables in rest and fatigue recovery have the strongest influence on the level of satisfaction in the clusters of potential factor, internal activation factor, and mixed potential capacity factor. In the use performance and visiting condition factor cluster, appropriateness of visit cost is most influential and, in the education cluster, connectivity with tourist attractions around it is most affective. These results can provide priority in services and maintenance of recreation forests for improving the level of satisfaction and differentiate the distribution of resources according to clusters.