• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.2
• /
• pp.76-84
• /
• 2003

Stereolithography is the technique using a laser beam to cure a liquid resin, a photopolymer, with three dimensional computer-aided design (CAD) data. The build parameters of stereolithography such as beam size, scan velocity. hatch spacing, layer thickness and etc. are determined by the accuracy of prototype, the build time and the cured properties of the resin. In particular, beam size is important processing parameter fur the other parameters. Therefore, this study observed the cured property to beam size. For this purpose, according to hatch spacing and beam size, the cure width and depth were measured on single cured line. Also, the cure width and depth were measured at single cured layer As a result of experiments. cure depth which varied from 0.23mm to 0.34mm was directly proportioned to beam radius. on the other hand, cure width which varied from 0.42mm to 1.07mm was inversely proportioned to beam radius. Surface roughness varied from 1.12 to 2.23 m for the ratio of hatch spacing to beam radius.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.12 s.177
• /
• pp.205-210
• /
• 2005

This paper addresses the correlation between the change of file size and the scanning path build time by the slicing height of STL file. Though the study about STL file has been achieved quite actively scanning path build time using STL file is not investigated so much to be satisfied. The file size depends on the number of polygon created by the slicing height specified. And this number of polygons increases in a regular rate. The correlation between the number of polygons and the scanning path build time is examined and verified.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.50-53
• /
• 2003

Most companies use technologies such as stereolithography, selective laser sintering, and fused deposition modeling to make parts for such small consumer products as telephones, heads, and shoes. The largest part that the existing RP systems can make is only 600 mm in length. Because most RP systems build parts by depositing, solidifying, or sintering material point-by-point, making larger objects takes a long time. and in many cases, large objects won't fit the build size. A new effective thick-layered RP process. Transfer type Variable Lamination Manufacturing using expandable polystyrene foam (VLM-ST) has been developed with thick layers and sloped surfaces. In this paper, a scaledown model of F16 Fighter with the length of 800 mm is rapidly fabricated using the VLM-ST process. In order to build a CAD model of F16 larger than 600 mm in length, the approach in VLM-ST is to build larger parts in multiple sub-parts and then glue them together. The fabricated result shows that the VLM-ST process employing thick layers and sloped surfaces is adequate for creating the real-sized large objects in the diverse fields such as automobiles, electric home appliances, electronics. and etc.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1089-1092
• /
• 2001

In the stereolithography process, build parameters are laser power, scan velocity, scan width, bean diameter, layer thickness and so on. These values are determined according to product accuracy and build time. Build time can be reduced by improving of scan velocity, laser power, layer thickness, hatching space and so on. But variation of these parameters influence part accuracy, surface roughness, strength. This paper observed cure properties in various beam diameter. In order to examine these, relationships of scan velocity and cure depth, scan velocity and cure width according to various beam diameter in one scan line are measured. And cure thickness is measured according to beam diameter and scan velocity in scan surface of one layer. For reduction of build time, beam diameter and scan velocity is proposed in stereolithography process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.397-397
• /
• 2011

In a low aspect ratio (LAR) tokamak reactor with a superconducting toroidal field (TF) coil, the radial build of TF coil and the shield play a key role in determining the size of a reactor. For self-consistent determination of the reactor components and physics parameters, a system analysis code is coupled with one-dimensional radiation transport code. Conceptual design study of a compact superconducting LAR tokamak reactor with aspect ratio less than 2.5 was conducted and the optimum radial build was identified. It is shown that the use of an improved shielding material and high temperature superconducting magnets with high critical current density opens up the possibility of a fusion power plant with compact size and small re-circulating power simultaneously at low aspect ratio, and that by using an inboard neutron reflector instead of breeding blanket, tritium self-sufficiency is possible with outboard blanket only and thus compact sized reactor is viable.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.860-865
• /
• 2000

This Paper Proposes the test pieces of X, Y and Z axes to compensate the shape distortion of Selective Laser Sintering(SLS) parts resulting from the phase change during the sintering process. In no case of the proposed compensation test pieces of X, Y axes the accurate rates of shrinkage can be measured with the reduction of curling which is obtained from adjustment of build orientation and the formula used to get scale factors are proposed with the shrinkage rates of them. The scale factors of X, Y and Z axes are generated by building up proposed compensation test pieces. The generated scale iactors are required to satisfy the dimensional accuracy even if there are changes of the build position and the size of SLS parts in the build chamber. For this reason, it is proposed that the build positions and the size be considered to be noise factors against the compensation test pieces and a method is also proposed that scale factors be selected to robustly maintain the dimensional accuracy of SLS parts under the actual operating conditions with the application of the Taguchi Method.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.05a
• /
• pp.207-209
• /
• 2011

Numerous reports show that alternative project delivery systems (PDSs) such as design-build (DB), construction management at risk (CMR), and design-build-maintain (DBM) are increasingly used in many countries. This study compared characteristics of each PDS (design-bid-build (DBB), DB, CMR, or DBM) by analyzing quantitative data from 9 research articles. In order to compare characteristics between DBB and alternative PDSs, the study is based on principal 3 factors - Time, Cost, and Quality. DB shows the best performance in the time part and also the cost performance depending on facility type and project size. The performance of quality has minor difference among different PDSs. These results support the fact that using an appropriate PDS by the characteristic of a project makes high value of efficiency and productivity.

• Korean Institute of Interior Design Journal
• /
• v.21 no.2
• /
• pp.215-222
• /
• 2012

Design-build is expanding gradually in large construction projects over 10billion won, and continue to work in health care facilities is increasing in this way. This constructional method in health care facilities, despite the many advantages, many problems caused by design changes are being raised. Raises the question of design changes on the side of construction contract, such as approval systems have been studied in the field of construction. The purpose of this study design in aspects of architectural planning on changing the grasp of the issues outlined in the ITB and bid evaluation criteria through consideration of the basic plan for improvement guidelines and evaluation criteria is presented. In conclusion, Design build, according to the presence of existing users are more likely to lead to design changes. Thus, hospital architecture, depending on how it is considered that constructional methods. And evaluation items of ITB(Invitation To Bidder) for a large part of the change in the variables evaluated in the hospital building is not suitable for the design build. Instead, the overall shape of the building and department, unit type and size, vertical and horizontal parts of the circulation system in the shape of the building that does not change in structure and etc should be considered for evaluation.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.38 no.6
• /
• pp.887-895
• /
• 2014

The study provides baseline data on developing ready-to-wear clothes for adult females in their twenties who have finished shaping their bodies and have realized an ideal shape. We analyzed the data from females aged from 20 to 29 in "The $5^{th}$ Size Korea Survey" and "The $6^{th}$ Size Korea Survey", and sorted body shapes into several types according to drop values before analyzing and comparing the characteristics among groups. We also referred to the change by year in the size of upper inner wear. To classify body shapes, three drop values were assigned for bust girth - waist girth, hip girth - waist girth, hip girth - bust girth; through cluster analysis all data were classified into three body types. Type 1 is more like normal body shapes with small drop values at the bust girth - waist girth and well-build lower body. Type 2 is X-shaped body shaped like a fiddle with big drop values at all parts. Type 3 is Y-shaped body with a big drop value at the bust girth - waist girth and well-build upper body. Type 2, X-shaped body, has the majority of distribution in every year, which proved to be the most idealistic body shape. There was a change in the brassiere cup size. Korean ladies in their twenties have larger breasts. The body shapes of Korean females in their twenties are increasingly like those of westerners. Bust girth is a very critical element to set measurements and design patterns for upper wear; consequently, a change in the size of breasts should be considered.

• Proceedings of the IEEK Conference
• /
• 2004.06a
• /
• pp.269-272
• /
• 2004

Printed circuit boards (PCB) replaced conventional wiring in most electronic equipment I, reducing the size and weight of electronic equipment while improving reliability, uniformity, precision and performance. PCB is used in all kinds of electronic products because they can be mass-produced with very high circuit density and also enable easier trouble-shooting. This paper presents the analyses of the patent information of Build-up PCB which is seen as the most promising solution, as its substrate supports multi-level packaging, thinner board profiles and smaller pitches.